Search Results

Diesel engines with relatively good fuel economy are known as an effective means of reducing CO₂ emissions. It is expected that diesel engines will continue to expand as efforts to slow global warming are intensified. Diesel particulate and NOx reduction system (DPNR), which was first developed in 2003 for introduction in the Japanese and European markets, shows high purification performance which can meet more stringent regulations in the future. However, it is poisoned by sulfur components in exhaust gas derived from fuel and lubricant. We then developed the sulfur trap DPNR with a sulfur trap catalyst that traps sulfur components in the exhaust gas. High purification performance could be achieved with a small amount of platinum group metal (PGM) due to prevention of sulfur poisoning and thermal deterioration.

Previous reports have already described the details of engine start-shock and the mechanism of vibration mechanism in a stationary vehicle. This vibration can be reduced by optimized engine and motor generator vibration-reduction controls. A prediction method using a full-vehicle MBD model has also been developed and applied in actual vehicle development. This paper describes the outline of a new method for the hybrid system of mechanical power split device with two motors that predicts engine start-shock when the vehicle is accelerating while the engine is stopped. It also describes the results of mechanism analysis and component contribution analysis. This method targets engine start-shock caused by driving torque demand during acceleration after vehicle take-off. The hybrid control system is modeled by MATLAB/Simulink. A power management and motor generator control program used in actual vehicles is installed into the main part of the control system model.

It is well understood that using lower viscosity engine oils can greatly improve fuel economy [1, 2, 3, 4]. However, it has been impossible to evaluate ultra-low viscosity engine oils (SAE 0W-12 and below) utilizing existing fuel economy test methods. As such, there is no specification for ultra-low viscosity gasoline engine oils [5]. We therefore developed firing and motored fuel economy test methods for ultra-low viscosity oils using engines from Japanese automakers [6, 7, 8]. This was done under the auspices of the JASO Next Generation Engine Oil Task Force (“TF” below), which consists mainly of Japanese automakers and entities working in the petroleum industry. Moreover, the TF used these test methods to develop the JASO GLV-1 specification for next-generation ultra-low viscosity automotive gasoline engine oils such as SAE 0W-8 and 0W-12. In developing the JASO GLV-1 specification, Japanese fuel economy tests and the ILSAC engine tests for evaluating engine reliability were used.

This research developed a new measurement technology for thermal analysis of the heat radiation from a hybrid transaxle case surface to the air and improved the heat radiation performance. This heat flux measurement technology provides the method to measure heat flux without wiring of sensors. The method does not have effects of wiring on the temperature field and the flow field unlike the conventional methods. Therefore, multipoint measurement of heat flux on the case surface was enabled, and the distribution of heat flux was quantified. To measure heat flux, thermal resistances made of plastic plates were attached to the case surface and the infrared thermography was used for the temperature measurement. The preliminary examination was performed to confirm the accuracy of the thermal evaluation through heat flux measurement. The oil in the transaxle was heated and the amount of heat radiation from the case surface was measured.

In this study, we combined a diesel engine with the Toyota Hybrid System (THS). Utilizing the functions of the THS, reducing engine friction, lowering the compression ratio, and adopting a low pressure loop exhaust gas recirculation system (LPL-EGR) were examined to achieve both low fuel consumption and low nitrogen oxides (NOx) emissions over a wide operating range. After applying this system to a test vehicle it was verified that the fuel economy greatly surpassed that of a conventional diesel engine vehicle and that NOx emissions could be reduced below the value specified in the Euro 6 regulations without DeNOx catalysts.

This paper provides an overview of automotive electronic systems put into products over the past decade, and describes automotive electronics which have been demonstrated in experimental cars. In addition, future electronic systems found to be promising for the practical use in coming years and the direction of development of electronics are also discussed, as an extention of the overview mentioned above.

The use of ceramic insulation to reduce engine heat loss and thus improve fuel economy was examined but found to be detrimental rather than advantageous. This paper analyzes the reasons and presents an alternative approach, namely minimizing the heat transfer area. Experiments were conducted to determine the effects of surface smoothness on BSFC, output torque, heat release rate and piston temperature. It was found that with a mirror-finished combustion chamber, heat loss is decreased and consequently engine output is raised, while fuel consumption is lowered. The percentage reduction in heat loss was ascertained by numerically simulating combustion and was confirmed by FEM analysis of piston thermal distribution.

