Search Results

SAE 2011 High Efficiency IC Engines Symposium - Session 3 - Advanced Diesel Engine Technologies Presenter Andrew Brown, Delphi Corp.

The presentation describes the aerodynamic development and optimization process of the three different new models of the Audi A6/A7 family. The body types of these three models represent the three classic aerodynamic body types squareback, notchback and fastback. A short introduction of the flow structures of these different body types is given and their effect on the vehicle aerodynamic is described. In order to achieve good aerodynamic performance, the integration into the development process of the knowledge about these flow phenomena and the breakdown of the aerodynamic resistance into its components friction- and pressure drag as well as the induced drag is very important. The presentation illustrates how this is realized within the aerodynamic development process at Audi. It describes how the results of CFD simulations are combined with wind tunnel measurements and how the information about the different flow phenomena were used to achieve an aerodynamic improvement.

When vehicles share certain information wirelessly via Dedicated Short Range Communications (DSRC), they enable a new layer of electronic vehicle safety that, when needed, can generate warnings to drivers and even initiate automatic preventive actions. Vehicle location and velocity provided by Global Navigation Systems (GNSS), including GPS, are key in allowing vehicle path estimation. GNSS is effective in accurately determining a vehicle's location coordinates in most driving environments, but its performance suffers from obstructions in dense urban environments. To combat this, augmentations to GNSS are being contemplated and tested. This testing has been typically done using a reference GNSS system complimented by expensive military-grade inertial sensors, which can still fail to provide adequate reference performance in certain environments.

Battery Electric Vehicles and Extended Range Electric Vehicles, like the Chevrolet Volt, can use electrical energy from the Grid to meet the majority of a driver�s transportation needs. This has the positive societal effects of displace petroleum consumption and associated pollutants from combustion on a well to wheels basis, as well as reduced energy costs for the driver. CO2 may also be lower, but this depends upon the nature of the grid energy generation. There is a mix of sources � coal-fired, gas -fired, nuclear or renewables, like hydro, solar, wind or biomass for grid electrical energy. This mix changes by region, and also on the weather and time of day. By monitoring the grid mix and communicating it to drivers (or to their vehicles) in real-time, electrically driven vehicles may be recharged to take advantage of the lowest CO2, and potentially lower cost charging opportunities.

In 1991, Hino Motors, Ltd. (Hino) launched the world's first hybrid city buses in the market. Thereafter, Hino has improved its hybrid vehicle technology and applied it to various commercial vehicles including city buses, sightseeing buses, medium-duty trucks and light-duty trucks. Presenter Shigeru Suzuki , Hino Motors, Ltd Shigeru Suzuki , Hino Motors, Ltd

EGR coolers are used in combustion engines to reduce NOx emissions. However, heat transfer in these coolers also results in thermophoresis-temperature-gradient driven motion of suspended particles towards cooler regions-which leads to significant soot deposition. Presenter Meisam Mehravaran

Today CFD is an important tool for engineers in the automotive industry who model and simulate fluid flow. For the complex field of Underhood Thermal Management, CFD has become a very important tool to engineer the cooling airflow process in the engine bay of vehicles. Presenter Peter Gullberg, Chalmers University of Technology

Our trucks today contain anywhere from XX to XX computers on board, some of these computers have the capability to manage algorithms for the correct operation of up to XX systems. Presenter Jesus Gomez, Daimler Trucks North America LLC

Driver assistance systems (e.g. the emergency brake assist Active Brake Assist2, or ABA2 for short, in the Mercedes-Benz Actros) are becoming increasingly common in heavy-duty commercial vehicles. Due to the close interconnection with drivetrain and suspension control systems, the integration and validation of the functions make the most exacting demands on processes and tools involved in mechatronics development. Presenter Thomas Bardelang, Daimler AG

Several technological advancements have enabled hybrid technology to become a viable option in the commercial truck market. Although hybrid trucks are becoming more mainstream, they are not the right alternative fuel solution for every application. When matched with the right duty cycle, hybrid technology can provide a significant cost savings. Due to these advancements and anticipated benefits, hybrid commercial trucks are forecasted to become a significant part of the commercial truck market. Presenter Glenn Ellis, Hino Motors Sales USA Inc.

These advanced checks have resulted in development of many new diagnostic monitors, of varying types, and a whole new internal software infrastructure to handle tracking, reporting, and self-verification of OBD related items. Due to this amplified complexity and the consequences surrounding a shortfall in meeting regulatory requirements, efficient and thorough validation of the OBD system in the powertrain control software is critical. Hardware-in-the-Loop (HIL) simulation provides the environment in which the needed efficiency and thoroughness for validating the OBD system can be achieved. A HIL simulation environment consisting of engine, aftertreatment, and basic vehicle models can be employed, providing the ability for software developers, calibration engineers, OBD experts, and test engineers to examine and validate both facets of OBD software: diagnostic monitors and diagnostic infrastructure (i.e., fault memory management).

Architecting and integrating commercial hybrid electric vehicles (HEV) is a long and labor intensive process which is unique every time. The challenge intensifies when one attempts to create an HEV capable of engine-off operation. Presenter Benjamin Saltsman, Eaton Corp.

