Search Results

Toyota Motor Corporation has developed the new compact-class hybrid vehicle (HV). This vehicle incorporates Toyota Hybrid System II (THS-II) to improve fuel efficiency. For this system we have developed a new power control unit (PCU) that features size reduction, light weight, and high efficiency. We have also improved the ability to mass produce these units with the expectation of rapid popularization of HV. The PCU, which plays an important role in THS-II, is our main focus in this paper. Its development is described.

Further fuel economy improvement of the internal combustion engine is indispensable for CO2 reduction in order to cope with serious global environmental problems. Although lowering the viscosity of engine oil is an effective way to improve fuel economy, it may reduce the wear resistance. Therefore, it is important to achieve both improved fuel economy and reliability. We have developed new 0W- 8 engine oil of ultra-low viscosity and achieved an improvement in fuel economy by 0.8% compared to the commercial 0W-16 engine oil. For this new oil, we reduced the friction coefficient under boundary lubrication regime by applying an oil film former and calcium borate detergent. The film former increased the oil film thickness without increasing the oil viscosity. The calcium borate detergent enhanced the friction reduction effect of molybdenum dithiocarbamate (MoDTC).

New engine controls have been developed for the turbocharged Lexus NX200t to improve driving power by reducing engine torque output lag. Drive power management functions have been centralized in an integrated drive power control system. The newly developed controls minimize the potential reduction in drivability associated with the adoption of a turbocharged engine while improving fuel efficiency. General driveability issues commonly associated with a turbocharged engine include sudden increases in drive power due to the response lag of the turbocharger, and higher shifting frequencies if this response lag triggers a disturbed accelerator operation pattern by the driver. The developed technologies detect and control sudden increases in drive power to create the optimum drive power map, and reduce unnecessary shifts even if the driver's accelerator operation is disturbed.

One way to improve the fuel efficiency of HVs is to reduce the losses and size of the Power Control Unit (PCU). To achieve this, it is important to reduce the losses of power devices (such as IGBTs and FWDs) used in the PCU since their losses account for about 20% of the total loss of an HV. Furthermore, another issue when reducing the size of power devices is ensuring the thermal feasibility of the downsized devices. To achieve the objectives of the 4th generation PCU, the following development targets were set for the IGBTs: reduce power losses by 19.8% and size by 30% compared to the 3rd generation. Power losses were reduced by the development of a new Super Body Layer (SBL) structure, which improved the trade-off relationship between switching and steady-state loss. This trade-off relationship was improved by optimizing the key SBL concentration parameter.

In order to improve the fuel efficiency of Hybrid Electric Vehicles (HEVs), it is necessary to reduce the size and power loss of the HEV Power Control Units (PCUs). The loss of power devices (IGBTs and FWDs) used in a PCU accounts for approximately 20% of electric power loss of an HEV. Therefore, it is important to reduce the power loss while size reduction of the power devices. In order to achieve the newly developed PCU target for compact-size vehicles, the development targets for the power device were to achieve low power loss equivalent to its previous generation while size reduction by 25%. The size reduction was achieved by developing a new RC-IGBT (Reverse Conducting IGBT) with an IGBT and a FWD integration. As for the power loss aggravation, which was a major issue due to this integration, we optimized some important parameters like the IGBT and FWD surface layout and backside FWD pattern.

Toyota Motor has developed a new compact class hybrid vehicle (HV). This vehicle incorporates a new hybrid system to improve fuel efficiency. For this system, a new power control unit (PCU) has been developed that is downsizing, lightweight, and high efficiency. It is also important to have a highly adaptable function that can be applied to various car models. This paper describes the development of PCUs that play an important role in new systems.

Automobile manufactures need to adopt new technologies to meet global CO2 (carbon dioxide) emission regulations and better fuel efficiency demands from customers. Also, the production cost should be as low as possible for an affordable vehicle. Therefore, it is advantageous for OEMs to develop fuel efficient technologies which can be controlled by software without additional hardware costs. The coasting control is a fuel efficiency improvement technology that can be implemented by the change of vehicle software only. The coasting control is a technology that reduces the driving resistance (Deceleration) when the driver releases the gas pedal. This technology leads to reducing the energy required for the vehicle to drive and results in improving the real-world fuel economy. In an internal combustion engine (ICE) vehicle, the coasting state is achieved by changing the gear to neutral, and the effect has been discussed and clarified by many previous studies.