This paper describes the preliminary development of an on-board integration network for vehicle dynamics. The underlying philosophy is explained and the basic requirements are set forth. A design conforming to these requirements is presented and the experiments conducted to optimise the physical layer are described. An original token passing protocol is proposed for the access method and evaluated in comparison with the contention method by means of a specially devised simulation system.

A high reliability and low cost temperature sensor for motor vehicle has been developed. The principle of measuring temperature is based on the NTC thermistor. And novel production techniques for sealing and electric connection are presented.

This research proposes an automatic measuring method for the impulse noise of the valve system in engine production line. This research is composed of the following two parts. (1) The most suitable method for indicating the impulse noise of the valve system - the representative characteristic values - is selected from the general measuring methods for impulse noise. As the result, the crest factor in the frequency band above 1kHz became optimal. (2) By detailed sensory characteristic analysis it was found that impulse noise can be heard better with increasing frequency and that there is little influence in the frequency band with the same frequency as the background noise. Thus the crest factor was obtained for each frequency, and the sensory test for the impulse noise of the valve system is deduced by this linear coupling. As the result of multiple reguression analysis, a high accuracy prediction equetion with a multiple correlation coefficient of 0.91 has been obtained.

A new automatic transmission, engineered from concept for “intelligent” and “anti-aging” (long life), has been designed and developed for TOYOTA's luxury passenger car, LEXUS LS400. This system, which has resulted in silky-smooth shift quality without changes in the long term, is composed of a transmission computer that interacts with engine computer, a number of sensors, an electronically controlled hydraulic unit with linear solenoid valves and assorted devices. As new control logic being developed with the aid of computer simulation to achieve distinction, the hydraulic and engine controls are combined in this system. There is a “feedback control”, where the clutch pressure is controlled according to the rate of acceleration and compensated for dispersion to applied pressure, engine torque and/or the coefficient of dynamic friction of clutches, and at the same time engine torque is reduced by retarding ignition timing.

A communication system that uses roadside beacons to broadcast road and traffic information and private messages to vehicles has been developed. The system, called Road/Automobile Communication System (RACS), was the result of a joint research project involving the Public Works Research Institute and 25 private-sector corporations. This paper contains an outline of RACS and of an onboard system developed by TOYOTA and presents the results of field tests conducted in the Tokyo area. The results not only verify the capability of the RACS system and the effectiveness of the in-vehicle equipment but also indicate the potential of such a beacon based network to improve traffic jam and driving safety whilst providing enhanced communication facilities without increasing radio-wave congestion.

This paper describes the Electro-Multivision map navigation software mounted in the Toyota Soarer (1991). The following functions are required of on-board map navigation software: 1. Indication of the exact position of the vehicle to the driver 2. Determination of the optimum path to the destination and presentation of this route to the driver in the simplest way 3. Accommodation of a wide variety of destinations and settings for different users The following gives some examples of how these functions are achieved and outlines the associated technologies. 1. Path finding and associated display technology Path finding algorithm and technology for displaying the calculated on the map; construction of a data base on CD-ROM 2. Technology for determination of the current position utilizing map matching and the global positioning system(GPS) A method with improved reliability based on two current position outputs obtained using map matching and the GPS and the mutual compensation method 3.

An on-board particulate matter (PM) sensor, consisting of a gas-permeable electrochemical cell with a porous yttria-stabilized zirconia solid oxide electrolyte, was developed to assist the on-board diagnostics (OBD) system of a vehicle. Exhaust is pumped from the anode side to the cathode side and PM deposited on the anode is instantly oxidized by the catalytic effects of the metal component of the electrode at temperatures higher than 350°C. The PM oxidation reaction occurs at the three-phase boundary between the anode, electrolyte and gas phase, and causes a slight change in the bulk average oxygen concentration, which produces electrochemical polarization by the difference in oxygen partial pressures between the anode and cathode. The developed PM sensor has a detection limit of 2 mg/m₃, at which level will enable PM detection in the OBD system according to the EURO VI regulation.

