Refine Your Search

Search Results

Standard

Carbon Steel Tubing for General Use Understanding Nondestructive Testing for Carbon Steel Tubing

2019-01-04
CURRENT
J2592_201901
This Information Report describes eddy current testing, flux leakage testing, ultrasonic testing, and magnetic particle testing of steel tubing. The purpose of these testing methods is to expose flaws in the tube material or weld zone, such as discontinuities, seams, cracks, holes, voids, and other imperfections characteristic to the specific construction of the tubing. When agreed upon between the producer and purchaser, nondestructive testing is used in lieu of destructive hydrostatic pressure proof testing. Aircraft and Aerospace applications were not considered during the preparation of this document.
Standard

Welded Flash Controlled, High Strength Low Alloy Steel Hydraulic Tubing, Sub-Critically Annealed for Bending, Double Flaring, and Bending

2002-10-25
HISTORICAL
J2613_200210
This SAE Standard covers sub-critically annealed electric resistance welded flash controlled single-wall high strength low alloy steel tubing intended for use in hydraulic pressure lines and in other applications requiring tubing of a quality suitable for bending, double flaring, cold forming, welding and brazing. Material produced to this specification is not intended to be used for single flare applications due to the potential leak path that would be caused by the ID weld bead. The grade of material produced to this specification is of micro-alloy content and is considerably stronger and intended to service higher pressure applications than like sizes of the grades of material specified in SAE J356 and SAE J2435. Due to the alloy content of the material, the forming characteristics of the finished tube are equal to or better, when compared to SAE J356 and SAE J2435. Nominal reference working pressures for this tubing are listed in SAE J1065.
Standard

Welded Flash Controlled, SAE 1021 Carbon Steel Tubing, Normalized for Bending, Double Flaring, and Beading

1999-04-16
HISTORICAL
J2435_199904
The SAE Standard covers normalized electric resistance welded flash controlled single-wall, SAE 1021 carbon steel pressure tubing intended for use as pressure lines and in other applications requiring tubing of a quality suitable for bending, double flaring, beading, and brazing. Material produced to this specification is not intended to be used for single flare applications due to the potential leak path that would be caused by the ID weld bead. The grade of material produced to this specification is higher in carbon content and manganese content than the grade of material specified in SAE J356. The material produced to this specification is intended to service higher pressure applications than like sizes of SAE J356. Due to the higher carbon and manganese content, however, the forming characteristics of the finished tube is diminished somewhat when compared to SAE J356.
Standard

Welded and Cold-Drawn, SAE 1021 Carbon Steel Tubing Normalized for Bending and Flaring

2008-02-08
HISTORICAL
J2467_200802
The SAE Standard covers normalized electric resistance welded, cold-drawn, single-wall, SAE 1021 carbon steel pressure tubing intended for use as pressure lines and in other applications requiring tubing of a quality suitable for bending, flaring, forming, and brazing. The grade of material produced to this specification is higher in carbon content and manganese content than the grade of material specified in SAE J525. The material produced to this specification is intended to service higher pressure applications than like sizes of SAE J525. Due to the higher carbon and manganese content, however, the forming characteristics of the finished tube is diminished somewhat when compared to SAE J525. Special attention to the overall forming requirements of the finished assembly should be taken into consideration when utilizing material produced to this specification.
Standard

Welded Flash Controlled, SAE 1021 Carbon Steel Tubing, Normalized for Bending, Double Flaring, and Beading

2008-02-08
HISTORICAL
J2435_200802
The SAE Standard covers normalized electric resistance welded flash controlled single-wall, SAE 1021 carbon steel pressure tubing intended for use as pressure lines and in other applications requiring tubing of a quality suitable for bending, double flaring, beading, and brazing. Material produced to this specification is not intended to be used for single flare applications due to the potential leak path that would be caused by the ID weld bead. The grade of material produced to this specification is higher in carbon content and manganese content than the grade of material specified in SAE J356. The material produced to this specification is intended to service higher pressure applications than like sizes of SAE J356. Due to the higher carbon and manganese content, however, the forming characteristics of the finished tube is diminished somewhat when compared to SAE J356. Special attention to the overall forming requirements of the finished assembly
Standard

Welded and Cold-Drawn, SAE 1021 Carbon Steel Tubing Normalized for Bending and Flaring

