Search Results

The scope of this recommended practice limits itself to the seven different services mentioned in 1.2. It has focused on these aircraft services because:

This Aerospace Recommended Practice includes the following areas: basis for system requirements; selection of materials coupled with hazards and safety; configuration of design; system operation; and evalua tion testing.

This Aerospace Recommended Practice includes the following areas: basis for system requirements; selection of materials coupled with hazards and safety; configuration of design; system operation; and evaluation testing.

The primary purpose of a Propellant Transfer Unit (PTU) is to temperature-condition and weigh a specific amount of propellant, and transfer if to a vehicle propellant tank. A secondary purpose of a PTU may be to drain propellant from the vehicle tank and return it to the transfer unit when required. The transfer unit may also be used for flushing the vehicle fill lines and transfer unit with appropriate flushing fluids, followed with nitrogen for the purpose of drying the lines and weigh tank. The transfer unit may include provisions for helium purging of the propellant transfer tank and lines, ad supplying a blanket of helium pressure to the transfer tank. Each PTU consists of a piping system with appropriate propellant and pneumatic valves, regulators, relief valves, filters and a propellant pump. Various components such as a scrubber, bubbler, propellant cooler (heat exchanger), propellant weigh tank, weigh scale and a chiller may make up the balance of the assembly.

The tow vehicle should be designed for towbarless push-back and/or maintenance towing of regional type aircraft as specified in 1.3. The design will ensure that the unit will safely secure the aircraft nose landing gear within the coupling system for any operational mode. The purpose of this towing procedure is to achieve a safer and faster operation than is possible with conventional towing equipment.

This SAE Aerospace Recommended Practice (ARP) specifies pictographic symbols for ground support equipment. They have been compiled for the benefit of those who deal with such equipment like airlines, airport authorities, manufacturers etc. in order to facilitate fast and accurate identification of controls, indicators, and decals of powered and unpowered equipment. This document shall promote standardization of terms for controls, indicators etc. of ground support equipment and eliminate language problems. It is recommended to put these pictograms on all future equipment and to retrofit all existing equipment as far as possible.

This SAE Aerospace Recommended Practice (ARP) is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances.

This AIR is intended to be concerned with fleet programs rather than programs for individual units. Technical and administrative considerations in developing an approach to a program will be suggested Organization of material possibly wanted in the form of a detailed specification for airline rebuilder communication is reviewed.

This document shall serve as a guide for format, style, and method of presentation for all material included in manufacturers' publications for ground support equipment (GSE). These requirements shall be observed throughout all publications except where modified by detail requirements for specific publications. AS4828 is not applicable to the development or revision of electronic test equipment user manuals and documents. This document is written in general terms by intention, and in most cases conform to recognized practices in the industry. In the event there is a question which is not specifically covered by this document, the user engineering department should be contacted for guidance before proceeding to the final phase of manual development. Each manual prepared by a manufacturer shall contain an introduction which shall include a brief statement explaining the organization, content, and method for using the manual.

This document applies to special purpose equipment which is used in the ground handling, servicing, and maintenance of transport aircraft. Fixed airport facilities and equipment covered under other sections of Part 1910 of Code of Federal Regulations (OSHA) are excluded from the scope of this document.

This document applies to special purpose equipment which is used in the ground handling, servicing, and maintenance of transport aircraft. Fixed airport facilities and equipment covered under other sections of Part 1910 of Code of Federal Regulations (OSHA) are excluded from the scope of this document.

This document applies to special purpose equipment, excluding fixed facilities, which is used in the ground handling, servicing, and maintenance of aircraft. Equipment covered under other sections of the Federal Register Part 1910 is excluded from this document. This document is to establish minimum safety requirements and should not be used for vehicle design criteria. Equipment existing prior to publication date is excluded from the requirements of this document.

This Aerospace Information Report (AIR) is presented in two parts. The first part is simply a summarization of design factors that must be considered in establishing vehicle specifications and design characteristics. The second part refers particularly to the performance characteristics of an aircraft tow tractor. Some definitions, formulas, data, and an example are provided mainly for assisting the specifying engineers of potential buyers and users of aircraft tow tractors in the evaluation and comparison of their requirements with the performance capabilities of the various tow tractors offered by the tow tractor manufacturers. Although the design engineers could also use the formulas and data in their calculations of the performance specifications of aircraft tow tractors, this AIR is not intended to provide the methods and all data necessary for detailed calculations and design of an aircraft tow tractor.

The tow vehicle should be designed for towbarless movement of aircraft on the ground. The design will ensure that the unit will safely secure the aircraft nose landing gear within the coupling system for any operational mode.