Fuel efficiency improvement measures are focusing on both cold and hot conditions to help reduce CO2 emissions. Recent technological trends for improving fuel economy such as hybrid vehicles (HVs), engine start and stop systems, and variable valve systems feature expanded use of low-temperature engine operation regions. Under cold conditions (oil temperature: approximately 30°C), fuel consumption is roughly 20% greater than under hot conditions (80°C). The main cause of the increased friction under cold conditions is increased oil viscosity. This research used the motoring slipping method to measure the effect of an improved crankshaft bearing, which accounts for a high proportion of friction under cold conditions. First, the effect of clearance was investigated. Although increasing the clearance helped to decrease friction due to the oil wedge effect, greater oil leakage reduced the oil film temperature increase generated by the friction.

ExxonMobil, Corning and Toyota have collaborated on an Onboard Separation System (OBS) to improve gasoline engine efficiency and performance. OBS is a membrane based process that separates gasoline into higher and lower octane fractions, allowing optimal use of fuel components based on engine requirements. The novel polymer-ceramic composite monolith membrane has been demonstrated to be stable to E10 gasoline, while typically providing 20% yield of ∼100 RON product when using RUL 92 RON gasoline. The OBS system makes use of wasted exhaust energy to effect the fuel separation and provides a simple and reliable means for managing the separated fuels that has been demonstrated using several generations of dual fuel test vehicles. Potential applications include downsizing to increase fuel economy by ∼10% while maintaining performance, and with turbocharging to improve knock resistance.

Detergent additives in automotive gasoline fuel are mainly designed to reduce deposit formation on intake valves and fuel injectors, but it has been reported that some additives may contribute to CCD formation. Therefore, a standardized bench engine test method for CCDs needs to be developed in response to industry demands. Cooperative research between the Petroleum Association of Japan (PAJ) and the Japan Automobile Manufacturers Association, Inc. (JAMA), has led to the development of a 2.2L Honda engine dynamometer-based CCD test procedure to evaluate CCDs from fuel additives. Ten automobile manufacturers, nine petroleum companies and the Petroleum Energy Center joined the project, which underwent PAJ-JAMA round robin testing. This paper describes the CCD test development activities, which include the selection of an engine and the determination of the optimum test conditions and other test criteria.

A slip-controlled lock-up clutch system Is very efficient in improving the fuel economy of automatic transmission (AT) equipped vehicles. However, a special automatic transmission fluid (ATF) which combines an anti-shudder property with high torque capacity is required for this system. In this study, we established additive technology for ATF having a sufficient anti-shudder property and high torque capacity. Based on the technology, new ATF: ATF-T4 was developed. It was confirmed in actual AT tests that ATF-T4 has excellent anti-shudder durability and high torque capacity. Furthermore, ATF-T4 has good SAE No. 2 friction characteristics, oxidation stability, compatibility with materials (elastomers, nylons, etc.) and viscosity at low temperatures.

A new hybrid transmission has been developed for all-wheel-drive (AWD) cars, and is used in the new Lexus LS600h and LS600hL for its first application. It has a compact layout consisting of a power-split device, generator, high-output electric motor, and a two-stage speed reduction device. Combined with a 5-liter V-8 engine, it achieves power performance rivaling 6-liter engine vehicles, the fuel efficiency of a medium-class vehicle, and outstanding quietness. This paper describes the structure, performance, and shift control technology of this hybrid transmission.

The hybrid system has the typical advantage that it can realize various types of system control, because the system has two power units, engine and motor. On the other hand, however, constraints are increasing due to the complexity of the vehicle system. Compared to the conventional HILS construction and application, there are mainly two typical characteristics or themes for HV-HILS (i.e. HILS for hybrid vehicle control development). Firstly, HV-HILS requires full vehicle simulation environment, because the plural ECU control logic is intricately intertwined. Secondly, recent HILS system needs to run with more accurate or complicated plant models which are necessary to develop more accurate vehicle control logic.