1999-04-16
HISTORICAL
J2467_199904
The SAE Standard covers normalized electric resistance welded, cold-drawn, single-wall, SAE 1021 carbon steel pressure tubing intended for use as pressure lines and in other applications requiring tubing of a quality suitable for bending, flaring, forming, and brazing. The grade of material produced to this specification is higher in carbon content and manganese content than the grade of material specified in SAE J525. The material produced to this specification is intended to service higher pressure applications than like sizes of SAE J525. Due to the higher carbon and manganese content, however, the forming characteristics of the finished tube is diminished somewhat when compared to SAE J525. Special attention to the overall forming requirements of the finished assembly should be taken into consideration when utilizing material produced to this specification.
Standard

Welded and Cold-Drawn, High Strength Low Alloy Steel Hydraulic Tubing, Sub-Critically Annealed for Bending and Flaring

2003-01-30
HISTORICAL
J2614_200301
This specification covers sub-critically annealed electric resistance welded and cold-drawn single-wall high strength low alloy steel tubing intended for use in hydraulic pressure lines and in other applications requiring tubing of a quality suitable for bending, flaring, cold forming, welding and brazing. The grade of material produced to this specification is of micro-alloy content and is considerably stronger and intended to service higher pressure applications than like sizes of the grades of material specified in SAE J525 and SAE J2467. Due to the alloy content of the material, the forming characteristics of the finished tube are equal to or better, when compared to SAE J525 and SAE J2467. Nominal reference working pressures for this tubing are listed in SAE J1065.
Standard

Welded Low-Carbon Steel Tubing

2000-01-01
HISTORICAL
J526_200001
SAE J526 Standard covers welded single-wall low-carbon steel tubing intended for general automotive, refrigeration, hydraulic, and other similar applications requiring tubing of a quality suitable for bending, flaring, beading, forming, and brazing.
Standard

Welded Low-Carbon Steel Tubing

1996-02-01
HISTORICAL
J526_199602
SAE j526 Standard covers welded single-wall low-carbon steel tubing intended for general automotive, refrigeration, hydraulic, and other similar applications requiring tubing of a quality suitable for bending, flaring, bending, forming, and brazing.
Standard

Welded Low-Carbon Steel Tubing Suitable for Bending, Flaring, Beading, Forming and Brazing

2010-11-05
HISTORICAL
J526_201011
The SAE J526 Standard covers electric-resistance welded single-wall low-carbon steel pressure tubing intended for general automotive, refrigeration, hydraulic, and other similar applications requiring tubing of a quality suitable for bending, flaring, beading, forming, and brazing. Material produced to this specification is not intended to be used for single flare applications due to the potential leak path that would be caused by the ID weld bead. The material produced to this specification is intended to service pressure applications where severe forming and bending is not required. As this material may exhibit mechanical properties that reduce some desired forming characteristics versus SAE J356, the severity of the forming requirements of the finished assembly should be considered when utilizing material produced to this specification.
Standard

Welded Flash-Controlled Low-Carbon Steel Tubing Normalized for Bending, Double Flaring, and Beading *HS-150/2000*

1980-01-01
HISTORICAL
J356_198001
The SAE Standard covers normalized electric-resistance welded flash-controlled single-wall, low-carbon steel pressure tubing intended for use as pressure lines and in other applications requiring tubing of a quality suitable for bending, double flaring, beading, forming, and brazing. Material produced to this specification is not intended to be used for single flare applications due to the potential leak path that would be caused by the ID weld bead. This specification also covers SAE J356 Type-A tubing. The mechanical properties and performance requirements of standard SAE J356 and SAE J356 Type-A are the same. Therefore, the designated differences of Type-A tubing are not meant to imply that Type-A tubing is in anyway inferior to standard SAE J356. The Type-A designation is only meant to address the unique manufacturing differences of the small diameter, light wall sizes (typically 15.88 mm OD x 1.24 mm wall and smaller.)
Standard

Welded Flash-Controlled Low-Carbon Steel Tubing Normalized for Bending, Double Flaring, and Beading *HS-150/2000*

