Refine Your Search

Topic

Search Results

Technical Paper

Development of a High Sensitivity and High Response Portable Smoke Meter

2014-04-01
2014-01-1580
The filtration efficiency of a DPF drops when it suffers a failure such as melting and cracks during regeneration. And then, on-board diagnostics (OBD) device has become needed worldwide to detect a DPF failure. In the development of an OBD soot sensor, evaluation of the sensor demands a portable instrument which can measure the soot concentration for on-board and in-field use. Some of the emission regulations require the in-field emission measurements under normal in-use operation of a vehicle. This study is intended to develop a high sensitivity and high response portable smoke meter for on-board soot measurements and a reference to OBD soot sensors under development. The smoke meter accommodates a 650 nm laser diode, and its principle is based on light extinction in high soot concentration range and backward light scattering for low soot concentration measurement.
Technical Paper

Simultaneous Measurements of Temperatures of Flame and Wall Surface in a Combustion Chamber of Diesel Engine

2011-08-30
2011-01-2047
In order to investigate the combustion phenomena in a combustion chamber of the diesel engine at transient operations, the simultaneous measurements of temperatures of flame and wall surface in a combustion chamber were conducted. The new technique for simultaneous measurements of flame temperature and wall surface was developed. Laser-Induced phosphorescence was used for the measurement of wall surface temperature which was coupled with the flame temperature measurement by a two-color pyrometry. The NOx and soot emissions were also measured simultaneously in transient operations. The relation between the temporal changes of emissions and temperatures of flame and surface wall are discussed. The results show that the temporal change of NOx emission during transient operation is similar to that of the average gas temperature in a chamber. On the other hand, the temporal change of soot emission is similar to neither that of flame temperature nor that of average gas temperature.
Technical Paper

Investigation of Effects of Ignition Improvers on Ignition Delay Time of Ethanol Combustion with Rapid Compression and Expansion Machine

2012-04-16
2012-01-0854
This work investigates the effects of ignition improvers on the ignition and combustion characteristics of hydrous ethanol with 5% by weight water and 1% by weight Lauric acid (Eh95) under simulated diesel engine conditions using the rapid compression and expansion machine (RCEM). Results indicate that hydrous ethanol with commercial additive (ED95) and hydrous ethanol with 5% by weight glycerol ethoxylate in hydrous ethanol exhibit a near identical rate-of-pressure-rise and heat release rate. Ignition delay of hydrous ethanol with 5% by weight glycerol ethoxylate is shorter, but hydrous ethanol with 1% by weight glycerol ethoxylate has longer ignition delay time and different combustion characteristics compared with hydrous ethanol with commercial additive (ED95). Hydrous ethanol with 1% by weight glycerol ethoxylate and hydrous ethanol with 5% by weight glycerol ethoxylate are considered suitable fuels for high compression-ratio diesel engines.
Technical Paper

Experimental Investigation in Combustion Characteristics of Ethanol-gasoline Blends for Stratified Charge Engine

2011-11-08
2011-32-0551
The increasing of global energy demand and stringent pollution regulations have promoted research on alternative fuels. In Thailand, ethanol, can be produced from many sources of national agriculture products as renewable fuel, which was strongly promoted by government due to its many merits for use in transportation field. In this study, combustion characteristics of ethanol-gasoline blend (20%, 85%, and 100%) as well as pure gasoline (E0) were investigated by using a swirl-generated constant volume combustion chamber. Flame propagations of different fuel blends were observed by high speed Schlieren photography technique while pressure history data were recorded for detailed combustion analysis. Combustion behavior, combustion duration and rate of pressure rise of all tested fuels were investigated in various swirl intensities and equivalence ratios. In addition, effect of swirl intensities and ethanol concentration on lean misfire limit were also discussed.
Technical Paper

Pyrene-LIF Thermometry of the Early Soot Formation Region in a Diesel Spray Flame