Toyota has developed a new Hybrid (HV) transaxle P810 for Mid-Size SUVs to improve fuel efficiency and power performance. The transaxle was developed based on Toyota's new development strategy - Toyota New Global Architecture (TNGA). By adopting technologies to shorten overall length of the transaxle, installation into the same engine compartment of Mid-Size sedans have been realized while also improving the motor output. This paper will introduce technologies regarding the new mount structure for shortening overall length, and furthermore, noise reduction related to this mount structure.

Recently, global warming and energy security have received significant attention. Thus an improvement of the vehicle fuel economy is strongly required. For engines, one effective way is to improve the engine thermal efficiency. Raising compression ratio [1] or turbo charging technologies have potential to achieve high thermal efficiency. However knock does not allow the high thermal efficiency. Knock depends on the fuel composition and the pressure and temperature history of unburnt end-gas [2-3]. For fuels, RON is well known for describing the anti knock quality. High RON fuels have high anti knock quality and result in higher thermal efficiency. This paper investigates the impact of high RON fuels on the thermal efficiency by using high compression ratio engine, turbo charged engine, and lean boosted engine [4]. Finally, it is shown that the high thermal efficiency can be approached with high RON gasoline and ethanol.

Recent engine systems have become complex due to the requirements of fuel efficiency, exhaust gas emission control and good drivability. To decrease engine development period, model-based development has been adopted [1]. For torque-based vehicle control, engine torque estimation models are necessary. Simple mean-value torque models are available but these models require large amount of test data for development and validation. In addition, they cannot estimate transient torque precisely. On the other hand, complex physical models require considerable time for modeling and simulation. In order to decrease modeling time and retain model accuracy, the Wiebe function is utilized to calculate the heat release rate.

An SAE 5W-20 ILSAC GF-2 gasoline engine oil, which improves vehicle fuel efficiency by more than 1.5% relative to conventional SAE 5W-30 gasoline engine oils, was newly developed. And the target that 1.5% fuel efficiency improvement remains more than 10,000km was also achieved. The viscosity of this oil was optimized to satisfy both fuel economy and anti-wear performances. MoDTC and thiadiazole were added to achieve the target.

In recent years, attention has been focused on a hybrid vehicle capable of substantial reductions in CO2 exhaust emissions. This paper describes the newly developed 1.8-liter 2ZR-FXE gasoline engine for use with a hybrid system for compact vehicles, which effectively combines higher driving performance with higher fuel efficiency. This engine was based on the 1.8-liter 2ZR-FE engine with outstanding performance and fuel efficiency. This engine has achieved high thermal efficiency by using the high-expansion ratio cycle “Atkinson cycle”, as with the previous 1NZ-FXE engine. Additionally, a new cooled Exhaust Gas Recirculation (EGR) system and electric water pump were adopted to further improve fuel efficiency. A high efficiency cooler was used to cool the EGR gas, which enabled the introduction of the EGR gas at high load conditions, and exhaust gas temperature was reduced.

Various issues must be resolved before sustainable mobility can be achieved, the most important of which are reacting to energy supply and demand, and lowering CO2 emissions. At present, the fact that the vast majority of vehicles run on conventional oil is regarded as a problem for which Toyota Motor Corporation (TMC) is developing various technological solutions. Fuel cell (FC) technology is one of the most promising of these solutions. A fuel cell is an extremely clean device that uses hydrogen and oxygen to generate power without emitting substances like CO2, NOx, or PM during operation. Its energy efficiency is high and it is widely expected to form the basis of the next generation of powertrains. Since 1992, TMC has been working to develop the main components of fuel cell vehicles, including the fuel cell itself, and the high pressure hydrogen tank and hybrid systems.

Spark ignition direct injection (SIDI) engines have the potential to realize significant thermal efficiency improvements compared to conventional port fuel injection engines. The effects of fuel properties on efficiency and emissions have been investigated in a prototype of an Avensis Wagon equipped with a 2.0 liter, 4 cylinder spark ignition, direct injection (SIDI) engine designed to meet US 2000 emission standards. The vehicle employed a close coupled three-way catalyst and a NOx storage and reduction catalyst. Seven matrix fuels were blended to the same RON with varying levels of aromatics, olefins, ethanol, and volatility. Relative thermal efficiency, fuel economy, and tailpipe emissions were measured for the matrix fuels and a base fuel under the FTP LA4 driving cycle. The engine was operated in a lean burn mode in light load condition for approximately half of the driving cycle.

