Search Results

Gearing load spectra data collected under actual working conditions help a designer predict the fatigue life of power train components. Considerable time was required in the past to collect and reduce these data to a form suitable for design use. A vehicle mounted instrumentation system consisting of a strain gaged shaft, a shaft encoder-slip ring assembly, and an amplitude distribution analyzer, was developed which performs load measurements. At the test's conclusion, it provides a spectrum analysis in printed histogram form.

THIS paper presents results which will answer many of the problems facing an engine manufacturer in the selection of the most suitable types and sizes of superchargers to use with a line of engines. Although performance curves of production model diesels are available, decisions are still needed in choosing peak supercharging pressures, drive means, and size and effectiveness of intercoolers, if any. The author describes the use of a typical model to determine response to variation in intake and exhaust conditions, resulting in data which will assist in evaluating engine potentials with any system of supercharging. Thus, supercharger selection for a particular line of engines is aided by knowledge of engine characteristics as a second-stage compressor.

The heavy-duty truck industry has seen the need for a change in the concept of transmission design for many years. Several improvements have been made and others attempted, but greater improvement is needed to match the engine's delivery to the vehicle's demand. Driver performance can be improved and fatigue reduced by lowering the effort and skill required to make smooth, consistent starts and ratio changes. This paper discusses a solution to this need in the design and development of a semi-automatic, pneumatically controlled, constant mesh transmission.

HIGH load-carrying ability and fatigue strength, good embeddabiltty and conformability, and resistance to wear, seizure, and corrosion are factors that sold them on aluminum for bearings, the authors report. Bonded steel backing, they say, makes aluminum bearings even better. Retaining aluminum's good properties, it improves some of its bad points and gives such advantages as: Reduced bearing clearances, compared with those used with solid-aluminum bearings. No life limit in operation below 5000 psi fatigue stress value. Less sensitivity to high oil temperatures. Negligible wear (after 29,000 hr in one test). Simpler and less expensive bearing-locating designs. Special excellence for high-load, high-speed applications.

SETTING ratings for diesel engines takes laboratory testing and field experience for critical parameters such as smoke, piston temperature, and exhaust temperature. Rating is based upon theoretical considerations, plus the approval of the engine itself. Factors in rating considerations include a knowledge of the application of the engine, and whether its use is to be intermittent or continuous. Ratings by the manufacturer are not always accepted by the engine user, however. The user will run the engine at the load most profitable for him, which may be above or below that recommended by the manufacturer.

Recent developments in engine designs have produced engines that have shorter response time, thus making it increasingly difficult to control speed. Dynamic response of the engine and governor system is usually neglected when designing a governor. The recommended procedure for designing an engine governor is to develop a preliminary static design of the governor, analyze the engine using frequency response, mathematically analyze the static design of the governor, similate the two analyses on an electrical analog computer, and then determine from the computer results the changes that are necessary to get a satisfactory governor design.

A new friction welding process, Caterpillar Inertia Welding, is described in this paper. The two distinguishing characteristics of this form of welding are a continuously decreasing rotational velocity and a continuously changing torque at the weld interface. This enables the forging of many previously “difficult-to-weld” materials, such as superalloys. Such welds also exhibit excellent fatigue properties. Because this process produces high strength bonds in dissimilar materials, the designer is able to create composite parts using the special properties of each material in response to the needs of the design.

A single-shaft, simple-cycle gas turbine engine has been developed to power 200 kw alternators for standby power and for applications where heat is needed. The engine was designed to be sold and serviced by distributors of earthmoving and industrial machinery. Where feasible, design practices of industrial piston engine powered generator sets were incorporated to facilitate installations of combinations of engine types, and to limit novel and unfamiliar features of the basic turbine engine to those that were considered essential. Individual components and complete engines, initially developed by a research group, have been subjected to a wide variety of laboratory tests to measure performance and develop reliability.

The Cushion Hitch is a unique application of vibration absorber theory to a self-propelled tractor-scraper. The scraper mass is utilized as a damper for suppressing predominate bouncing motions of the tractor unit. A more comfortable and safer operator ride, with increased productivity, results from the Cushion Hitch application. This paper describes development of the early prototype design as well as the final production version. Particular emphasis is given to both the hydraulic and the structural characteristics of the system.

A new 2-ring piston package has been developed which has proven successful in internal combustion engines. The need for a compact piston arrangement is discussed along with the steps followed to arrive at excellent oil economy. The paper presents other advantages related to cost savings, lower wear, and reduced engine friction. The paper discusses applications of the compact piston package along with its advantages in designing compact engines.

This Paper: 1. Shows that the present spherical rod end manufacturer's rotational tests, which are intended to select the best bearing material, do not necessarily select the best materials for the push/pull linkage requirements of earthmoving machinery. 2. Emphasizes the need to perform push/pull comparative testing as defined in SAE J1367 on spherical rod ends to determine acceptable materials for earthmoving equipment application. This test is in contrast to rotational testing presently being performed by spherical rod end manufacturers.

Fatigue failure of machine components subjected to high contact pressures is rapidly becoming recognized as a serious design limitation. Confusion has resulted from grouping three distinct types of contact fatigue failure under the term “pitting” A Geared Roller Test Machine is described that reproduced each of the three modes of failure. The stress-life relationships obtained for rollers tested under conditions of rolling plus sliding correlated well with actual gear performance. The sensitivity of the test to changes in material, micorstructure, and processing variables is demonstrated.

THE CATERPILLAR FOLDED CORE RADIATOR IS A NEW RADIATOR FOR VEHICLES AND STATIONARY ENGINE APPLICATIONS. THE MAJOR OBJECTIVES OF THIS DESIGN ARE TO GIVE THE USER AN INCREASED VALUE COOLING SYSTEM BY REDUCING RADIATOR REPAIR COSTS AND IMPROVING AIR-SIDE PLUGGING RESISTANCE. AS WELL AS PROVIDE THE VEHICLE DESIGNER WITH INCREASED APPLICATION DESIGN FLEXIBILITY. THIS IS TO BE ACCOMPLISHED WHILE MAINTAINING PERFORMANCE AND LIFE GOALS ASSOCIATED WITH THE CONVENTIONAL RADIATOR. THE FOLDED CORE IS A MODULAR DESIGN HAVING THE MODULES INSTALLED AT AN ANGLE TO THE FAN AIR STREAM RESULTING IN THE FOLDED APPEARANCE. COMMON MODULE SIZES ARE USED ACROSS THE MANY RADIATOR APPLICATIONS REDUCING INVENTORY REQUIREMENTS AT THE ASSEMBLY PLANT AND PARTS DEPOTS AND INCREASING INDIVIDUAL MODULE PRODUCTION VOLUME. THIS RADIATOR DESIGN IS REVIEWED FROM CONCEPT TO PRODUCTION.