1986-05-01
HISTORICAL
J356_198605
The SAE Standard covers normalized electric-resistance welded flash-controlled single-wall, low-carbon steel pressure tubing intended for use as pressure lines and in other applications requiring tubing of a quality suitable for bending, double flaring, beading, forming, and brazing. Material produced to this specification is not intended to be used for single flare applications due to the potential leak path that would be caused by the ID weld bead. This specification also covers SAE J356 Type-A tubing. The mechanical properties and performance requirements of standard SAE J356 and SAE J356 Type-A are the same. Therefore, the designated differences of Type-A tubing are not meant to imply that Type-A tubing is in anyway inferior to standard SAE J356. The Type-A designation is only meant to address the unique manufacturing differences of the small diameter, light wall sizes (typically 15.88 mm OD x 1.24 mm wall and smaller.)
Standard

Welded Flash-Controlled Low-Carbon Steel Tubing Normalized for Bending, Double Flaring, and Beading *HS-150/2000*

1991-06-01
HISTORICAL
J356_199106
The SAE Standard covers normalized electric-resistance welded flash-controlled single-wall, low-carbon steel pressure tubing intended for use as pressure lines and in other applications requiring tubing of a quality suitable for bending, double flaring, beading, forming, and brazing. Material produced to this specification is not intended to be used for single flare applications due to the potential leak path that would be caused by the ID weld bead. This specification also covers SAE J356 Type-A tubing. The mechanical properties and performance requirements of standard SAE J356 and SAE J356 Type-A are the same. Therefore, the designated differences of Type-A tubing are not meant to imply that Type-A tubing is in anyway inferior to standard SAE J356. The Type-A designation is only meant to address the unique manufacturing differences of the small diameter, light wall sizes (typically 15.88 mm OD x 1.24 mm wall and smaller.)
Standard

Welded Flash-Controlled Low-Carbon Steel Tubing Normalized for Bending, Double Flaring, and Beading *HS-150/2000*

2006-07-06
HISTORICAL
J356_200607
The SAE Standard covers normalized electric-resistance welded flash-controlled single-wall, low-carbon steel pressure tubing intended for use as pressure lines and in other applications requiring tubing of a quality suitable for bending, double flaring, beading, forming, and brazing. Material produced to this specification is not intended to be used for single flare applications due to the potential leak path that would be caused by the ID weld bead. This specification also covers SAE J356 Type-A tubing. The mechanical properties and performance requirements of standard SAE J356 and SAE J356 Type-A are the same. Therefore, the designated differences of Type-A tubing are not meant to imply that Type-A tubing is in anyway inferior to standard SAE J356. The Type-A designation is only meant to address the unique manufacturing differences of the small diameter, light wall sizes (typically 15.88 mm OD x 1.24 mm wall and smaller.)
Standard

Welded Flash-Controlled Low-Carbon Steel Tubing Normalized for Bending, Double Flaring, and Beading *HS-150/2000*

1999-05-01
HISTORICAL
J356_199905
The SAE Standard covers normalized electric-resistance welded flash-controlled single-wall, low-carbon steel pressure tubing intended for use as pressure lines and in other applications requiring tubing of a quality suitable for bending, double flaring, beading, forming, and brazing. Material produced to this specification is not intended to be used for single flare applications due to the potential leak path that would be caused by the ID weld bead. This specification also covers SAE J356 Type-A tubing. The mechanical properties and performance requirements of standard SAE J356 and SAE J356 Type-A are the same. Therefore, the designated differences of Type-A tubing are not meant to imply that Type-A tubing is in anyway inferior to standard SAE J356. The Type-A designation is only meant to address the unique manufacturing differences of the small diameter, light wall sizes (typically 15.88 mm OD x 1.24 mm wall and smaller.)
Standard

Welded, Flash-Controlled, Low-Carbon Steel Tubing Normalized for Bending, Double Flaring, Beading, Forming, and Brazing

2019-05-09
CURRENT
J356_201905
This SAE Standard covers normalized electric-resistance welded flash-controlled single-wall, low-carbon steel pressure tubing intended for use as pressure lines and in other applications requiring tubing of a quality suitable for bending, double flaring, beading, forming, and brazing. Material produced to this specification is not intended to be used for single flare applications, due to the potential leak path caused by the Inside Diameter (ID) weld bead or scarfed region. Assumption of risks when using this material for single flare applications shall be defined by agreement between the producer and purchaser. This specification also covers SAE J356 Type-A tubing. The mechanical properties and performance requirements of SAE J356 and SAE J356 Type-A are the same. The SAE J356 or SAE J356 Type-A designation define unique manufacturing differences between coiled and straight material.
X