Refine Your Search

Search Results

Viewing 1 to 6 of 6
Technical Paper

Design and Analysis of Hybrid Metal Matrix Composite Connecting Rod via Stir/Squeeze Casting Route

2019-10-11
2019-28-0113
The connecting rod was manufactured by forging process for enhancing high tensile and compressive load so that it was followed by the machining process and suite the IC engine as a part of the component. The main intern of our proposed work is to manufacture a two set of composites specimen of A356 alloy with reinforcement of 5 wt.% silicon carbide and 10 wt.% flyash processed through two different techniques like stir casting and stir cum squeeze casting route and obtain better mechanical properties. Further, the same properties were taken for modeling and analysing of the developed connecting rod model. Due to the commercial demand, the hybrid composite materials take a vigorous role in the analysis part of the connecting rod model. The FEA analysis is done on the connecting rod for a180cc engine by using Ansys 18.1. The static analysis is done by considering four different cases by altering material library property.
Technical Paper

Investigation of Dry Sliding Wear Behavior of AA8011 Reinforced with Zirconium Oxide and Aluminium Oxide Hybrid Composites Processed through Multi-Direction Forging

2019-10-11
2019-28-0057
The Cardinal goal of this research work is to fabricate hybrid composites of AA8011 with reinforcement particles of Zr2O3 and Al2O3 which was taken in equal (5wt%) weight percentage. The hybrid composites were cast in a square shape (50x50x50 mm size) under the optimal stir casted process parametric condition, further, it was taken for the forging process. The prepared specimens were induced for uni-direction (x), bi-direction (x and y) and multi-direction (x,y, and z) forging route and the response of microhardness of 53, 68, 81 and 96 VHN were obtained respectively due to microstructural phase changes with an even distribution of particles in the matrix. Thus, the tribological properties of prepared specimens were tested using pin-on-disc Tribometer at room temperature under dry sliding condition of load 5,10,15,20 N and by adjusting the sliding speed as 266 and 531 rpm respectively.
Technical Paper

Design and Analysis of De-Lavel Restrictor with Throttle Body for Formula Vehicle

2019-10-11
2019-28-0009
The restrictor is a component which controls the mass flow of air passing to the engine. The proposed work focuses on design and analysis of air intake restrictor of Duke 390cc engine which is used in formula vehicles. As an constrain of this system, the air flows through a single circular throat of diameter 20mm. In past decades conventional venture nozzles were used as a restrictor but it leads to nominal press drop. A de lavel nozzle is a tube pinched in the middle, making an asymmetric hourglass shape. It is used to accelerate a higher supersonic speed in the axial direction. The main objective is to utilize De-Laval Nozzle for the minimal pressure drop. The change in pressure will increases the engine power output. The analysis is done by varying design conditions such as three levels of convergent (12,14 and 16 degrees) and three levels of divergent angles (4, 6 and 8 degrees) are taken into consideration.
Technical Paper

The Effect of Print Orientation and Infill Density for 3D Printing on Mechanical and Tribological Properties

2020-09-25
2020-28-0411
The 3D Printing (3DP) technology due to its greatest strength, resistance to wear and corrosion to oxidizing agents and has good temperature resistance with durable one. The present article describes the effect of print orientation and infill density of 3DP route on mechanical and tribological properties of PETG filament. The 3DP parameters like layer thickness, slicing, speed, feed are kept as constant and by varying the print orientation (X, Y, Z) with infill density (50%, 75%, 100%) was printed to check the effect of it on mechanical and tribological properties like hardness, impact strength, ultimate tensile strength, flexural strength, wear rate and coefficient of friction. The results shows that all the tested mechanical and tribological properties increase by around 30-60% when the orientation is in the X direction at infill density of 100%.
Technical Paper

Assessment of the Metallurgical and Mechanical Properties of Stir cum Squeeze Cast A356 with 5wt. % SiC and x wt. % Flyash Hybrid Composites

2020-09-25
2020-28-0397
The forged connecting rod and pin experience a large amount of stresses due to cyclic load for a long period of time induced by the reciprocating movement of the piston. The proposed work focused to produce lightweight composites with high strength using waste flyash and simple manufacturing process. In this context, the proposed experimental work was formulated to develop aluminium alloy hybrid metal matrix composite of A356 alloy with silicon carbide and flyash processed through stir cum squeeze casting process under optimal parametric condition. The samples were subjected to varying flyash content of 0, 5, 10wt.% and SiC of 5wt.% kept constant. Responses like metallography, hardness, impact strength, flexural strength, fatigue strength were observed for the manufactured hybrid composites. There was a significant improvement in the properties with a higher weight percentage addition of 10wt.% flyash and 5wt.% SiC with A356 hybrid composites.
Technical Paper

Experimental Studies on Weldability of Oil Hardening Non Shrinking Die Steel

2020-09-25
2020-28-0424
The Oil Hardening Non Shrinking (OHNS) die steel refers to a variety of carbon and alloy steels that are particularly well-suited for making tools. Though these steels are weldable, there is risk of crack formation. But, this can be avoided with convinced specifications like pre heating, proper choice of electrode etc., In the present work, OHNS die steel is welded with three different electrodes. The chosen electrodes were mild steel electrode, E312-16 chromium based electrode and E-NiCrFe-3 nickel based electrode. The OHNS steel is welded with these three electrodes and the welded specimens were examined for hot cracking tendency and mechanical properties of the joint. The hot cracking tendency was assessed by Houldcroft’s weldability test (Fishbone test). All the three electrodes proved the good results in terms of hot crack resistance and the specimen welded with E312-16 chromium based electrode provides good mechanical properties.
X