Search Results

Owing to the small size of engines and high injection pressures, it is difficult to avoid the fuel spray impingement on the combustion cylinder wall and piston head in Direct Injection Spark Ignition (DISI) engine, which is a possible source of hydrocarbons and soot emission. As a result, the droplets size and distribution are significantly important to evaluate the atomization and predict the impingement behaviors, such as stick, spread or splash. However, the microscopic behaviors of droplets are seldom reported due to the high density of small droplets, especially under high pressure conditions. In order to solve this problem, a “spray slicer” was designed to cut the spray before impingement as a sheet one to observe the droplets clearly. The experiment was performed in a constant volume chamber under non-evaporation condition, and a mini-sac injector with single hole was used.

Lean-burn combustion is an effective method for increasing the thermal efficiency of gasoline engines fueled with stoichiometric fuel-air mixture, but leads to an unacceptable level of high cyclic variability before reaching ultra-low nitrogen oxide (NOx) emissions emitted from conventional gasoline engines. Multi-point micro-flame ignited (MFI) hybrid combustion was proposed to overcome this problem, and can be can be grouped into double-peak type, ramp type and trapezoid type with very low frequency of appearance. This research investigates the micro-flame ignition stages of double-peak type and ramp type MFI combustion captured by high speed photography. The results show that large flame is formed by the fast propagation of multi-point flame occurring in the central zone of the cylinder in the double-peak type. However, the multiple flame sites occur around the cylinder, and then gradually propagate and form a large flame accelerated by the independent small flame in the ramp type.

The combustion and emission characteristics of a diesel engine running on butanol-diesel blends were investigated in this study. The blending ratio of n-butanol to diesel was varied from 0 to 40 vol% using an increment of 10 vol%, and each blend was tested on a 2.7 L V6 common rail direction injection diesel engine equipped with an EGR system. The test was carried out under two engine loads at a constant engine speed, using various combinations of EGR ratios and injection timings. Test results indicate that n-butanol addition to engine fuel is able to substantially decrease soot emission from raw exhaust gas, while the change in NOx emissions varies depending on the n-butanol content and engine operating conditions. Increasing EGR ratio and retarding injection timing are effective approaches to reduce NOx emissions from combustion of n-butanol-diesel blends.

Working process of diesel engine refers to airflow, turbocharger, fuel injection, combustion, heat transfer and chemical reaction powers etc. Hence, it influences power output, fuel consumption, combustion noise and emissions, moreover directly influences reliability and durability of diesel engine. The working process of 6106 diesel engine is simulated by large universal internal combustion engine working process numerical simulation software GT-Power in this paper, and the effects of compression ratio, fuel supply advance angle and valve timing system on performance of diesel engine are analyzed. When valve-timing system is studied, the influence of intake valve close timing, exhaust valve open timing and valve overlap angle on performance are analyzed. On different operating conditions, the different timing of intake close and exhaust open, valve overlap were computed and analyzed. Finally, at different engine conditions, various optimum results were obtained.

Porous medium (PM) engine was a new type engine based on the technique of combustion in porous medium, which can realize homogeneous and stable combustion. In this paper, the combustion and working processes of a specific PM engine was simulated by a two-zone model considering the influences of the mass distribution, heat transfer from the cylinder wall, mass exchange between zones and the heat transfer in porous medium. Influences of operating parameters, e.g. intake temperature and pressure, compression ratio, the excess air ratio on the performance of the PM engine were discussed. It is found out that the porous medium, acting as a heat recuperator, can significantly enhance the evaporation of liquid fuel and preheat the mixture, which promotes the ignition and combustion in the cylinder; and that the initial PM temperature and the compression ratio are critical factors controlling the compression ignition of the mixture.

To understand the working mechanism of the porous medium (PM) internal combustion engine, effects of a porous medium heat regenerator inserted into a combustion chamber on the turbulent flow field and fuel-air mixture formation are studied by numerical simulation. The cylindrical chamber has a constant volume, in which a disk-shaped PM insert is fixed. A simplified model for the random structure of the PM is presented, in which the PM is represented by an assembly of a great number of randomly distributed solid units. To simulate flows in the PM a Brinkman-Forchheimer-extended Darcy's equation is introduced into the numerical solver. A version of two-equation k - ε turbulence model suggested by Antohe and Lage is employed for the turbulence prediction in the PM. A spray model, in which the effects of drop breakup, collision and coalescence are taken into account, is introduced to describe spray/wall interactions.

A zero-dimension combustion model suitable to multi-fuel combustion process has been developed and successfully used in the analysis of methanol combustion process The V2b function is calculated with the Powell Optimized Algorithm. The concerned characteristics include in the variables of zero-dimension model, mean indication pressure, maximum combustion pressure, ignition delay and the correlation coefficient between heat release rate and ignition delay. The heat release rate curves on different conditions are fitted and the statistic analyses of the cyclic variations are conducted.

