Search Results

This paper presents a feedback linearization control technique as applied to a Roll Simulator. The purpose of the Roll Simulator is to reproduce in-field rollovers of ROVs and study occupant kinematics in a laboratory setting. For a system with known parameters, non-linear dynamics and trajectories, the feedback linearization algorithm cancels out the non-linearities such that the closed-loop dynamics behave in a linear fashion. The control inputs are computed values that are needed to attain certain desired motions. The computed values are a form of inverse dynamics or feed-forward calculation. With increasing system eigenvalue, the controller exhibits greater response time. This, however, puts a greater demand on the translational actuator. The controller also demonstrates that it is able to compensate for and reject a disturbance in force level.

The tractor trailer models discussed in this paper were for a real-time hardware-in-the-loop (HIL) simulation to test heavy truck electronic stability control (ESC) systems [1]. The accuracy of the simulation results relies on the fidelity and accuracy of the vehicle parameters used. However in this case where hardware components are part of the simulation, their accuracy also affects the proper working of the simulation and ESC unit. Hence both the software and hardware components have to be validated. The validation process discussed in this paper is divided into two sections. The first section deals with the validation of the TruckSim vehicle model, where experimental data is compared with simulation results from TruckSim. Once the vehicle models are validated, they are incorporated in the HIL simulation and the second section discusses the validation of the whole HIL system with ESC.

Typical factors that contribute to the coast down characteristics of a vehicle include aerodynamic drag, gravitational forces due to slope, pumping losses within the engine, frictional losses throughout the powertrain, and tire rolling resistance. When summed together, these reactions yield predictable deceleration values that can be related to vehicle speeds. This paper focuses on vehicle decelerations while coasting with a typical medium-sized SUV. Drag factors can be classified into two categories: (1) those that are caused by environmental factors (wind and slope) and (2) those that are caused by the vehicle (powertrain losses, rolling resistance, and drag into stationary air). The purpose of this paper is to provide data that will help engineers understand and model vehicle response after loss of engine power.

This research paper builds onto the wealth of technical information that has been published in the past by engineers such as Flick, Radlinski, and Heusser. For this paper, the pushrod force versus chamber pressure data published by Heusser are supplemented with data taken from brake chamber types not reported on by Heusser in 1991. The utility of Heusser's braking force relationships is explored and discussed. Finally, a straightforward and robust method for calculating truck braking performance, based on the brake stroke measurements and published heavy truck braking test results, is introduced and compared to full-scale vehicle test data.

This research was performed using a designed experiment to evaluate the loss of dry surface braking performance and stability that could be associated with the disablement of specific brake positions on a tractor-semitrailer. The experiment was intended to supplement and update previous research by Heusser, Radlinski, Flick, and others. It also sought to establish reasonable limits for engineering estimates on stopping performance degradation attributable to partial or complete brake failure of individual S-cam air brakes on a class 8 truck. Stopping tests were conducted from 30 mph and 60 mph, with the combination loaded to GCW (80,000 lb.), half-payload, and with the flatbed semitrailer unladen. Both tractor and semitrailer were equipped with antilock brakes. Along with stopping distance, brake pressures, longitudinal acceleration, road wheel speed, and steering wheel position and effort were also recorded.

This paper presents a methodology for validating vehicle stability and control computer simulations. Validation is defined as showing that, within some specified operating range of the vehicle, a simulation's predictions of a vehicle's responses agree with the actual measured vehicle's responses to within some specified level of accuracy. The method uses repeated experimental runs at each test condition to generate sufficient data for statistical analyses. The acquisition and reduction of experimental data, and the processing path for simulation data, are described. The usefulness of time domain validation for steady state and slowly varying transients is discussed. The importance of frequency domain validation for thoroughly validating a simulation is shown. Both qualitative and quantitative methods for the comparison of the simulation predictions with the actual test measurements are developed.

This paper describes an experimental program of tire research used to quantify the concept of the “relaxation length” of the fully rolling, steered tire. Two methods of developing lateral force are compared for the general car with the result that a first-order differential equation is obtained from which the change is lateral force with time, or distance, as the steer angle variation is computed.

