Search Results

Particulate emissions cause adverse health effects and for this reason they are regulated since the 80s. Vehicle regulations cover particulate emission measurements of a model before its sale, known as type approval or homologation. For heavy-duty engines the emissions are measured on an engine dynamometer with steady state points and transient cycles. For light-duty vehicles (i.e. the full power train) the particulate emissions are assessed on a chassis dynamometer. The measurement of particulate emissions is conducted either by diluting the whole exhaust in a dilution tunnel with constant volume sampling or by extracting a small proportional part of the exhaust gas and diluting it. Particulate emissions are measured by passing part of the diluted exhaust aerosol through a filter paper. The increase of the weight of the filter is used to calculate the particulate matter mass (PM) emissions.

To meet LEV and EU Stage III emission requirements, it is necessary for new catalytic converters to be designed which exceed light-off temperature as quickly as possible. The technical solutions are secondary air injection, active heating systems such as the electrically heated catalytic converter, and the close coupled catalytic converter. Engine control functions are extensively used to heat the converter and will to play a significant role in the future. The concept of relocating the converter to a position close to the engine in an existing vehicle involves new conflicts. Examples include the space requirements, the thermal resistance of the catalytic coating and high temperature loads in the engine compartment.

Partial flow sampling methods in emissions testing are interesting and preferred because of their lower cost, smaller size and applicability to engines of all sizes. However the agreement of the results obtained with instruments based on this method to those obtained with the traditional, large tunnel full flow sampling systems needs to be achieved, and the factors of construction that influence this agreement must be understood. These issues have received more attention lately in connection with ISO and WHDC standardization efforts underway to achieve a world-wide harmony in the sampling methods for heavy duty diesel engines, and with the introduction of similar Bag-minidiluter techniques into light duty SULEV gaseous pollutant measurement. This paper presents the theory and practice of a partial flow probe and tunnel design that addresses and minimizes the undesirable effects of the necessary differences between the two sampling methods.

Flame Ionization Detectors (FID) can be used to detect organic hydrocarbons that occur in plastics, lacquers, adhesives, solvents and gasoline. These substances are ionized in the hydrogen flame of the FID. The ionization current that is produced depends on the amount of hydrocarbon in the sample. With the lowering of emissions limits, measuring instruments, including the FID, have to be able to detect very low values. For SULEV (Super-Ultra Low Emissions Vehicle) measurements the accuracy and also the general applicability of the CVS (Constant Volume Sampling) measuring technique are now questioned. Basic understanding is necessary to ask the right questions. One important issue is the science behind the measurement principle of the FID. And in this case especially the influence of contamination of the operating gases, cross sensitivity and data processing on the Limit of Detection (LOD).

The combined requirement of achieving CAFE values between 32 to 38 mpg plus LEV/ULEV emission standards to comply with US legal requirements between 1995 and 2000 represents the most demanding challenge for engine engineering. Thus all possible methods of engine improvement towards fuel economy and emissions have to be considered. Besides using new ideas also the methods of engine development have to be modernized to cope with the challenge. The paper presents advanced combustion and exhaust gas aftertreatment systems which combine high power output, favourable torque characteristics and high fuel economy with the potential for obtaining LEV/ULEV emission values, as well as improved development techniques.

Apart from the reduction of engine-out emissions from the powerplant, the development of an efficient and reliable catalytic converter heating system is an important task of automotive engineering in the future to meet standards that will require reduction of cold start emissions. Carrying out a comprehensive study in this field, BMW has tested and evaluated possible solutions to this challenge. In additon to the electrically heated catalytic converter (E-cat) and the afterburner chamber, an incorporated burner system would meet the requirement for fast catalyst light-off in the future, particularly in the case of larger engines.

