Search Results

In this paper, a three-dimensional (3D) microstructure-based finite element modeling method (i.e., extrinsic modeling method) is developed, which can be used in examining the effects of porosity on the ductility/fracture of Mg castings. For this purpose, AM60 Mg tensile samples were generated under high-pressure die-casting in a specially-designed mold. Before the tensile test, the samples were CT-scanned to obtain the pore distributions within the samples. 3D microstructure-based finite element models were then developed based on the obtained actual pore distributions of the gauge area. The input properties for the matrix material were determined by fitting the simulation result to the experimental result of a selected sample, and then used for all the other samples’ simulation. The results show that the ductility and fracture locations predicted from simulations agree well with the experimental results.

The introduction of carbon fiber reinforced polymer (CFRP) composites to structural components in lightweight automotive structures necessitates an assessment to evaluate that their crashworthiness dynamic response provides similar or higher levels of safety compared to conventional metallic structures. In order to develop, integrate and implement predictive computational models for CFRP composites that link the materials design, molding process and final performance requirements to enable optimal design and manufacturing vehicle systems for this study, the dynamic mechanical response of unidirectional (UD) and 2x2 twill weave CRFP composites was characterized at deformation rates applicable to crashworthiness performance. Non-standardized specimen geometries were tested on a standard uniaxial frame and an intermediate-to-high speed dynamic testing frame, equipped with high speed cameras for 3D digital image correlation (DIC).

High-strength aluminum alloys such as 7075 can be formed using advanced manufacturing methods such as hot stamping. Hot stamping utilizes an elevated temperature blank and the high pressure stamping contact of the forming die to simultaneously quench and form the sheet. However, changes in the thermal history induced by hot stamping may increase this alloy’s stress corrosion cracking (SCC) susceptibility, a common corrosion concern of 7000 series alloys. This work applied the breaking load method for SCC evaluation of hot stamped AA7075-T6 B-pillar panels that had been artificially aged by two different artificial aging practices (one-step and two-step). The breaking load strength of the specimens provided quantitative data that was used to compare the effects of tensile load, duration, alloy, and heat treatment on SCC behavior.

Weld lines can significantly reduce ultimate tensile strength (UTS) and fracture strain of talc filled polypropylene (PP). In this paper, two different injection molding tests were completed. First, an injection mold with triangular inserts was built to study the influence of meeting angles on material properties at the weld line region. Tensile samples were cut at different locations along the weld line on the injection molded plaques. The test results showed that both UTS and fracture strain increase when the sample locations are away from the insert. This trend is attributed to different meeting angles. Second, standard ISO tensile bars with and without weld line were injection molded to identify the size of the weld line affected zone. A FEA model was built in ABAQUS, where the tensile sample was divided into two different regions, the solid region and the weld line affected region.

Fuel economy and federal safety regulations are driving automotive companies to use Dual Phase and other Advanced High Strength Steels (AHSS) in vehicle body structures. Joining and assembly plays a crucial role in the selection of these steels. Specifications are available for the resistance spot welding (RSW) of lower strength sheet steels, covering many aspects of the welding process from the stabilization procedure to endurance testing. Currently, specifications in the automotive industry for RSW with AHSS are limited. It is well known that welding of a thickness ratio greater than 1:2 poses a challenge. To utilize thinner gauge AHSS panels on body-in-white, welding schedules to join the thin to thick sheet steel stack-up are needed. Most of the existing published work was conducted on uncoated sheets and welded to the same thickness.

The automotive industry is in constant pursuit of alternative materials and processes to address the ever changing needs of their customer and the environment. This paper presents findings from a study using a laser hybrid process (laser with MIG) to join aluminum-silicon coated boron steel (USIBOR). In this report the influence of heat from the laser hybrid welding process and its effect on the coated boron steel is discussed. In order to understand the affect from laser hybrid joining process, bead on plate experiments were conducted using 1.0 mm, 1.6 mm and 2.0 mm thick coupons. Further, two lap joint configurations were also investigated using the 1.6 mm and 2.0 mm thick coupons. Based on the test results, a significant reduction in tensile strength was observed at the Heat Affected Zone (HAZ).

In this study, the Gleeble test was used to investigate the effect of cooling time, which is an indication of welding heat input, on fracture toughness at the simulated HAZ of different test materials, including one mild steel and three DP600 steels from three different suppliers. One of the important findings is that the three DP600 steels have similar tensile properties and similar base metal microstructures. After different simulated welding thermal cycles, however, the microstructure, the microhardness and thus the fracture toughness of the simulated HAZ of the steels showed significant variations among the steels tested, which indicates that DP600 steels from different suppliers can have different responses to the welding heat input.