This paper describes the development of a more accurate shock absorber model in order to obtain better vehicle simulation results. Previous shock models used a single spline to represent shock force versus shock velocity curves. These models produced errors in vehicle simulations because the damper characteristics are better represented by the application of a hysteresis loop in the model. Thus, a new damper model that includes a hysteresis loop is developed using Matlab Simulink. The damper characteristics for the new model were extracted from measurements made on a shock dynamometer. The new model better represents experimental shock data. The new shock model is incorporated into two different lumped-parameter vehicle models: one is a three degree-of-freedom vehicle handling model and the other is a seven degree-of-freedom vehicle ride model. The new damper model is compared with the previous model for different shock mileages (different degrees of wear).

This paper describes the development and implementation of an accurate and repeatable path-following algorithm focused ultimately on vehicle testing. A compact, lightweight, and portable hardware package allows easy installation and negligible impact on the vehicle mass, even for the smallest automobile. Innovative features include the ability to generate a smooth, evenly-spaced path vector regardless the quality of the given path. The algorithm proposed in this work is suitable for testing in a controlled environment. The system was evaluated in simulation and performed well in road tests at low speeds.

This research focuses on the development and performance of analytical models to simulate a tractor-semitrailer in straight-ahead braking. The simulations were modified and tuned to simulate full-treadle braking with all brakes functioning correctly, as well as the behavior of the tractor-semitrailer rig under full braking with selected brakes disabled. The models were constructed in TruckSim and based on a tractor-semitrailer used in dry braking performance testing. The full-scale vehicle braking research was designed to define limits for engineering estimates on stopping distance when Class 8 air-braked vehicles experience partial degradation of the foundation brake system. In the full scale testing, stops were conducted from 30 mph and 60 mph, with the combination loaded to 80,000 lbs (gross combined weight or GCW), half payload, and with the tractor-semitrailer unladen (lightly loaded vehicle weight, or LLVW).

This paper deals with the ongoing efforts at The Vehicle Research and Test Center (VRTC) in East Liberty, Ohio in promoting the safe operation of heavy trucks. The associated research evaluated two vehicle dynamics simulations for their accuracy in predicting tractor-trailer handling metrics. The goals of the research were threefold: 1. Establish a generic “benchmark” parametric data set for the three-axle truck/two-axle trailer vehicle 2. Demonstrate the accuracy of experimental data that was collected for the tractor-trailer vehicle of this study 3. Demonstrate the accuracy of two vehicle simulations by comparing their predicted responses to experimentally observed vehicle responses and metrics.

During Phase VI of the National Highway Traffic Safety Administration's (NHTSA) Light Vehicle Rollover Research Program, three of the twenty-six light vehicles tested exhibited significant response asymmetries with respect to left versus right steer maneuvers. This paper investigates possible vehicle asymmetric characteristics and unintended inputs that may cause vehicle asymmetric response. An analysis of the field test data, results from suspension and steering parameter measurements, and a summary of a computer simulation study are also given.

This study involves two areas of research. The first is the finalization of the Pedestrian Crash Data Study (PCDS) in order to provide detailed information regarding the vehicle/pedestrian accident environment and how it has changed from the interim PCDS information. The pedestrian kinematics, injury contact sources, and injuries were analyzed relative to vehicle geometry. The second area presented is full-scale attempts at reconstruction of two selected PCDS cases using the Polar II pedestrian dummy to determine if the pre-crash motion of the pedestrian and vehicle could somehow be linked to the injuries and vehicle damage documented in the case.

Computer simulations are popular for modeling vehicle system dynamics. However, further refinement of the vehicle dynamic model is required for extensive use in the automotive industry. In this paper, the model refining procedure is illustrated by developing reliable kinematic models verified with laboratory test results; instrument test data; and a mathematical optimization method. More specifically, simple kinematic models are developed for reduced computation times using ADAMS. They are tuned by the gradient-based optimization technique using the results from a laboratory testing facility, which includes the compliance effect in order to use the kinematic models in dynamic simulations. Also the Magic Formula tire model is developed using the optimization method and tire property data for the STI (Systems Technology, Incorporated) tire model.