It is important for vehicle concept planning to estimate fuel economy and the influence of vehicle vibration using virtual engine specifications and a virtual vehicle frame. In our former study, we showed the 1D physical power plant model with electrical starter, battery that can predict combustion transient torque, combustion heat energy and fuel efficiency. The simulation result agreed with measured data. For idling stop system, the noise and vibration during start up is important factor for salability of the vehicle. In this paper, as an application of the 1D physical power plant model (engine model), we will show the result of analysis that is starter shaft resonance and the effect on the engine mount vibration of restarting from idle stop. First, an engine model for 3.5L 6cyl NA engine was developed by energy-based model using VHDL-AMS. Here, VHDL-AMS is modeling language registered in IEC international standard (IEC61691-6) to realize multi physics on 1D simulation.

Introducing effective technologies to reduce carbon emissions in the transport sector is a critical issue for automotive manufacturers to contribute to sustainable development. Unlike the plug-in electric vehicles (PEVs), whose effectiveness is dependent on the carbon intensity of grid electricity, the solar hybrid vehicle (SHV) can be an alternative electric vehicle because of its off-grid, zero-emission electric technology. Its usability is also advantageous because it does not require manual charging by the users. This study aims at evaluating the economic, environmental, and usability benefits of SHV by comparing it with other types of vehicles including PEVs. By setting cost and energy efficiency on the basis of the assumed technology level in 2030, annual cost and annual CO2 emissions of each vehicle are calculated using the daily mileage pattern obtained from a user survey of 5,000 people in Japan and the daily radiation data for each corresponding user.

Driveshafts are composed of a transmission side joint, wheel side joint, and shaft which connect the two joints. The Rzeppa type constant velocity joint (CVJ) is usually selected as the wheel side joint of a drive shaft for front wheel drive automobiles. Due to recent needs of fuel efficiency and lighter weight for vehicles, it is necessary to reduce the joint size and improve the efficiency of a CVJ. In order to reduce the weight, solving tribology details for long life under high contact pressure is an important issue for developing a CVJ. It is difficult to understand the characteristics of a contact surface, such as relative slip velocity or spin behavior, because the outer race, inner race, cage, and balls, act complicatedly and exchange loads at many points. Meanwhile, after joint endurance tests, ball spalling marks at pole of the ball are sometimes observed.

Toyota introduced the first generation Prius in 1997. The vehicle was conceived, designed and launched as a dedicated, mass-produced global hybrid vehicle platform, the first of its kind. The introduction of the 2nd and 3rd generation Prius (2003, 2009) saw vehicles with significantly improved performance, including fuel efficiency. The Prius Alpha (Japan/EU), launched in 2011, represented Toyota first foray with Li-ion battery in a strong hybrid configuration. For the Prius Alpha, the adoption of a compact Li-ion battery resulted in sufficient cabin space to allow a 3rd row of seats while maintaining high fuel efficiency. Before and after the launch of the Prius Alpha, an extensive list of tests was performed on the Li-ion battery pack, including electrical, electrochemical, mechanical, and safety. The evaluations were performed in the lab, in the field (demonstration fleets) and by acquiring vehicles used by customers.

Reducing the loss of the power control unit (PCU) in a hybrid vehicle (HV) is an important part of improving HV fuel efficiency. Furthermore the loss of power devices (insulated gate bipolar transistors (IGBTs) and diodes) used in the PCU must be reduced since this amounts to approximately 20% of the total electrical loss in an HV. One of the issues for reducing loss is the trade-off relationship with reducing voltage surge. To restrict voltage surge, it is necessary to slow down the switching speed of the IGBT. In contrast, the loss reduction requires the high speed switching. One widely known method to improve this trade-off relationship is to increase the gate voltage in two stages. However, accurate and high-speed operation of the IGBT gate control circuit is difficult to accomplish. This research clarifies a better condition of the two-stage control and designed a circuit that improves this trade-off relationship by increasing the speed of feedback control.

The renewed platform of the upcoming flagship front-engine, rear-wheel drive (FR) vehicles demands high levels of driving performance, fuel efficiency and noise-vibration performance. The newly developed driveline system must balance these conflicting performance attributes by adopting new technologies. This article focuses on several technologies that were needed in order to meet the demand for noise-vibration performance and fuel efficiency. For noise-vibration performance, this article will focus on propeller shaft low frequency noise (booming noise). This noise level is determined by the propeller shaft’s excitation force and the sensitivity of differential mounting system. In regards to the propeller shaft’s excitation force, the contribution of the axial excitation force was clarified. This excitation force was decreased by adopting a double offset joint (DOJ) as the propeller shaft’s second joint and low stiffness rubber couplings as the first and third joints.