This paper presents two factors for improving the performance and emissions characteristics in HCCI diesel combustion, one is reducing compression ratio and another is changing the injector position. In a previous study, it was shown that HCCI diesel combustion could be realized by utilizing a hollow-cone spray with normal injection pressure. However there remained two major problems of engine instability and increase in BSFC (decrease in brake thermal efficiency). By reducing the compression ratio from 18.8 to 16.8, the engine stability was much improved to the level of conventional diesel combustion and the increase in BSFC became almost half, which was mainly due to the change of combustion phasing. In addition to this, application of 5 mm inside position of the injector realized almost no penalty of BSFC at higher load condition.

This paper investigates the difference between the traditional diffusion combustion and hot premix film type combustion on improvement of compression ignition engine performance in all respects. The first part of this paper mainly describes the heat release, air fuel mixing, swirl flow and squish flow and also film formation on diffusion combustion. The second part of this paper describes the development of hot premix combustion, its feasibility and guiding principles. The main purpose of this part is to demonstrate three main measures which should be taken in carrying out premix film formation combustion. The first means is air flow guide ring. The second is film formation process and the third is fine particles fuel injectors: one is supermultiple holes injector and the second is conical spray fuel injector.

In this paper, a control-oriented soot model was developed for real-time soot prediction and combustion condition optimization in a gasoline Partially Premixed Combustion (PPC) Engine. PPC is a promising combustion concept that achieves high efficiency, low soot and NOx emissions simultaneously. However, soot emissions were found to be significantly increased with high EGR and pilot injection, therefore a predictive soot model is needed for PPC engine control. The sensitivity of soot emissions to injection events and late-cycle heat release was investigated on a multi-cylinder heavy duty gasoline PPC engine, which indicated main impact factors during soot formation and oxidation processes. The Hiroyasu empirical model was modified according to the sensitivity results, which indicated main influences during soot formation and oxidation processes. By introducing additional compensation factors, this model can be used to predict soot emissions under pilot injection.

Acetone-Butanol-Ethanol (ABE) is an intermediate product in the ABE fermentation process for producing bio-butanol. As an additive for diesel, it has been shown to improve spray evaporation, improve fuel atomization, enhance air-fuel mixing, and enhance combustion as a whole. The typical compositions of ABE are in a volumetric ratio of 3:6:1 or 6:3:1. From previous studies done in a constant volume chamber, it was observed that the presence of additional acetone in the blend caused advancement in the combustion phasing, but too much acetone content led to an increase in soot emission during combustion. The objective of this research was to investigate the combustion of these mixtures in a diesel engine. The experiments were conducted in an AVL 5402 single-cylinder diesel engine at different speeds and different loads to study component effects on the various engine conditions. The fuels tested in these experiments were D100, ABE(3:6:1)10, ABE(3:6:1)20, ABE(6:3:1)10, and ABE(6:3:1)20.

Dimethyl ether (DME) attracts increasing attentions in recent years, because it can reduce the carbon monoxide (CO), unburned hydrocarbon (HC), and soot emissions for engines as the transportation fuel or the fuel additive. In this paper, a reduced DME oxidation mechanism is developed using the decoupling methodology. The rate constants of the fuel-related reactions are optimized using the non-dominated sorting genetic algorithm II (NSGA-II) to reproduce the ignition delay times in shock tubes and major species concentrations in jet-stirred reactors (JSR) over low-to-high temperatures. In NSGA-II, the range of the rate constants was considered to ensure the reliability of the optimized mechanism. Moreover, an improved objective function was proposed to maintain the faithfulness of the optimized mechanism to the original reaction mechanism, and a new method was presented to determine the optimal solution from the Pareto front.

Due to the increasing consumption of fossil fuels, alternative fuels in internal combustion engines have attracted a lot of attention in recent years. Ethanol is the most common alternative fuel used in spark ignition (SI) engines due to its advantages of biodegradability, positively impacting emissions reduction as well as octane number improvement. Meanwhile, acetone is well-known as one of the industrial waste solvents for synthetic fibers and most plastic materials. In comparison to ethanol, acetone has a number of more desirable properties for being a viable alternative fuel such as its higher energy density, heating value and volatility.

The combustion of cylinder lubricating oil (called as cylinder oil for short) is one of the major sources of PM emissions of low-speed 2-stroke marine diesel engines. For pre-mixed combustion low-speed 2-stroke marine gas engines, the auto-ignition of cylinder oil might result in knock or more hazard abnormal combustion - pre-ignition. Evaporation is a key sub-process of the auto-ignition process of cylinder oil droplets. The evaporation behavior has a profound impact on the auto-ignition and combustion processes of cylinder oil droplets, and a great influence on engine combustion performance and emission characteristics. This paper applied an oil suspending apparatus to investigate the evaporation behavior of cylinder oil droplets and base oil droplets. The effects of ambient temperatures on the evaporation process were measured and analyzed. The results indicate that the evaporation of cylinder oil includes heating, evaporating, pyrolysis, and polymerization.

