Search Results

Using skirt-liner clearance and cylinder pressure measurements provided by Isuzu Motors, Ltd. of a production type gasoline automotive engine, a validation study was done of Ricardo's PISDYN code, which predicts the secondary motions and skirt liner elastohydrodynamic lubrication of pistons. Predictions using the computer code of the skirt liner clearance at two locations on the skirt were compared with measured results. Using the code, parametric studies were done. Very good qualitative and quantitative agreement was found for the baseline cases. In the parametric studies using the code only, the following were found: The predicted clearances were very sensitive to variation in cold minimum clearance. The effect of cylinder induced pressure deformation was significant, especially near the point of peak cylinder pressure. Increasing the cylinder pressure increased the peak clearances. Changing the asperity roughness height affected the clearances near a point of asperity contact only.

This paper offers a brief explanation of Isuzu Transport Auto Control (I-TAC), a system used to accurately collect and control information in-transit. I-TAC was developed as a means to meet needs for transportation by truck.

Supercharging system is obviously a necessary technology for heavy duty vehicular diesel to meet future stringent emission regulation as well as to improve fuel consumption characteristics. Although the conventional exhaust turbocharger system improves fuel consumption, there are some problems such as having a difficulty in improving starting acceleration and smoke emission characteristic because the response of an exhaust supercharger is not enough. On the other hand, the conventional mechanical supercharging system seems to be a quite effective aid for acceleration ability. However, it does not satisfy demand for low fuel consumption characteristic.

The growing need for improved fuel economy is a global challenge due to continuously tightening environmental regulations targeting lower CO2 emission levels via reduced fuel consumption in vehicles. In order to reach these fuel efficiency targets, it necessitates improvements in vehicle transmission hardware components by applying advanced technologies in design, materials and surface treatments etc., as well as matching lubricant formulations with appropriate additive chemistry. Axle lubricants have a considerable impact on fuel economy. More importantly, they can be tailored to deliver maximum operational efficiency over specific or wide ranges of operating conditions. The proper lubricant technology with well-balanced chemistries can simultaneously realize both fuel economy and hardware protection, which are perceived to have a trade-off relationship.

Every year the trucking industry demands lighter weight and lower cost truck components. But it is very difficult to achieve both these targets. This paper describes the example of a suspension system design which was conducted by computer simulation, so called CAE. The computer simulation by FEM was used completely to decide the detailed shape of each part. This paper also introduces a casting method to strengthen the aluminum alloy cast using high pressure during casting. By using this method, products have a precise metallographic structure. As a result, both the development cost and period were reduced by over the half the time required of the current system and lighter and strong parts were created.

When a heavy duty truck with 2 rear axles is turning a curve at slow speed, a large side bending force to the chassis frame occurres as vehicle turning radius becomes smaller. In the past, the stress produced by side bending forces was little analyzed. By our research work of FEM, side bending stress of heavy duty truck could be analyzed accurately.

Recently engin output and vehicle speed are much improved and there received much requests for better brake system with high performance and safety. In order to meet these reguests research work was initiated to develop new retavder system as auxiliary brake, and new compact & light weight retarder without requiring electricity consumption was successfully developed by using very strong parmanent magnet of Nd-Fe-B base for the first time in the world. This new retarder was marketed in the last January for the heavy duty truck followed medium duty tyuck in this April. This new retarder well matched with market needs has been highly commented upon beyond engineer expectation, and it is believed that this new system will be popularized very rapidly in Japan.

GVW 20 ton class cargo trucks were mainly powerd by L6 turbocharged engines ISUZU 6SD1TC and ISUZU 6RB1TC, and this time new 6WA1TC turbocharged engine with intercooler as a successor to 6RB1TC went into production in July 1992. In the recent cargo vehicle market in Japan, demand is increasing for higher out-put power, light weight, long service life, high reliability and low fuel consumption. Under such circumstances special engineering attention was paid to exhaust emissions and noise regulations which are expected to become even stricter in future. The basic engine structure consists of an OHC 4-valve type cylinder head and a ladder frame type cylinder block which satisfies the requirements for the high out-put power, low fuel consumption and light weight. Also, adopted are various variable structures such as a high pressure fuel injection pump with a variable injection timing and rate control device, variable swirl system and variable geometry turbocharger.

There is ever an increasing need for weight reduction and high performance of engine (clean smoke and improving fuel economy) To achieve this, recently aluminum castings are used for engine parts such as cylinder heads that construct combustion chamber and are required thermal resistance. This paper describes thermal fatigue tests of aluminum castings that are made under various conditions of cooling rate during solidification, heat treatment, and chemical compositions. It further investigates the influence of material (such as cooling rate, chemical conmposition and heat treatment) and mechanical properties (such as σB, δ, E ) on thermal fatigue life of aluminum castings.