2005-09-11
2005-24-006
In order to investigate early soot formation process in diesel combustion, spectral analysis and optical thermometry of early soot formation region in a transient spray flame under diesel-like conditions (Pg2.8 MPa, Tg620-820K) was attempted via laser-induced fluorescence (LIF) from pyrene (C16H10) doped in the fuel. Pyrene is known to exhibit a temperature\-dependent variation of LIF spectrum; the ratio of S2/S1 fluorescence yields, from the lowest excited singlet state S1 and the second excited singlet state S2, depends on temperature. In the present study, pyrene was doped (1%wt) in a model diesel fuel (0-solvent) and the variation of LIF spectra from the pyrene in the spray flame in a rapid compression machine were examined at different ambient temperatures, ambient oxygen concentrations, measurement positions and timings after start of fuel injection.
Technical Paper

A Study on Effect of Heterogeneity of Oxygen Concentration of Mixture in a Combustion Chamber on Combustion and Emissions of Diesel Engine

2007-07-23
2007-01-1845
In this study, the combustion characteristics of diesel flame achieved in a rapid compression and expansion machine (RCEM) at various patterns of oxygen distribution in the chamber are investigated in order to clarify the effect of heterogeneity of oxygen distribution in diesel engines induced by EGR on the soot and NOx emissions. To make the heterogeneous distribution of oxygen in a combustion chamber, the mixtures with different oxygen concentrations are injected through the each different port located on the cylinder wall. Results indicate that the amount of oxygen entrained into the spray upstream the luminous flame region affects the NO emission from diesel flame strongly.
Technical Paper

Comprehensive Characterization of Particulate Emissions from Advanced Diesel Combustion

2007-07-23
2007-01-1945
The applicability of several popular diesel particulate matter (PM) measurement techniques to low temperature combustion is examined. The instruments' performance in measuring low levels of PM from advanced diesel combustion is evaluated. Preliminary emissions optimization of a high-speed light-duty diesel engine was performed for two conventional and two advanced low temperature combustion engine cases. A low PM (<0.2 g/kg_fuel) and NOx (<0.07 g/kg_fuel) advanced low temperature combustion (LTC) condition with high levels of exhaust gas recirculation (EGR) and early injection timing was chosen as a baseline. The three other cases were selected by varying engine load, injection timing, injection pressure, and EGR mass fraction. All engine conditions were run with ultra-low sulfur diesel fuel. An extensive characterization of PM from these engine operating conditions is presented.
Journal Article

Laser-Induced Phosphorescence Thermography of Combustion Chamber Wall of Diesel Engine

2008-04-14
2008-01-1069
In order to investigate the mechanism of heat transfer on the chamber wall of direct-injection diesel engines, 2-D temperature imaging and heat flux measurement in the flame impinging region on the chamber wall were conducted using laser-induced phosphorescence technique. The temperature of the chamber wall surface was measured by the calibrated intensity variation of the 355nm-excited laser-induced phosphorescence from an electrophoretically deposited thin layer of La2O2S:Eu phosphor on a quartz glass plate placed in a rapid compression and expansion machine (RCEM). Instantaneous 2-D images of wall temperature at different timings after start of injection and time-resolved (10kHz) heat flux near the flame impinging region were obtained for combusting and non-combusting diesel sprays with impinging distance of 23.4mm at different injection pressures (80 and 120MPa).
Technical Paper

Ignition, Combustion and Emissions in a DI Diesel Engine Equipped with a Micro-Hole Nozzle

1996-02-01
960321
In an attempt to achieve lean combustion in Diesel engines which has a potential for simultaneous reduction in no and soot, the authors developed a micro-hole nozzle which has orifices with a diameter as small as 0.06 mm. Combustion tests were carried out using a rapid compression-expansion machine which has a DI Diesel type combustion chamber equipped with the micro-hole nozzle. A comparison with the result of a conventional nozzle experiment revealed that the ignition delay was shortened by 30 %, and in spite of that, both peaks of initial premixed combustion and diffusion combustion increased significantly. The combustion in the case of the micro-hole nozzle experiment was accompanied with a decrease in soot emission, whereas an increase in NO emission.
Technical Paper

