Search Results

Gasoline turbocharged direct injection (GTDI) engines, such as EcoBoost™ from Ford, are becoming established as a high value technology solution to improve passenger car and light truck fuel economy. Due to their high specific performance and excellent low-speed torque, improved fuel economy can be realized due to downsizing and downspeeding without sacrificing performance and driveability while meeting the most stringent future emissions standards with an inexpensive three-way catalyst. A logical and synergistic extension of the EcoBoost™ strategy is the use of E85 (approximately 85% ethanol and 15% gasoline) for knock mitigation. Direct injection of E85 is very effective in suppressing knock due to ethanol's high heat of vaporization - which increases the charge cooling benefit of direct injection - and inherently high octane rating. As a result, higher boost levels can be achieved while maintaining optimal combustion phasing giving high thermal efficiency.

Dimethyl Ether has been proposed as alternative fuel for combustion engines. The paper gives a brief overview of resources, production, distribution and use of different automotive fuels and compares Dimethyl Ether with other oxygenated synthetic fuels recently proposed. For use in combustion engines Dimethyl Ether requires the introduction of new technologies, mainly in the field of fuel injection systems for direct injection. Such a fuel injection system is described in detail and measured characteristics are shown. For assessment of Dimethyl Ether from the environmental point of view, efficiencies and emissions during production and use of different fuels are summarized and discussed. For evaluation of environmental impacts a method is introduced which compares technical processes with natural cycles of substances and thus determines their “sustainability”.

In the past application of alternative fuels was mostly concentrated to special markets - e.g. for ethanol and ethanol blends Brazil or Sweden. Now an increasing sensitivity towards dependency on crude oil significantly enhances the interest in alternative fuels. With spark ignited engines, ethanol and gasoline / ethanol blends are the most promising alternative fuels - besides CNG. The high octane number of ethanol and the resulting excellent knock performance gives significant benefits, especially with highly boosted engines. However, the evaporation characteristics of ethanol result in challenges regarding cold start and oil dilution with GDI application. This paper deals with investigations on a turbocharged DI engine operated on ethanol fuel in order to improve challenges of ethanol fuel, such as oil dilution and cold start. Cold start can be improved by injecting fuel late in the compression stroke (high pressure start) based on a refined engine design and operation strategies.

Worldwide OBD legislation has and will be tightened drastically. In the US, OBD II for PC and the introduction of HD OBD for HD vehicles in 2010 will be the next steps. Further challenges have come up with the introduction of active exhaust gas aftertreatment components to meet the lower future emission standards, especially with the implementation of combined DPF-De-NOx-systems for PC and HD engines. Following such an increase in complexity, more comprehensive algorithms and software have to be developed to cope with the legislative requirements for exhaust gas aftertreatment devices. The calibration has to assure the proper functionality of OBD under all driving situations and ambient conditions. The increased complexity can only be mastered when new and efficient tools and methodologies are applied for both algorithm design and calibration. Consequently, OBD requirements have to be taken into account right from the start of engine development.

The reduction of nitrous oxides in the exhaust gases of internal combustion engines using a urea water solution is gaining more and more importance. While maintaining the future exhaust gas emission regulations, like the Euro 6 for passenger cars and the Euro 5 for commercial vehicles, urea dosing allows the engine management to be modified to improve fuel economy as well. The system manufacturer Robert Bosch has started early to develop the necessary dosing systems for the urea water solution. More than 300.000 Units have been delivered in 2007 for heavy duty applications. Typical dosing quantities for those systems are in the range of 0.01 l/h for passenger car systems and up to 10 l/h for commercial vehicles. During the first years of development and application of urea dosing systems, instantaneous flow measuring devices were used, which were not operating fully satisfactory.

The DEXA Cluster consisted of three closely interlinked projects. In 2003 the DEXA Cluster concluded by demonstrating the successful development of critical technologies for Diesel exhaust particulate after-treatment, without adverse effects on NOx emissions and maintaining the fuel economy advantages of the Diesel engine well beyond the EURO IV (2000) emission standards horizon. In the present paper the most important results of the DEXA Cluster projects in the demonstration of advanced particulate control technologies, the development of a simulation toolkit for the design of diesel exhaust after-treatment systems and the development of novel particulate characterization methodologies, are presented. The motivation for the DEXA Cluster research was to increase the market competitiveness of diesel engine powertrains for passenger cars worldwide, and to accelerate the adoption of particulate control technology.

