Refine Your Search

Search Results

Standard

Oil Filter Test Procedure

2020-07-08
WIP
J3236
To update and document the oil filter test methods currently captured in SAE HS 806. This will allow for the evaluation of performance characteristics of full-flow oil filters using updated methods.
Standard

Standard Fuel Filter Test Fluid

1994-04-04
HISTORICAL
J1696_199404
This SAE Standard defines the requirements for fluid to be used in the SAE Fuel Filter Test Procedures.
Standard

Standard Fuel Filter Test Fluid

2017-04-18
CURRENT
J1696_201704
This SAE Standard defines the requirements for fluid to be used in the SAE Fuel Filter Test Procedures.
Standard

STANDARD FUEL FILTER TEST FLUID

1997-06-01
HISTORICAL
J1696_199706
This SAE Standard defines the requirements for fluid to be used in the SAE Fuel Filter Test Procedures.
Standard

Coarse Droplet Water/Fuel Separation Test Procedure

2010-10-20
CURRENT
J1839_201010
To determine the undissolved water removal performance of a fuel/water separator under controlled laboratory conditions, using water droplets. This test method is applicable for diesel and biodiesel fuel.
Standard

Fuel Filter - Initial Single-Pass Efficiency Test Method

2006-08-09
HISTORICAL
J1985_200608
This SAE Standard is intended for all sizes of fuel filters, so a variety of test stands may be required depending upon flow rate. The low contamination level, downstream clean-up filter, and short duration of the test ensures that the particle retention ability of the filter is measured in a single pass as no appreciable loading or regression will occur.
Standard

Fuel Filters--Initial Single-Pass Efficiency Test Method

1993-10-01
HISTORICAL
J1985_199310
This SAE Standard is intended for all sizes of fuel filters, so a variety of test stands may be required depending upon flow rate. The low contamination level, downstream clean-up filter, and short duration of the test ensures that the particle retention ability of the filter is measured in a single pass as no appreciable loading or regression will occur.
Standard

Fuel Filter - Initial Single-Pass Efficiency Test Method

2013-10-07
CURRENT
J1985_201310
This SAE Standard is intended for all sizes of fuel filters, so a variety of test stands may be required depending upon flow rate. The low contamination level, downstream clean-up filter, and short duration of the test, ensures that the particle retention ability of the filter is measured in a single pass as no appreciable loading or regression will occur.
Standard

Fuel Filter - Initial Single-Pass Efficiency Test Method

2018-11-28
WIP
J1985
This SAE Standard is intended for all sizes of fuel filters, so a variety of test stands may be required depending upon flow rate. The low contamination level, downstream clean-up filter, and short duration of the test, ensures that the particle retention ability of the filter is measured in a single pass as no appreciable loading or regression will occur.
Standard

Emulsified Water/Fuel Separation Test Procedure

2010-10-22
CURRENT
J1488_201010
To determine the ability of a fuel/water separator to separate emulsified or finely dispersed water from fuels. This test method is applicable for biodiesel fuel.
Standard

Fuel Dispensing Filter Test Methods

2011-02-04
HISTORICAL
J2793_201102
This SAE Recommended Practice is applicable to gasoline and diesel fuel filters installed on fuel dispensing equipment, mobile or stationary. It describes a set of tests used to characterize the structural integrity, filtration performance, and reaction to water contaminant with fuel dispensing filters.
Standard

Fuel Dispensing Filter Test Methods

2020-05-26
CURRENT
J2793_202005
This SAE Recommended Practice is applicable to gasoline and diesel fuel filters installed on fuel dispensing equipment, mobile or stationary. It describes a set of tests used to characterize the structural integrity, filtration performance, and reaction to water contaminant with fuel dispensing filters.
Standard

Filter-Base Mounting

2012-05-29
CURRENT
J363_201205
This SAE Recommended Practice identifies the necessary dimensional characteristics of filter-base mounting configurations to accept the more commonly used lubricating oil and diesel fuel spin-on filters. This SAE document is basically equivalent to the ISO 6415-1981 and ISO 7654-1983 except for differences detailed in the Rationale.
Standard

Filter-Base Mounting

1980-02-01
HISTORICAL
J363_198002
This SAE Recommended Practice identifies the necessary dimensional characteristics of filter-base mounting configurations to accept the more commonly used lubricating oil and diesel fuel spin-on filters. This SAE document is basically equivalent to the ISO 6415-1981 and ISO 7654-1983 except for differences detailed in the Rationale.
Standard

Filter-Base Mounting

1987-02-01
HISTORICAL
J363_198702
This SAE Recommended Practice identifies the necessary dimensional characteristics of filter-base mounting configurations to accept the more commonly used lubricating oil and diesel fuel spin-on filters. This SAE document is basically equivalent to the ISO 6415-1981 and ISO 7654-1983 except for differences detailed in the Rationale.
Standard

Standard Oil Filter Test Oil

1983-06-01
HISTORICAL
J1260_198306
This SAE Standard defines the requirements for an oil to be used in the SAE HS J806N83 Oil Filter Test Procedures.
Standard

Fuel Filter Test Methods

2018-09-20
WIP
J905
The purpose of this fuel filter test method is to provide standardized methods for evaluating the performance characteristics of fuel filters by bench test methods. This, combined with data obtained from application tests, may be used to establish standards of performance for filters when tested by these standard methods. Many variations in requirements of filtration to protect fuel supply equipment on engines and variations in operating conditions make it difficult to specify meaningful "in-service" performance standards by which a filter may be judged. By the use of these standard test methods, test conditions are always the same, and comparisons of the laboratory performance of filters may be made with a high degree of confidence. Once the requirements of a particular application are known, performance standards for suitable filters may be established by these test methods, and adequacy of performance of filters for the job may be determined.
X