Spot weld fatigue performance of dual phase steels is of great interest due to much higher fatigue strength of its base steel. In this study, 0.8mm DP500-EG and 1.4mm DP600-GI were tested for both tensile shear and cross tension conditions. For comparison, tensile shear test was also conducted for 1.6mm HSLA350-GI and 0.8mm DQSK-GI. Although fatigue strength was different due to their different gages, by using the stress index, Ki, a parameter to describe the local stress condition, fatigue strength of all four steels merged to a narrow scatter band, indicating very little dependence of spot weld fatigue on the strength of the base steel. In addition, the effect of weld surface cracking on fatigue strength of dual phase steels is of concern due to their high strength, despite the fact that it can occur to any steels under conditions of high current or electrode misalignment.

The use of Friction Stir Welding (FSW) is a robust process to use in the assembly of aluminum automotive components. The advantages include: minimal distortion, higher tensile strength, lower costs and improved weld capability than other joining processes. Though a simple process, there are key parameters that must be carefully selected to optimize the weld. This paper will focus on the use of FSW to assemble extrusions into automotive components.

Failure behavior of spot welds is investigated under impact loading conditions. Three different impact speeds were selected to test both HSLA steel and mild steel specimens under combined opening and shear loading conditions. A test fixture was designed and used to obtain the failure loads of spot weld specimens of different thicknesses under a range of combined opening and shear loads with different impact speeds. Accelerometers were installed on the fixtures and the specimens for investigation of the inertia effects. Optical micrographs of the cross sections of failed spot welds were obtained to understand the failure processes in both HSLA steel and mild steel specimens under different combined impact loads. The experimental results indicate that the failure mechanisms of spot welds are very similar for both HSLA steel and mild steel specimens with the same sheet thickness. These micrographs show that the sheet thickness can affect the failure mechanisms.

Residual stresses in metals are caused by a number of processes such as inhomogeneous deformation, phase changes and temperature gradients. This investigation focuses on the residual stresses caused by plastic deformation of automotive metals. Such stresses are responsible for part springback and shape distortion in many manufacturing and assembly processes. Tensile residual stresses may lead to stress cracking and, in some alloys, to stress corrosion cracking which may ultimately lead to premature product failure. The residual stress potential of metals can be evaluated by using the Split Ring Test Method. The test can be used to evaluate the effect of materials on residual stresses in cup drawing. Drawn cups are used because they produce large amounts of residual stresses and, therefore, increase measurement accuracy and reduce experimental error. A closed form analytical solution is used to estimate residual stresses in split rings taken from sections cut from the drawn cups.

With interest in improving vehicle quality and customer satisfaction, Ford Motor Company initiated an effort aimed at improving dent resistance of closure panels. An investigation of various means of product improvement led to the recognition of dual phase steels, due to their inherent formability and strain hardening attributes, as the most appropriate steel panel for outer panel applications. Ispat Inland's new Electro-galvanized dual phase steel DI-FORM 500 (henceforth referred to by the generic designation, DP500), which meets 500 MPa minimum tensile strength, was specifically designed to meet automotive exposed quality standards. This paper compares the dent resistance performance of automotive door assemblies manufactured with both Bake Hardenable 210 (BH210) and DP500 door outer panels. Results indicate the achievement of significantly improved outer panel dent resistance through the use of the DP500 product.

Aluminum extrusions are used in the automotive industry for body structure applications requiring cross-section design flexibility, high section stiffness, and high strength. Heat-treatable 6xxx series extrusion alloys have typically been used in automotive due to commercial availability, competitive cost, high strength, and impact performance. This paper presents a characterization study of mechanical properties of 6xxx series aluminum extrusions using digital image correlation (DIC). DIC has been used to capture spatial strain distribution and its evolution in time during material deformation. The materials of study were seamless and structural 6061 and 6082 extrusions. The alloys have been tensile tested using an MTS load frame with a dual optical camera system to capture the stereoscopic digital images. Notable results include the differing anisotropy of seamless and structural extrusions, as well as the influence of artificial aging on anisotropy.

