Search Results

In order to understand the spray impinging the lubricant oil on the piston or cylinder wall in GDI engine, the Laser Induced Fluorescence (LIF) method was used to observe the phenomenon of the fuel droplets impact oil film and distinguish the fuel and oil during the impingement. The experimental results show that the hydrodynamic characteristics of impingement affected by the oil viscosity, droplets’ Weber number, oil film thickness. Crown formed after impingement. The morphology after impingement was categorized into: rings, stable crown, splash and prompt splash. Low oil film dynamic viscosity, high Weber number or thin oil film can facilitate splash. Splash droplets consist of fuel and oil, and the oil is the main component of splash droplets and crown. The empirical formula of critical We number (We) is fitted. High dimensionless oil film thickness or low oil film dynamic viscosity can increase the proportion of fuel in the crown.

In this paper, the influences of metallic content of lubricating oils on diesel particles were investigated. Three lubricating oils with different levels of metallic content were used in a 2.22 Liter, two cylinders, four stroke, and direct injection diesel engine. 4.0 wt. % and 8 wt. % antioxidant and corrosion inhibitor (T202) were added into baseline lubricating oil to improve the performance respectively. Primary particle diameter distributions and particle nanostructure were compared and analyzed by Transmission Electron Microscope. The graphitization degrees of diesel particles from different lubricating oils were analyzed by Raman spectroscopy. Conclusions drawn from the experiments indicate that the metallic content increases the primary particles diameter at 1600 rpm and 2200 rpm. The primary particles diameter ranges from 5 nm to 65 nm and the distribution conformed to Gaussian distribution.

The combustion of cylinder lubricating oil (called as cylinder oil for short) is one of the major sources of PM emissions of low-speed 2-stroke marine diesel engines. For pre-mixed combustion low-speed 2-stroke marine gas engines, the auto-ignition of cylinder oil might result in knock or more hazard abnormal combustion - pre-ignition. Evaporation is a key sub-process of the auto-ignition process of cylinder oil droplets. The evaporation behavior has a profound impact on the auto-ignition and combustion processes of cylinder oil droplets, and a great influence on engine combustion performance and emission characteristics. This paper applied an oil suspending apparatus to investigate the evaporation behavior of cylinder oil droplets and base oil droplets. The effects of ambient temperatures on the evaporation process were measured and analyzed. The results indicate that the evaporation of cylinder oil includes heating, evaporating, pyrolysis, and polymerization.

The aim of this research is to investigate the effects of ashless dispersant of lube oils on diesel exhaust particles. Emphasis is placed on particle size, morphology, nanostructure and graphitization degree. Three kinds of lube oils with different percentages of ashless dispersant were used in a two-cylinder diesel engine. Ashless dispersant (T154), which is widely used in petrochemical industry, were added into baseline oil at different blend percentages (4.0% and 8.0% by weight) to improve lubrication and cleaning performance. A high resolution Transmission Electron Microscope (HRTEM) and a Raman spectroscopy were employed to analyze and compare particle characteristics. According to the experiment results, primary particles diameter ranges from 3 nm to 65 nm, and the diameter distribution conformed to Gaussian distribution. When the ashless dispersant was used, the primary particles diameter decrease obviously at both 1600 rpm and 2200 rpm.

The abnormal combustion resulted by the auto-ignition of lubricating oil is a great challenge to the development of Otto-cycle gas engines. In order to investigate the mechanism of lubricating oil droplet vaporization process, a crucial sub-process of auto-ignition process, a new multi-component vaporization model was constructed for high temperature and pressure, and forced gas flow conditions as encountered in practical gas engines. The vaporization model has been conducted with a multi-diffusion sub-model considering the multi-component diffusivity coefficients in the gas phase. The radiation heat flux caused by ambient gas was taken into account in high temperature conditions, and a real gas equation of state was used for high pressure conditions. A correction for mass vaporization rate was used for forced gas flow conditions. Extensive verifications have been realized, and considerable results have been achieved.