In order to achieve the emission levels required for Low Emission Vehicles (LEV) and Ultra Low Emission Vehicles (ULEV) it is necessary to obtain insight into emission reactions to the motor management systems during transient engine performance. The optimisation of transients in typical driving profiles, such as shifting, acceleration load reversal, necessitates suitable gas measurement equipment. A technique capable to resolve one combustion cycle consists in spectroscopic gas analysis by using tunable infrared diode lasers. This paper describes the available equipment and demonstrates that a diode laser system fulfils the specific demands for the analysis of transient operating characteristics of engine management systems.

The paper describes a feasibility test program on a 2 liter, 4 cylinder DI/TCI passenger car engine operated on the new alternative fuel Dimethyl Ether (DME, CH3 - O - CH3) with the aim of demonstrating its potential of meeting ULEV emissions (0.2 g/mi NOx in the FTP 75 test cycle) when installed in a full size passenger car. Special attention is drawn to the fuel injection equipment (FIE) as well as combustion system requirements towards the reduction of NOx and combustion noise while keeping energetic fuel consumption at the level of the baseline DI/TCI diesel engine. FIE and combustion system parameters were optimized on the steady state dynamometer by variation of a number of parameters, such as rate of injection, number of nozzle holes, compression ratio, piston bowl shape and exhaust gas recirculation.

Bag emission measurements on Ultra Low Emission Vehicles require measurement sensitivities in the 1 ppm range for HC and NOx and measurement resolutions well below this to obtain sufficient accuracy and repeatability. Additionally, an analysis of the C2 to C12 components is required. In these emission ranges, adsorption, desorption, diffusion and chemical reaction processes may produce significant effects to the measuring values. Therefore, improvements are necessary to avoid this as far as possible. However, for physical reasons these effects cannot be eliminated completely. For example: Particle filters are not 100% efficient and particles will slowly contaminate the surfaces. Due to physical and chemical processes with some gas components, even stainless steel and Teflon can change their characteristics. Problems resulting from the physical and chemical effects and provisions to minimize the influences to the measuring accuracy and system stability are discussed.

The CBR (Controlled Burn Rate) technology for MPFI engines is known to enable the reduction of throttle losses of gasoline engines by high EGR (Exhaust Gas Recirculation) rates due to the dilution tolerance of the swirl charge motion system using port deactivation. Now a new aspect of CBR is being developed: extremely low emissions during and after cold start. This paper is focused on the combustion stability and low emission aspects of CBR technology. It is shown how engine out emissions and catalyst light off behavior of an engine can be significantly improved using port deactivation. The very stable combustion directly after engine start, extremely retarded ignition timings in combination with lean engine operation and open valve injection with minimized wall wetting lead to very low HC emissions and very high exhaust gas temperatures.

Regarding concepts for naturally aspirated engines, the high potential for fuel economy of Gasoline Direct Injection can only partially be utilized within the constraints of current or future emission legislation like EURO III / IV or LEV/ULEV. Instead of an expected improvement of 20 - 25 % currently only 10 - 15% can be obtained by the engine alone without vehicle optimizations considering all limitations of high volume production. A detailed analysis reveals concrete measures for further improvement. The application of DI gasoline technology clearly favors the combination with other fuel efficient technologies like downsizing by turbocharging and the application of a variable effective compression ratio by intake valve timing variation. Using the flexibility of direct gasoline injection some deficiencies of these technologies can be eliminated.

For the measurement of exhaust emissions, Constant Volume Sampling (CVS) technology is recommended by legislation and has proven its practical capability in the past. However, the introduction of new low emission standards has raised questions regarding the accuracy and variability of the CVS system when measuring very low emission levels. This paper will show that CVS has the potential to achieve sufficient precision for certification of SULEV concepts. Thus, there is no need for the introduction of new test methods involving high cost. An analysis of the CVS basic equations indicates the importance of the Dilution Factor (DF) for calculating true mass emissions. A test series will demonstrate that, by adjusting the dilution and using state of the art analyzers, the consistency of exhaust results is comparable with those of LEV concepts, measured with conventional CVS systems and former standard analyzers.