Automotive manufacturers around the world are pushing towards the goal of better safety from their vehicles without compromising on the fuel economy. One of the very successful efforts in this direction is the hot forming technique that has been around for 30 years since Saab used it for the first time in 1986. Finite element simulations for this technique are of paramount importance to identify and optimize the process; as the steels used in hot stamping are sensitive to certain variables when heated that would otherwise cause very few disturbances in a normal cold forming process. The major contributor to the high strength of the stamped part is the phase transformation that it undergoes during the hot forming process. This paper investigates and identifies critical parameters through Finite Element Analysis (FEA) simulations.

To advance vehicle lightweighting, chopped carbon fiber sheet molding compound (SMC) is identified as a promising material to replace metals. However, there are no effective tools and methods to predict the mechanical property of the chopped carbon fiber SMC due to the high complexity in microstructure features and the anisotropic properties. In this paper, a Representative Volume Element (RVE) approach is used to model the SMC microstructure. Two modeling methods, the Voronoi diagram-based method and the chip packing method, are developed to populate the RVE. The elastic moduli of the RVE are calculated and the two methods are compared with experimental tensile test conduct using Digital Image Correlation (DIC). Furthermore, the advantages and shortcomings of these two methods are discussed in terms of the required input information and the convenience of use in the integrated processing-microstructure-property analysis.

In recent years, a special attention has been given to the environment protection, as evidenced by an increased commitment of governments and industries for a better use of energy and for reducing the levels of vehicle emissions (CO2). The use of renewable and bio-based plastics in the automotive sector is being considered as alternative solution to the conventional petroleum-based polymeric materials. In the present work, biobased polymer blends were formulated using two polyamides made from biorenewable resources. Polyamide 10,10 (PA1010) and polyamide 6,10 (PA610) were melt mixed in different compositions and the mechanical properties of the blends were investigated by tensile evaluations. The mechanical properties of the blends show intermediate values compared to the pure polymers. Significant improvements on these properties could be observed with the incorporation of PA610 in the blends.

Weld lines occur when melt flow fronts meet during the injection molding of plastic parts. It is important to investigate the weld line because the weld line area can induce potential failure of structural application. In this paper, a weld line factor (W-L factor) was adopted to describe the strength reduction to the ultimate strength due to the appearance of weld line. There were two engineering thermoplastics involved in this study, including one neat PP and one of talc filled PP plastics. The experimental design was used to investigate four main injection molding parameters (melt temperature, mold temperature, injection speed and packing pressure). Both the tensile bar samples with/without weld lines were molded at each process settings. The sample strength was obtained by the tensile tests under two levels of testing speed (5mm/min and 200mm/min) and testing temperatures (room temperature and -30°C). The results showed that different materials had various values of W-L factor.

Surfaces of A356 castings were treated by friction stir processing to reduce porosity and to create more uniform distributions of second-phase particles. Dendritic microstructures were eliminated in stir zones. The ultimate tensile strength, ductility, and fatigue life of the cast A356 was increased by friction stir processing. Tensile specimens of cast and friction stir processed metal were also given a T7 heat treatment. Higher tensile strengths and ductilities were also measured for these friction stir processed specimens.

Fretting fatigue was observed in standard cylindrical fatigue samples at the regions in contact with the grips of the test frames during fatigue testing for AlSi10Mg aluminum alloy produced by laser powder bed fusion process (L-PBF). The failure of the fatigue sample grips occurs much earlier than the failure of the gauge section. This results in a damaged sample and the sample cannot be reused to continue the test. This type of failure is rarely seen in materials produced by traditional manufacturing processes. In this study, X-ray residual stress analysis was performed to understand the cause of failure for L-PBF AlSi10Mg with the as-built surface condition. The result indicates that the fretting fatigue failure was caused by the strong tensile residual stress in the as-built state combining with the fretting wear between the sample and the grip. A few potential solutions to avoid the fretting fatigue failure were investigated.

Stress and strain measurement of high density polyethylene (HDPE) fuel tanks under dynamic loading is challenging. Motion tracking combined with computer vision was employed to evaluate the strain in an HDPE fuel tank being dynamically loaded with a crash pulse. Traditional testing methods such as strain gages are limited to the small strain elastic region and HDPE testing may exceed the range of the strain gage. In addition, strain gages are limited to a localized area and are not able to measure the deformation and strain across a discontinuity such as a pinch seam. Other methods such as shape tape may not have the response time needed for a dynamic event. Motion tracking data analysis was performed by tracking the motion of specified points on a fuel tank during a dynamic test. An HDPE fuel tank was mounted to a vehicle section and a sled test was performed using a Seattle sled to simulate a high deltaV crash. Multiple target markers were placed on the fuel tank.