In order to comply with the stringent emission regulations, many researchers have been focusing on diesel-compressed natural gas (CNG) dual fuel operation in compression ignition (CI) engines. The diesel-CNG dual fuel operation mode has the potential to reduce both the soot and NOx emissions; however, the thermal efficiency is generally lower than that of the pure diesel operation, especially under the low and medium load conditions. The current experimental work investigates the potential of using diesel-1-butanol blends as the pilot fuel to improve the engine performance and emissions. Fuel blends of B0 (pure diesel), B10 (90% diesel and 10% 1-butanol by volume) and B20 (80% diesel and 20% 1-butanol) with 70% CNG substitution were compared based on an equivalent input energy at an engine speed of 1200 RPM. The results indicated that the diesel-1-butanol pilot fuel can lead to a more homogeneous mixture due to the longer ignition delay.

A large eddy simulation approach and different breakup models are used to analyze fuel injection and atomization processes in a constant volume combustion bomb. The study is focused on the influences of the subgrid turbulent kinetic energy, especially the source term induced by the fuel spray, on the droplet movement and spray characteristics. Furthermore, the influence of different subgrid scale (SGS) models, including the constant coefficient and dynamic Smagorinsky models, WALE model and the K-equation turbulent energy transport model, on fuel sprays and the turbulent dispersion of droplets are examined. Factors affecting the fuel spray are discussed based on numerical computations for various operating conditions and are compared with experimental data.

Multi-dimensional models coupled with a reduced chemical mechanism were used to investigate the effect of fuel on exergy destruction fraction and sources in a reactivity controlled compression ignition (RCCI) engine. The exergy destruction due to chemical reaction (Deschem) makes the largest contribution to the total exergy destruction. Different from the obvious low temperature heat release (LTHR) behavior in gasoline/diesel RCCI, methanol has a negative effect on the LTHR of diesel, so the exergy destruction accumulation from LTHR to high temperature heat release (HTHR) can be avoided in methanol/diesel RCCI, contributing to the reduction of Deschem. Moreover, the combustion temperature in methanol/diesel RCCI is higher compared to gasoline/diesel RCCI, which is also beneficial to the lower exergy destruction fraction. Therefore, the exergy destruction of methanol/diesel RCCI is lower than that of gasoline/diesel RCCI at the same combustion phasing.

Butanol, which is a renewable biofuel, has been regarded as a promising alternative fuel for internal combustion engines. When blended with diesel and applied to pilot ignited natural gas engines, butanol has the capability to achieve lower emissions without sacrifice on thermal efficiency. However, high blend ratio of butanol is limited by its longer ignition delay caused by the higher latent heat and higher octane number, which restricts the improvement of emission characteristics. In this paper, the potential of increasing butanol blend ratio by adding hot exhaust gas recirculation (EGR) is investigated. 3D CFD model based on a detailed kinetic mechanism was built and validated by experimental results of natural gas engine ignited by diesel/butanol blends. The effects of hot EGR is then revealed by the simulation results of the combustion process, heat release traces and also the emissions under different diesel/butanol blend ratios.

In this work, large eddy simulation (LES) with a K-equation subgrid turbulent kinetic energy model is implemented into the CFD code KIVA3V to study the features of liquid fuel spray and combustion using gradually varying grid in a constant volume chamber. The characteristic time-scale combustion model (CTC) incorporating a turbulent timescale is adopted to predict the combustion process and the SHELL auto-ignition model is used to predict auto-ignition. Combustion is also simulated using Parallel Detailed Chemistry with Lu's n-heptane reduced mechanism (58 species), which has been added into the KIVA3V-LES code. The computational results are compared with Sandia experimental data for non-reacting and reacting cases. As a result, LES can capture the complex structure of the spray and temperature distribution as well as the trend of ignition delay and flame lift-off length variations. Better results are obtained using the Parallel Detailed Chemistry than the CTC model.

This paper inverstigates a new way of conical spray for medium speed D. I. diesel engine, with which three different construction injectors were used. The feature of conical spray and fuel-air mixture formation were observed by means of schlieren photograph technique. The main result is that the cone top angle of conical injector has influence on formation of fuel-air mixture and performance of engine. The results of test on a single-cylinder engine show the premixed combustion phase was possessed of a large proportions of the whole combustion period, which was become a leading feature. The increasing interest in study of diesel engine combustion is caused by achieving even more stringent emission standards and greatly improving the fuel economy. From present status of this research the traditional combustion system which with orifice nozzel has already exposed some inherent drawbacks.