Search Results

The OBD II and EOBD legislation have significantly increased the number of system components that have to be monitored in order to avoid emissions degradation. Consequently, the algorithm design and the related calibration effort is becoming more and more challenging. Because of decreasing OBD thresholds, the monitoring strategy accuracy, which is tightly related with the components tolerances and the calibration quality, has to be improved. A model-based offline simulation of the monitoring strategies allows consideration of component and sensor tolerances as well as a first calibration optimization in the early development phase. AVL applied and improved a methodology that takes into account this information, which would require a big effort using testbed or vehicle measurements. In many cases a component influence analysis is possible before hardware is available for testbed measurements.

Worldwide OBD legislation has and will be tightened drastically. In the US, OBD II for PC and the introduction of HD OBD for HD vehicles in 2010 will be the next steps. Further challenges have come up with the introduction of active exhaust gas aftertreatment components to meet the lower future emission standards, especially with the implementation of combined DPF-De-NOx-systems for PC and HD engines. Following such an increase in complexity, more comprehensive algorithms and software have to be developed to cope with the legislative requirements for exhaust gas aftertreatment devices. The calibration has to assure the proper functionality of OBD under all driving situations and ambient conditions. The increased complexity can only be mastered when new and efficient tools and methodologies are applied for both algorithm design and calibration. Consequently, OBD requirements have to be taken into account right from the start of engine development.

The paper presents the results of the STYFF-DEXA project which has delivered an attractive computational approach based on detailed treatment of the filtration and regeneration processes inside diesel particulate foam filter materials. The new approach can provide accurate macroscopic material parameters by utilizing tomographic data and novel algorithms to reconstruct three-dimensional digital representations of the foam material microstructure. The Lattice-Boltzmann (LB) Method is used as a basis for computing the flow within the foam pores. The latter is coupled to sub-models of particle transport/deposition and size distribution based on the very efficient Method of Moments which employs a probability density function representation of the suspended soot. Additionally, acoustics modelling functionality has been developed which permits the evaluation of the engine noise attenuation capabilities of the foams and similar microstructures.

Wet Clutches are used in automotive powertrains to enable compact designs and efficient gear shifting. During the slip phase of engagement, significant flash temperatures arise at the friction disc to separator interface because of dissipative frictional losses. An important aspect of the design process is to ensure the interface temperature does not exceed the material temperature threshold at which accelerated wear behavior and/or thermal degradation occurs. During the early stages of a design process, it is advantageous to evaluate numerous system and component design iterations exposed to plethora of possible drive cycles. A simulation tool is needed which can determine the critical operational conditions the system must survive for performance and durability to be assured. This paper describes a time-efficient multiphysics model developed to predict clutch disc temperatures with a runtime in the order of minutes.

For the development of complex control algorithms and strategies the engine and powertrain test bed offers a number of advantages over the development in the prototype vehicle. The paper discusses how state-of-the-art simulation techniques can contribute to a continuous development process, which is based upon offline simulation using hardware in the loop, the utilization of modern test bed technology up to vehicle adjustment. The integration of hardware-in-the-loop testing together with vehicle and transmission simulation on the testbed allows to speed up the optimization of fuel consumption, emissions and driveability in an early stage in the development process. The available software tools are presented and application examples are given.

The measurement of vehicle particle number emissions and, therefore, regulation, necessitates a rigorous sampling and conditioning technology able to deliver solid emitted particles with minimum particle losses. European legislation follows a solid particle number measurement method with cutoff size at 23 nm proposed by the Particle Measurement Programme (PMP). Accordingly, the raw exhaust is sampled with constant volume, subsequently passes through a volatile particle remover (VPR), and finally is measured with a particle counter. Lowering the 23 nm cutoff size with current VPR technologies introduces measurement uncertainties mainly due to the high particle losses and possible creation of artefacts. This study describes the development and evaluation of a sampling and conditioning particle system, the SCPS, specially designed for sub-23 nm solid particles measurement.