Search Results

Gearing load spectra data collected under actual working conditions help a designer predict the fatigue life of power train components. Considerable time was required in the past to collect and reduce these data to a form suitable for design use. A vehicle mounted instrumentation system consisting of a strain gaged shaft, a shaft encoder-slip ring assembly, and an amplitude distribution analyzer, was developed which performs load measurements. At the test's conclusion, it provides a spectrum analysis in printed histogram form.

Analytic modeling and analog computer simulation techniques are presented for determining power train transient responses excited by clutch-actuated gear shifts. A method for describing the dynamics of a transmission arrangement having several clutches and interconnected planetary gear sets is considered in detail. Simulation model testing is directed toward optimizing system design parameters and evaluating power train component capability and vehicle shift-feel. Data reduction techniques applied to model responses of torque and speed will yield appropriate spectrums representative of simulated work cycle. The spectrum data are used to predict hours of life for gears, bearings, and driveshafts, according to cumulative fatigue damage theory.

THIS paper presents results which will answer many of the problems facing an engine manufacturer in the selection of the most suitable types and sizes of superchargers to use with a line of engines. Although performance curves of production model diesels are available, decisions are still needed in choosing peak supercharging pressures, drive means, and size and effectiveness of intercoolers, if any. The author describes the use of a typical model to determine response to variation in intake and exhaust conditions, resulting in data which will assist in evaluating engine potentials with any system of supercharging. Thus, supercharger selection for a particular line of engines is aided by knowledge of engine characteristics as a second-stage compressor.

THIS paper points out that the advantages of using light, nonadditive oils are often sacrificed because of lack of fundamental knowledge about gear-scoring problems. Most formulas that have been developed to determine the scoring resistance have been totally empirical and have proved inadequate for stringent design requirements. The author discusses the excellent correlation that exists between scoring test results and a hypothesis on the failure of straight mineral oils. This correlation also encompasses the test results of ball and roller scoring test machines, showing the probable universal application of the hypothesis. The method of approach to the scoring problem of gears as discussed in this paper is a fundamental one, which combines the factors affecting the conversion of frictional energy into surface temperature with gear tooth geometry, stiffness, and surface finish, and points a way to design gears of higher scoring resistance.

This paper first discusses the loads of major significance to various machines and machine parts, and second, considers available methods of measuring, analyzing, and presenting information on loads and stresses. Various engine and machine components are examined from standpoints of loading methods and which loads are likely to be critical on each component. Interrelations between components and machines are also discussed. Tools and methods available to the load and stress analyst are described, with particular emphasis on choices available in methods, instrumentation, and presentation of data. Reasons for preferences in particular situations are given.

SETTING ratings for diesel engines takes laboratory testing and field experience for critical parameters such as smoke, piston temperature, and exhaust temperature. Rating is based upon theoretical considerations, plus the approval of the engine itself. Factors in rating considerations include a knowledge of the application of the engine, and whether its use is to be intermittent or continuous. Ratings by the manufacturer are not always accepted by the engine user, however. The user will run the engine at the load most profitable for him, which may be above or below that recommended by the manufacturer.

A single-shaft, simple-cycle gas turbine engine has been developed to power 200 kw alternators for standby power and for applications where heat is needed. The engine was designed to be sold and serviced by distributors of earthmoving and industrial machinery. Where feasible, design practices of industrial piston engine powered generator sets were incorporated to facilitate installations of combinations of engine types, and to limit novel and unfamiliar features of the basic turbine engine to those that were considered essential. Individual components and complete engines, initially developed by a research group, have been subjected to a wide variety of laboratory tests to measure performance and develop reliability.

This paper demonstrates a way of applying an iterative computing technique to a typical engineering design problem, in such a way as to maximize a mathematical expression of the design criteria. Ways of writing this mathematical expression to express design criteria are explained through several illustrative examples. This technique of computer-aided design should allow the engineer to arrive at more than satisfactory designs in a minimum of engineering time.

A new 2-ring piston package has been developed which has proven successful in internal combustion engines. The need for a compact piston arrangement is discussed along with the steps followed to arrive at excellent oil economy. The paper presents other advantages related to cost savings, lower wear, and reduced engine friction. The paper discusses applications of the compact piston package along with its advantages in designing compact engines.

This Paper: 1. Shows that the present spherical rod end manufacturer's rotational tests, which are intended to select the best bearing material, do not necessarily select the best materials for the push/pull linkage requirements of earthmoving machinery. 2. Emphasizes the need to perform push/pull comparative testing as defined in SAE J1367 on spherical rod ends to determine acceptable materials for earthmoving equipment application. This test is in contrast to rotational testing presently being performed by spherical rod end manufacturers.

The small wheel type loader has seen its application range extended such that it is now one of the most versatile machines in our industry. However, its effectiveness in tasks other than bucket loading is limited. In order to provide improved tool control characteristics that contribute to efficient multi-task capability, it is necessary to design these characteristics into the base vehicle. The Integrated Toolcarriers recently introduced by Caterpillar fulfill this requirement. This paper discusses the design objectives and summarizes the development program which preceded their introduction.

Fatigue failure of machine components subjected to high contact pressures is rapidly becoming recognized as a serious design limitation. Confusion has resulted from grouping three distinct types of contact fatigue failure under the term “pitting” A Geared Roller Test Machine is described that reproduced each of the three modes of failure. The stress-life relationships obtained for rollers tested under conditions of rolling plus sliding correlated well with actual gear performance. The sensitivity of the test to changes in material, micorstructure, and processing variables is demonstrated.

TVA is an interactive computer program which performs a Torsional Vibration Analysis on lumped mass systems which contain torsional degrees of freedom. This program has two fundamental analyses. The first is Normal Modes which analyzes the natural unforced undamped behavior of the system to give natural frequencies and mode shapes. The second analysis is Frequency Response which analyzes the forced response of a damped system to give response results. TVA is used to analyze engine-auxilary equipment systems as well as vehicle drivetrain systems.

THE CATERPILLAR FOLDED CORE RADIATOR IS A NEW RADIATOR FOR VEHICLES AND STATIONARY ENGINE APPLICATIONS. THE MAJOR OBJECTIVES OF THIS DESIGN ARE TO GIVE THE USER AN INCREASED VALUE COOLING SYSTEM BY REDUCING RADIATOR REPAIR COSTS AND IMPROVING AIR-SIDE PLUGGING RESISTANCE. AS WELL AS PROVIDE THE VEHICLE DESIGNER WITH INCREASED APPLICATION DESIGN FLEXIBILITY. THIS IS TO BE ACCOMPLISHED WHILE MAINTAINING PERFORMANCE AND LIFE GOALS ASSOCIATED WITH THE CONVENTIONAL RADIATOR. THE FOLDED CORE IS A MODULAR DESIGN HAVING THE MODULES INSTALLED AT AN ANGLE TO THE FAN AIR STREAM RESULTING IN THE FOLDED APPEARANCE. COMMON MODULE SIZES ARE USED ACROSS THE MANY RADIATOR APPLICATIONS REDUCING INVENTORY REQUIREMENTS AT THE ASSEMBLY PLANT AND PARTS DEPOTS AND INCREASING INDIVIDUAL MODULE PRODUCTION VOLUME. THIS RADIATOR DESIGN IS REVIEWED FROM CONCEPT TO PRODUCTION.