Search Results

Efforts in aerodynamic optimization of road vehicles have been steadily increasing in recent years, mainly focusing on the reduction of aerodynamic drag. Of a car's total drag, wheels and wheel houses account for approx. 25 percent. Consequently, the flow around automotive wheels has lately been investigated intensively. Previously, the authors studied a treaded, deformable, isolated full-scale tire rotating in contact with the ground in the wind tunnel and using the Lattice-Boltzmann solver Exa PowerFLOW. It was shown that applying a common numerical setup, with velocity boundary condition prescribed on the tread, significant errors were introduced in the simulation. The contact patch separation was exaggerated and the flow field from wind tunnel measurements could not be reproduced. This investigation carries on the work by examining sensitivities and new approaches in the setup.

Knowing the wheel forces on a vehicle under various circumstances and configurations is essential for its aerodynamic development. This becomes crucial when dealing with a racing car. This was the driving force for the initial research conducted in the BMW Aerodynamics Department [1] concerning the aerodynamic forces of an isolated 1:2 racing wheel. The latter were determined for various arrangements with the use of a system equipped with pressure transducers distributed on the wheel surface. While the pressure wheel is adequate for revealing flow structures surrounding it as well as highlighting its physics, it is nevertheless insufficient for the prediction of the wheel forces with high accuracy. As will be shown, this is mainly the consequence of the absent contribution of skin friction, the mathematical method engaged in post–processing and the restricted number of pressure transducers.

Advanced Driver Assistance systems support the driver in his driving tasks. They can be designed to enhance the driver's performance and/or to take over unpleasant tasks from the driver. An important optimization goal is to maintain the driver's activation at a moderate level, avoiding both stress and boredom. Functions requiring a situational interpretation based on the vehicle environment are associated with lower performance reliability than typical stability control systems. Thus, driver assistance systems are designed assuming that drivers will monitor the assistance function while maintaining full control over the vehicle, including the opportunity to override as required. Advanced driver assistance systems have a substantial potential to increase active safety performance of the vehicle, i.e., to mitigate or avoid traffic accidents.

While hybrid-electric powertrain features such as regenerative braking and electric driving can improve the fuel economy of a vehicle significantly, these features may also have a considerable impact on driving dynamics. That is why extra effort is necessary to ensure safety and comfort that customers usually expect from a conventional vehicle. The purpose of this paper is to initiate a discussion regarding different drivetrain concepts, necessary changes in chassis systems, and the impact on vehicle dynamics. To provide input to this essential discussion, braking and steering systems, as well as suspension design, are analyzed regarding their fit with hybrid systems. It is shown how an integration of hybrid technology and chassis systems benefits vehicle dynamics and why “by-wire” technology is a key enabler for safe and comfortable hybrid-electric vehicles.

For the first time, the BMW Active Steering system allows driver-independent steering intervention at the front axle with the mechanical link between the steering wheel and the front axle still in place. The system is primarily comprised of a rack-and-pinion steering system, a double planetary gear and an electric actuator motor. This new level of freedom enables continuous and situation-dependent variation of the steering ratio and therefore adaptation of the transmission behaviour between the steering wheel and the vehicle's reaction to the relevant driving situation. Comfort, steering effort, handling and directional stability have been extensively optimised as a result of this. In addition, driver-independent steering intervention also guarantees vehicle stabilisation in critical driving situations. As a world exclusive, the new Active Steering system will be available for the first time as an option in the new BMW 5 Series.

Highly Automated Driving (HAD) opens up new middle-term perspectives in mobility and is currently one of the main goals in the development of future vehicles. The focus is the implementation of automated driving functions for structured environments, such as on the motorway. To achieve this goal, vehicles are equipped with additional technology. This technology should not only be used for a limited number of use cases. It should also be used to improve Active Safety Systems during normal non-automated driving. In the first approach we investigate the usage of machine learning for an autonomous emergency braking system (AEB) for the active pedestrian protection safety. The idea is to use knowledge of accidents directly for the function design. Future vehicles could be able to record detailed information about an accident. If enough data from critical situations recorded by vehicles is available, it is conceivable to use it to learn the function design.