We report here results from first year of the BMW MINI E deployment. BMW deployed 450 MINI E?s to North America. Nearly 50% were leased by households in Los Angeles and the New York area. PH&EV Center researchers surveyed MINI E drivers throughout their year with the vehicles, focusing on the experiences of 50 households who volunteered for more detailed interviews. We report here their experiences with driving electric vehicles, adaptions to daily range limitations, and using electricity as a fuel. Presenter Thomas Turrentine, Univ. of California-Davis

ECOtality North America, in partnership with the Idaho National Laboratory (INL), Nissan North America, General Motors, and over 40 government, electric utility, and private organizations, has launched a large-scale demonstration of electric vehicle charging infrastructure. This demonstration, called The EV Project, will deploy more than 15,000 level 2 and DC fast chargers in private residence, commercial, and public locations in seven market areas in Arizona, California, Oregon, Tennessee, Texas, Washington state, and Washington, D.C. The EV Project will also include a total of 5,700 Nissan Leaf battery electric vehicles and 2,600 Chevrolet Volt extended range electric vehicles, operated by consumers and fleets in each of the market areas. This demonstration, which is funded by the U.S. Department of Energy�s (DOE) Vehicle Technologies Program, represents the largest ever deployment of electric vehicles and charging infrastructure.

The presentation provides an overview about the activities of Eurocae Working Group 72 (WG-72) starting with a brief synopsis of the context which suggested why such a committee should be established in 2006. It then goes into further detail about the drivers for the work of the committee, which call for the products to be delivered. It addresses some of the challenges with respect to its users. It points out that one of the lessons the committee learned was importance of the focus on the users, such that the products provide their maximum utility. Hence, the users should better be among the participants to achieve this objective. Other industries have dealt with the subject of Information System (or Cyber-Physical) Security long before this industry was forced to consider it. Consequently there are many industry standards and national or international norms, which may help to develop what is deemed needed for Civil Aviation.

In “Simulation Tools for Engine Design” engineers from Ricardo Software discuss the use of simulation software in new powertrain development. Another engineer, this time from General Motors, talks about how simulation tools helped them solve the challenge of fuel flow reversion while designing the new turbocharged Cadillac V6 engine. This episode highlights: The challenge of simulating complex and combined systems in one vehicle An example of how a library of components in a software package can be chosen to form a specific system and analyzed How computational fluid dynamics simulation tools were used to help redesign a new planum Also Available in DVD Format To subscribe to a full-season of Spotlight on Design, please contact SAE Corporate Sales: CustomerSales@sae.org or 1-888-875-3976.

In “Using Turbocharging in New Engine Design” (9:23), engineers from Schaeffler Group USA and McLaren Performance Tech explain what turbocharging is, and what it can do to improve both the power output of an engine and its fuel efficiency. Another engineer from the General Motors Powertrain group talks about how turbocharging was used in the new engine design for the Cadillac CT6. This episode highlights: The lessons learned from when turbocharging was first used to help heavy-duty trucks go uphill The experience acquired from car racing using turbo-charged engines The advantages of using turbo charging to decrease the size of engines without losing power output Also Available in DVD Format To subscribe to a full-season of Spotlight on Design, please contact SAE Corporate Sales: CustomerSales@sae.org or 1-888-875-3976.

The U.S. Environmental Protection Agency (EPA) contracted with FEV, Inc. to estimate the per-vehicle cost of employing selected advanced efficiency-improving technologies in light-duty motor vehicles. The development of transparent, reliable cost analyses that are accessible to all interested stakeholders has played a crucial role in establishing feasible and cost effective standards to improve fuel economy and reduce greenhouse gas (GHG) emissions. The FEV team, together with engineering staff from EPA's National Vehicle and Fuel Emissions Laboratory, and FEV's subcontractor, Munro & Associates, developed a robust costing methodology based on tearing down, to the piece part level, relevant systems, sub-systems, and assemblies from vehicles ?with and without? the technologies being evaluated.

In Aeronautic industry, when we launch a new industrialization for an aircraft sub assembly we always have the same questions in mind for drilling operations, especially when focusing on lean manufacturing. How can we avoid dismantling and deburring parts after drilling operation? Can a drilling centre perform all the tasks needed to deliver a hole ready to install final fastener? How can we decrease down-time of the drilling centre? Can a drilling centre be integrated in a pulse assembly line? How can we improve environmental efficiency of a drilling centre? It is based on these main drivers that AIRBUS has developed, with SPIE and SOS, a new generation of drilling centre dedicated for hard materials such as titanium, and high thicknesses. The first application was for the assembly of the primary structure of A350 engine pylons. The main solution that was implemented meeting several objectives was the development of orbital drilling technology in hard metal stacks.

ISO 26262 is the actual standard for Functional Safety of automotive E/E (Electric/Electronic) systems. One of the challenges in the application of the standard is the distribution of safety related activities among the participants in the supply chain. In this paper, the concept of a Safety Element out of Context (SEooC) development will be analyzed showing its current problematic aspects and difficulties in implementing such an approach in a concrete typical automotive development flow with different participants (e.g. from OEM, tier 1 to semiconductor supplier) in the supply chain. The discussed aspects focus on the functional safety requirements of generic hardware and software development across the supply chain where the final integration of the developed element is not known at design time and therefore an assumption based mechanism shall be used.