2-D Imaging of Soot Formation Process in a Transient Spray Flame by Laser-induced Fluorescence and Incandescence Techniques

2002-10-21
2002-01-2669
In order to investigate the soot formation process in a diesel spray flame, simultaneous imaging of soot precursor and soot particles in a transient spray flame achieved in a rapid compression machine was conducted by laser-induced fluorescence (LIF) and by laser-induced incandescence (LII) techniques. The 3rd harmonic (355nm) and the fundamental (1064nm) laser pulses from an Nd:YAG laser, between which a delay of 44ns was imposed by 13.3m of optical path difference, were used to excite LIF from soot precursor and LII from soot particles in the spray flame. The LIF and the LII were separately imaged by two image-intensified CCD cameras with identical detection wavelength of 400nm and bandwidth of 80nm. The LIF from soot precursor was mainly located in the central region of the spray flame between 40 and 55mm (270 to 370 times nozzle orifice diameter d0) from the nozzle orifice. The LII from soot particles was observed to surround the soot precursor LIF region and to extend downstream.
Technical Paper

Measurement of Rate of Multiple-Injection in CDI Diesel Engines

2000-03-06
2000-01-1257
The injection rate meter based on W. Zeuch's method was improved to meet the recent requirement for precise measurement of the multiple injection rate and amount in CDI (Common rail Direct Injection) diesel engines. A pressure sensor with a high sensitivity was added to measure the small pressure increase due to the pilot injection and after injection. At the same time a flow meter having a high accuracy was installed in the discharge pipe line to obtain a correction factor to the modulus of elasticity of volume. As a result it became possible to measure the multiple injection amount at an accuracy of ±0.2mm3/stroke in a range up to 40mm3/stroke.
Technical Paper

Measurement of the Rate of Multiple Fuel Injection with Diesel Fuel and DME

2001-03-05
2001-01-0527
The accuracy of the injection rate meter based on W. Zeuch's method in the measurement of multiple injection rate and amount was calibrated using a small cam driven piston that is driven by an electric motor. For the pre- or early-injection, a sensor with a high sensitivity can be applied to measure the small pressure increase due to the small injection amount. In case of the multiple injection that has the post and/or late injection, a pressure sensor with a low sensitivity must cover not only the large pressure increase due to the main injection but also the small pressure increase due to the post and/or late injection because the output of the high sensitivity sensor is saturated after the main injection. So the linearity of the low sensitivity pressure sensor was calibrated with the cam driven piston prior to the experiment with the actual injection system.
Technical Paper

An Air Cell DI Diesel Engine and Its Soot Emission Characteristics

1983-09-12
831297
A DI diesel engine with an air cell was developed as one of the combustion systems for reducing soot emission from diesel engines: The air is accumulated in the air cell during the compression stroke and is injected into the main chamber during a period after the end of injection. The air jet stirs the stagnant flame and promotes soot oxidation. A comparative experiments with the conventional system made it clear that the air-cell system effectively reduces soot emission at a medium and high load condition.
Technical Paper

Measurement of Droplet Diameter and Fuel Concentration in a Non-Evaporating Diesel Spray by Means of an image Analysis of Shadow Photographs

1984-02-01
840276
A new method was developed which measures the atomization characteristics of a non-evaporating, axisymmetric diesel spray: The film image density of the high speed focused shadow photographs of a spray was analyzed based on the incident light extinction principle, and the Sauter mean diameter and the fuel concentration distribution were calculated from the image data and the measured injection rate with the help of the onion peeling model. The measured Sauter mean diameter showed good agreement with the diameter measured by the conventional immersion method, and also the measured fuel concentration distribution along the spray axis was proved to coincide well with the predicted result by Che one dimentional quasi-steady jet model except at a region near the spray tip.
Technical Paper

A Photographic and Thermodynamic Study of Diesel Combustion in a Rapid Compression Machine