The NVH-development cycle of vehicle components often requires a source characterization separated from the vehicle itself, which leads to the implementation of test bench setups. In the context of frequency based substructuring and transfer path analysis, a component can be characterized using Blocked Forces. The following paper provides a comparison of methods between an acceleration-based in-situ and a new hybrid in-situ Blocked Force determination, using measurements of an artificially excited electric power steering (EPS). Under real-life conditions on a test rig, the acceleration-based in-situ approach often shows limitations in the lower frequency range, due to relatively bad signal-to-noise ratio at the indicator sensors, while delivering accurate results in the higher spectrum. Due to considerable loads on components in operation, the stiffness of the test-rig cannot be decreased arbitrarily.

Measurements from a Global Navigation System in conjunction with an Inertial Measurement Unit were recently introduced in different aerial and ground vehicles as an input to control vehicle dynamics. In automobiles this approach could help to further improve braking and / or stability control systems as information like velocity over ground and side slip angle becomes available. This paper presents the technical background, validation through test results and the evaluation of potential benefits of such an “INS/GPS” setup. As a result of the extended measuring capabilities a reduction in braking distance and a more effective stability control becomes possible. The results show an excellent performance that should be exploited in future automotive applications.

This paper is supposed to address the BMW approach to the challenge of integrating chassis control systems and it highlights the major issues that have to be addressed. It points out possible solutions for scalable functional and hardware configurations for variable chassis control system combinations. A short outlook is given at possible functional benefits of an integrated structure. Finally, aspects such as components costs (e. g. for sensors and ECUs) as well as reactions on system failures and degradability have to be looked at.

A top-of-the-range car customer not only expects exceptional vehicle design and quality but also a driving experience, which is out of the ordinary. Very harmonious interaction between vehicle dynamics and the steering system is required to offer clients such a consistent driving experience through generations of vehicle models. In this paper the basic properties of a premium driving experience are explored. It is shown that outstanding handling limits are a prerequisite, although most customers never experience such driving situations. In fact, on-center behavior is most crucial in enabling clients to experience part of premium driving performance, and the steering system is the key factor in delivering appropriate feedback to the driver by means of steering torque. Development procedures are presented to achieve the goals described above.

The aim of this report is to present the results obtained from the wind tunnel tests performed in the BMW wind tunnel regarding the pressure distribution on a rotating wheel. The acquired data is used to examine its flow topology for the “open” and “enclosed” cases and determine the wheel drag, lift and side forces by integrating the pressure distribution on its surface. The investigation concerned such measurements on a half scale model wheel. Its pressure distribution was identified with and without the presence of a racecar body. The wheel was also mounted on a half scale passenger car body and pressure measurements were taken with and without a wheel spoiler. After the pressure distributions were known for all configurations, the aerodynamic forces generated were determined. The influence of boundary layer thickness on them was also investigated. A better understanding of the forces the model wheel is subjected to is gained.

The BMW Group is the first car manufacturer introducing FlexRay in series projects. Start of production is September 2006, where a pilot application is implemented in the chassis domain of the new BMW X5. In 2008 FlexRay will form a substantial part of the overall electronics architecture in form of a FlexRay network connecting multiple ECUs implementing chassis, powertrain, and driver assistance applications.

Service-oriented architectures (SOAs) are well-established solutions in the IT industry. Their use in the automotive domain is still on the way. Up to now, the automotive domain has taken advantage of service-oriented architectures only in the area of infotainment and not for systems with hard real-time requirements. However, applying SOA to such systems has just started but is missing suitable design and verification methodologies. In this context, we target to include the notion of model-based design to address fail-operational systems. As a result, a model-based approach for the development of fail-operational systems based on dynamic reconfiguration using a service-oriented architecture is illustrated. For the evaluation, we consider an example function of an automatically controlled braking system and analyze the reconfiguration time when the function fails.