As emission regulations become tighter and tighter, equipment must evolve to be able to achieve the new standards. Also additional test requirements demand a system that is flexible and can accommodate differences both in the tests and the test facility. By that test cell equipment for chassis dynamometer as well as engine dynamometer applications is getting increasingly complex. That also will require new concepts for the design of such systems. In the past emission system design was more likely a collection and packaging process, which has interfaced various independent components. Now, the development of modern analytical emission systems requires a true holistic design process. This paper will describe the demands and the realization of a modern emission system. It can be shown that an extended effort during the design process will result in a high performance system, which still remains simple and robust.

Emission standards as proposed in Europe and the United States for heavy duty diesel engines will require a NOx and particulate reduction of more than 90%. This cannot be achieved by internal engine measures alone. Aftertreatment systems, for either one or both emission components, plus sophisticated electronic control strategies will be required. Various strategies to comply with EU 4, 5 and US 2007 are discussed, also showing their impact on engine performance. For typical 1 and 2 liter per cylinder engines, emission reduction concepts are assessed to identify the most suitable technology for major worldwide markets. The assessment is based on thermodynamic studies, test-bed results and estimates on cost and infrastructure implications.

DiMethyl Ether (DME) has been shown to be a very attractive fuel for low emission direct injection compression ignition (DICI) engines. It combines the advantages of the high efficiencies of diesel cycle engines with soot free combustion. However, its greatest drawback is the need to develop new fuel injection and handling systems. Previous approaches have been common rail type injection systems which have shown great potential in reducing harmful exhaust emissions and achieving good engine performance and efficiency due to good control of both the fuel injection characteristics and temperature. The concept also has proven benefits with respect to convenient and safe fuel handling. The logical evolution of this concept simplifies the fuel system and avoids special components for DME handling such as high pressure rail pumps while retaining all the benefits of the common rail principle.

Over the last few years there has been much interest in DiMethyl Ether (DME) as an alternative fuel for diesel cycle engines. It combines the advantages of a high cetane number with soot free combustion, which makes it eminently suitable for compression ignition engines. However, due to the fact that it is a gas under ambient conditions, it requires special fuel handling and a specially designed fuel injection system, which until recently, was not available. The use of the digital hydraulic operating system (DHOS), combined with a fuel handling system designed to cope with the properties of DME, enables the fuel to be safely and conveniently handled, In addition, the flexibility of the injection system enables injection pressures to be chosen according to the needs of the combustion.

Exhaust emission legislation world-wide have a common trend towards very low limits, measured for compliance in transient cycles specific for the United States, Japan and Europe. The emission development strategy is focussing on lowest engine-out emissions to require a minimum of exhaust gas aftertreatment. The base engine concept is described and test results, complying with Euro 4, are shown. The emission reduction development for future regulations requires exhaust gas aftertreatment, test results are shown for US 2007, JNLTR and Euro 5. With exhaust gas aftertreatment, discussed in the appendix, the engine development is faced with a big challenge to ensure the minimum exhaust gas temperature required for their proper function.

In recent years several new gasoline engine technologies were introduced in order to reduce fuel consumption. Controlled autoignition seems to be an alternative to stratified part load operation, which is handicapped due to it's lean aftertreatment system for world wide application. The principal advantages of controlled auto ignition combustion under steady state operation - combining fuel economy benefits similar to stratified charge systems with nearly negligible NOx and soot emissions - are already well known. With the newly developed AVL- CSI system (Compression and Spark Ignition), a precise combustion control is achieved even under transient operation. For compensation of production and operation tolerances a cost optimized cylinder individual control was developed. Completely new functionalities of the engine management system are applied. This lean GDI concept complies with future emission standards without DeNOx catalyst and can be applied worldwide.

The combined requirement of achieving CAFE values between 32 to 38 mpg plus LEV/ULEV emission standards to comply with US legal requirements between 1995 and 2000 represents the most demanding challenge for engine engineering. Thus all possible methods of engine improvement towards fuel economy and emissions have to be considered. Besides using new ideas also the methods of engine development have to be modernized to cope with the challenge. The paper presents advanced combustion and exhaust gas aftertreatment systems which combine high power output, favourable torque characteristics and high fuel economy with the potential for obtaining LEV/ULEV emission values, as well as improved development techniques.

With upcoming emission regulations particle emissions for GDI engines are challenging engine and injector developers. Despite the introduction of GPFs, engine-out emission should be optimized to avoid extra cost and exhaust backpressure. Engine tests with a state of the art Miller GDI engine showed up to 200% increased particle emissions over the test duration due to injector deposit related diffusion flames. No spray altering deposits have been found inside the injector nozzle. To optimize this tip sooting behavior a tool chain is presented which involves injector multiphase simulations, a spray simulation coupled with a wallfilm model and testing. First the flow inside the injector is analyzed based on a 3D-XRay model. The next step is a Lagrangian spray simulation coupled with a wallfilm module which is used to simulate the fuel impingement on the injector tip and counter-bores.