Torsional dampers have been attached to engine crankshafts only for the control of the crankshaft torsional vibrations. However, a torsional damper is a mass-spring system of three-dimensions, so the torsional damper could exert some influence on the three-dimensional vibrations of the crankshaft system. Since the inertia ring of the torsional damper has moments of inertia and it rotates with the crankshaft, gyroscopic vibrations of the inertia ring can also be generated. For a V-type ten-cylinder diesel engine (V- 10, ϕ119 × 150), the three-dimensional vibrations of the crankshaft system were calculated by the dynamic stiffness matrix method, taking account of the influence of the gyroscopic vibrations of the inertia ring of the torsional damper. The dynamic bending stresses were measured at the fillets of both the No.1 crank journal and the No.1 crank pin in the No.1 crank throw plane.

Application of alternate fuels to diesel engine is much desired. A new and unique dual-fuel injection system has been developed for high speed automotive diesel engines. This system has two features. One is that alternate fuels such as methanol, ethanol and biomass, are directly inducted into the fuel injection pipe through one-way check valve under pressure, and blended fuels are simultaneously injected into the combustion chamber. The other is that various kinds of fuel can be easily adapted to this system not dependent upon the fuel properties such as viscosity. Using a single cylinder direct injection diesel engine and ethanol as an alternate fuel, injection characteristics and exhaust gas emissions were investigated. The results showed that ethanol could replace up to 50% of diesel fuel while keeping the normal engine operating stability. A better fuel economy was also obtained by applying both higher compression ratio and advanced injection timing.

The P’UP has been on the markets worldwide since 1972, both in Japan and overseas, including for the U.S., in which case, with model designation as the Chevrolet LUV. In 1980, for the first time since its market introduction, it was fully remodelled with detail improvements reflected thereon in every aspect. This new model continues to be on the U.S. market as the Chevrolet LUV as it has been, but, beginning from spring of 1981, the similar model has been introduced to the market by the American Isuzu Motors Inc. (AIM) as the Isuzu P’UP. Taking this opportunity, a diesel version has been added to its model lineup. The diesel engine mounted on this version features its 20 to 30% better fuel efficiency over its gasoline counterpart. In the first half of this paper, the engineering concepts of its full remodelling and their onvehicle reflection will be introduced.

Equations of motion with six degrees of freedom are composed of detailed dimensions of vehicle, suspension, steering and tire, which must be determined at the designing stage. Particularly, in the dyamics of suspension system, the hypothesis of fixed roll axis are excluded. And, instead, the effect of side force which affects rolling and vertical motion of the vehicle is introduced on the basis of geometrical variation of the tire's contact points. In addition, a number of equations including the cornering force of tire are treated in nonlinear method, with the effect of driving and braking forces being taken into account at the same time. This analysis has enabled strict interpretation of cornering characteristics. However this article is devoted mainly to the analysis of various phenomena which take place in critical situations responsible for accidents in cornering, resultant from spin-out, drift-out, wheel-lift (jack-up) and roll-over.

This paper describes about Hill Starting Aid (HSA) system for mechanical transmission vehicle designed to retain braking force of service brake after vehicle stops and to release this braking force automatically at the time of vehicle starting. By this system, the driver can start on slope as easy as starting on level road, because it relieved driver of operating hand brake lever and quick movement of his right foot from brake pedal to accelerator pedal. So, this system alleviates fatigue of drivers and also efficient for inexperienced drivers. As this system is basically brake force holding system, it is effective for prevention of successive collision from behind too. In this way. HSA system is very suitable for Japanese traffic condition which there are many slopes and heavy traffic in city.

In order to meet the demands for reduced emissions and improved fuel consumption, a subport-type variable swirl system (Isuzu Variable Electronic Economy Swirl, or IVES) was developed by Isuzu for medium- and heavy-duty direct-injection-type diesel engines. The main characteristics of IVES are: (1) It is simple in structure and only minor changes to the cylinder head are required. (2) Modular design is possible for three different swept volume engines due to the use of a common actuator and sensor. (3) The problem of air flow coefficient drop when swirl is varied has been successfully eliminated.

In fleet uses, heavy-duty trucks with turbo, inter-cooled engines are popular in Japan. These trucks usually experience congested traffic and/or frequent road grade change in expressways. As a result, frequent vehicle speed and engine load fluctuations are observed. This paper describes the typical, on road driving data from the field and presents one sample of engine control optimization for better fuel economy in actual road conditions.

Experiment results were compared with computation analysis results for torsional vibration on a crankshaft system with/without a torsional viscous damper on a six-cylinder in-line type turbocharged diesel engine and a V type ten-cylinder naturally-aspirated diesel engine respectively. At first, the boundary conditions for boundary element method (BEM) model were determined to estimate the torsional stiffness of the crank-throws of the crankshafts. Then, the estimated stiffness was used to calculate the natural frequencies of the torsional vibration without the damper by dynamic stiffness matrix method. As a result, the calculated natural frequencies approximately agreed with the measured ones. Finally, the torsional vibration with the damper was analyzed by using the dynamic stiffness matrix method and complex viscous damping coefficients for the damper. The calculated torsional amplitudes and resonant engine speeds agreed with the experiment results.