1981-02-01
810259
A diesel spray and flame in a quiescent atmosphere were realized without interference with combustion chamber walls in a newly constructed rapid compression machine. High speed shadow photography and pressure measurement were employed to obtain data for calculating the amount of air entrainment into the the flame and spray. From a comparison of air entrainment between the flame and spray, it turned out that when ignition delay becomes longer air entrainment into flames is promoted by the thermal expansion of multi-points ignition sources in the central region of the spray.
Technical Paper

Two–Dimensional Imaging of Formaldehyde Formed During the Ignition Process of a Diesel Fuel Spray

2000-03-06
2000-01-0236
The time of, and location where ignition first occurs in a diesel fuel spray were investigated in a rapid compression machine (RCM) using the two–dimensional techniques of silicone oil particle scattering imaging (SSI), and the planar laser induced fluorescence (LIF) of formaldehyde. Formaldehyde has been hypothesized to be one of the stable intermediate species marking the start of oxidation reactions in a transient spray under compression ignition conditions. In this study, the LIF images of the formaldehyde formed in a diesel fuel spray during ignition process have been successfully obtained for the first time by exciting formaldehyde with the 3rd harmonic of the Nd:YAG laser. SSI images of the vaporizing spray, and the LIF images of formaldehyde were obtained together with the corresponding time record of combustion chamber pressures at initial ambient temperatures ranging from 580 K to 790 K.
Technical Paper

LDA Measurement and a Theoretical Analysis of the In-Cylinder Air Motion in a DI Diesel Engine

1985-02-01
850106
The swirl velocity in the combustion bowl of a DI diesel engine was measured by means of laser doppler anemometry, varying the swirl intensity and engine speed. At the same time an axisymmetrical two dimensional laminar model for simulating the in-cylinder air motion was presented. The boundary condition of the flow near the wall was investigated by a comparison of predicted and measured swirl velocity, and as a result the free slip condition was found to be suitable for the present model. A comparison between measured and theoretical swirl velocity revealed that the secondary flow in the combustion bowl induced by an interaction between the squish and swirl flow transfers swirl velocities from points to points, causing a complex time variation of the swirl velocity at an observing point.
Technical Paper

Rate of Heat Release and Its Prediction of a Diesel Flame in a Rapid Compression Machine

1984-09-01
841076
The rate of heat release of a free diesel flame was measured with a rapid compression machine which has a compression ratio of 14.7 and a combustion chamber with a diameter of 196 mm and a thickness of 40 mm. Basing on the experimental observations of the high speed photographs of the spray and flame, the authors proposed a phenomenological model for predicting the rate of heat release of the flame. The model consists of three basic models; air entrainment, mixing and combustion model. It was confirmed that the model could successively simulate the rate of heat release of a diesel flame in the quiescent chamber of the rapid compression machine.
Technical Paper

A Study on the Influnce of Intel Angel and Reynolds Number on the Flow-Pattern of Uniflow Scavenging Air

1984-08-01
841056
A cylinder of a model uniflow scavenging engine filled with air at room temperature was scavenged with hot air, and arrival time of the scavenging air was detected with a thermocouple at 20 positions in the cylinder. And shape of front surface of the scavenging air was obtained from these data: The front surface with medium intensity swirl port has a peak in the central part at low running speed, but as the speed increases, it becomes flat causing scavenging efficiency the highest. And finally, a depression appears at its center at very high running speed. Assuming this phenomenon to be analogous to “vortex breakdown” investigated by T.Sarpkaya and others, the authors have proposed a method to determine a geometry of scavenging port that gives the highest scavenging efficiency at a desired Reynolds number, and verified its availability.
Technical Paper

Prediction of the Rate of Heat Release of an Axisymmetrical Diesel Flame in a Rapid Compression Machine

1984-02-01
840519
A phenomenological model for predicting the rate of heat release of an axisymmetrical diesel flame which was achieved in a rapid compression machine has been proposed: Basing on the experimental observations, authors have introduced a new expression about the effects of abrupt thermal expansion due to the initial combustion on the air entrainment. A simple probability density function was also employed to express the distribution of the local equivalence ratio in the flame. The predicted rate of heat release showed good agreement with the experimental results in the diffusion combustion phase.
X