This paper presents the results of an in-depth study of the measurement of occupant kinematic response on the S-E-A Roll Simulator. This roll simulator was built to provide an accurate and repeatable test procedure for the evaluation of occupant protection and restraint systems during roll events within a variety of occupant compartments. In the present work this roll simulator was utilized for minimum-energy, or threshold type, rollover events of recreational off-highway vehicles (ROVs). Input profiles for these tests were obtained through a separate study involving autonomous full vehicle tests [1]. During simulated roll events anthropomorphic test device (ATD) responses were measured using on-board high speed video, an optical three-dimensional motion capture system (OCMS) and an array of string potentiometers.

For some vehicle dynamics applications, an estimate of a vehicle's center of gravity (cg) height and mass moments of inertia can suffice. For other applications, such as vehicle models and simulations used for vehicle development, these values should be as accurate as possible. This paper presents several topics related to inertial parameter estimation and measurement. The first is a simple but reliable method of estimating vehicle mass moment of inertia values from data such as the center of gravity height, roof height, track width, and other easily measurable values of any light road vehicle. The second is an error analysis showing the effect, during a simple static cg height test, of vehicle motion (relative to the support system) on the vehicle's calculated cg height. A method of accounting for this motion is presented. Similarly, the effects of vehicle motion are analyzed for subsequent mass moment of inertia tests.

This paper presents the development of a tire model for use in the simulation of vehicle dynamics. The model was developed to predict tire lateral and longitudinal force responses to dynamic inputs. In this new tire model, the contact patch of a tire is lumped into a number of elements to study the dynamic behavior of the displacement of the tire contact patch in the lateral and longitudinal directions. For each displacement, a differential equation governing the dynamic behavior of the displacement to the dynamic inputs is derived. Based on the differential equations for the lateral and longitudinal displacements, difference equations are derived for the purpose of simulating tire output responses. Since system parameters, such as mass, damping and stiffness, in the difference equations are unknown, estimation of system parameters is performed using the differential equations and experimental data measured for this research.

This paper describes the design of a vehicle inertia measurement facility (VIMF): a facility used to measure vehicle center of gravity position; vehicle roll, pitch, and yaw mass moments of inertia; and vehicle roll/yaw mass product of inertia. The rationale for general design decisions and the methods used to arrive at the decisions are discussed. The design is inspired by the desire to have minimal measurement error and short test time. The design was guided by analytical error analyses of the contributions of individual system errors to the overall measurement error. A National Highway Traffic Safety Administration (NHTSA) database of center of gravity position and mass moment of inertia data for over 300 vehicles was used in conjunction with the error analyses to design various VIMF components, such as the roll and yaw spring sizes.

This paper discusses the development of a 1994 Ford Taurus vehicle model for the National Advanced Driving Simulator's planned vehicle dynamics simulation, NADSdyna. The front and rear suspensions of the Taurus are modeled using recursive rigid body dynamics formulations. To complement vehicle dynamics, subsystems models that include steering, braking, and tire forces are included. These models provide state-of-the-art high fidelity vehicle handling dynamics for real-time simulation. The realism of a particular formulation depend heavily on how the parameters are obtained from the physical system. Therefore, the development of a data set for a particular model is as important as the model itself. The methodology for generating the Taurus data set is presented. The power train model is not yet included, so the simulation is run with the vehicle either at constant speed or decelerating.

This paper presents an evaluation of a vehicle dynamics model intended to be used for the National Advanced Driving Simulator (NADS). Dynamic validation for high performance simulation is not merely a comparison between experimental and simulation plots. It involves strong insight of vehicle's subsystems mechanics, limitations of the mathematical formulations, and experimental predictions. Lateral, longitudinal, and ride dynamics are evaluated using field test data, and analytical diagnostics. The evaluation includes linear and non-linear range of vehicle dynamics response.