The development process of a combustion engine is now a days strongly influenced by future emission regulations which require further reduction in fuel consumption and precise control of combustion process based on Intake air measurement, during engine development. Intake air flow meters clearly differentiate themselves from typical industrial gas flow meters because of their ability to measure extremely dynamic phenomenon of combustion engine. Thus, high internal data acquisition rate, short response time, ability to measure pulsating and reverse flows with lower measurement uncertainty are the factors that ensures the reliability of the results without being affected by ambient influences, sensor contamination or sensor aging. The AVL developed FLOWSONIX™ is based on ultrasonic transit time measuring principle with broad-band Capacitive Ultrasonic Transducer (CUT) characterized by an excellent air impedance matching strongly distinguishes itself by fulfilling all those requirements.

The paper describes a feasibility test program on a 2 liter, 4 cylinder DI/TCI passenger car engine operated on the new alternative fuel Dimethyl Ether (DME, CH3 - O - CH3) with the aim of demonstrating its potential of meeting ULEV emissions (0.2 g/mi NOx in the FTP 75 test cycle) when installed in a full size passenger car. Special attention is drawn to the fuel injection equipment (FIE) as well as combustion system requirements towards the reduction of NOx and combustion noise while keeping energetic fuel consumption at the level of the baseline DI/TCI diesel engine. FIE and combustion system parameters were optimized on the steady state dynamometer by variation of a number of parameters, such as rate of injection, number of nozzle holes, compression ratio, piston bowl shape and exhaust gas recirculation.

The worldwide trend to increasingly stringent exhaust emissions standards, together with consumer requirements, are forcing both vehicle and engine manufacturers, as well as manufacturers of ancilliary equipment, to introduce new and often novel technology in order to produce clean, quiet and socially acceptable transport at affordable prices. The combustion process lies at the heart of the engine and the quality of the combustion determines the acceptability of the product to a very large extent. The fuel injection system plays a large role in the combustion process and in consequence, the fuel system type and capabilities strongly influence the performance of the combustion system. There has never been such a range of fuel injection systems available at one time as there is today. High pressure hydraulically actuated systems /1/ compete with cam driven fuel injection systems /2/ to deliver the injection requirements demanded by the vehicles both of today and in the future.

People have been altering the atmosphere on a small scale ever since they learned to make fire. Today's air pollution can influence ecosystems and transform climate worldwide. Motorized transport has become essential, today about 1000 million vehicles are on the world's roads [1]. Vehicle registrations are still sharply upward, where the future growth is most rapid in Asia and Latin America. Over the past, global pollution concerns have increased and air quality targets have been established. Also the reduction of green house gases like CO2 (Kyoto protocol) is considered. Aligned with such air quality targets automotive emission limits have been implemented. The future emission limits will require advanced engine technologies, but will also require adjustments to the measurement technologies. Furthermore new trends in the emission legislation will increase test requirements to represent the real world conditions in a more realistic way.

The need to improve the engine performance and fuel consumption subject to ever more stringent emission standard spar the interest in the aspects of understanding and quantifying the thermal behavior of engine components and systems. Considering these points during the design of the vehicle thermal management system based on test would consume far too many resources. Fortunately, the simulation tools have become more prominent in the pre-prototype phase of the vehicle development process and they had reached a mature stage; where they can contribute successfully to a significant extend to meet the vehicle development targets. In this work, a methodology to model the Vehicle Thermal Management System (VTMS) in order to understand and quantify its behavior has been developed. The partial systems under consideration are: the gas circuit, the cooling circuit, the lubrication circuit and the thermal capacitance of the engine structure under the vehicle driving conditions.

Increasingly stringent exhaust emission regulations, which are expected to come into force within the next couple of years will require substantial reductions of NOx as well as particulate emissions. To meet these future emission standards, the application of new technologies will be indispensable, especially in view of maintaining or even improving the thermal efficiency of LD, MD and HD diesel engines [1]. Exhaust Gas Recirculation (EGR) is a proven method to reduce NOx emissions. This paper outlines the development and layout of a high load EGR system by means of 3D-CFD and thermodynamic cycle simulation. The analytical approach is presented and simulation results are compared to those achieved on the test bed.