Refine Your Search

Search Results

Viewing 1 to 8 of 8
Technical Paper

Lower Extremity and Brake Pedal Interaction in Frontal Collisions: Sled Tests

1998-02-23
980359
A series of eight sled tests was conducted using Hybrid III dummies and cadavers in order to examine the influence of foot placement on the brake pedal in frontal collisions. The brake pedal in the sled runs was fixed in a fully depressed position and the occupants' muscles were not tensed. The cadaver limbs and the Hybrid III lower extremities with 45° ankle and soft joint-stop were extensively instrumented to determine response during the crash event. Brake pedal reaction forces were measured using a six-axis load cell and high speed film was used for kinematic analysis of the crashes. Four right foot positions were identified from previous simulation studies as those orientations most likely to induce injury. In each test, the left foot was positioned on a simulated footrest, acting as a control variable that produced repeatable results in all dummy tests. Each of the different right foot orientations resulted in different loads and motions of the right leg and foot.
Technical Paper

A New CVS/ATB Hybrid III Model for Lower Extremity Studies: Development and Validation

1998-02-23
980357
A simulation model of the Hybrid III lower extremities with the 30 degree dorsiflexion ankle was developed using the CVS/ATB program. The femur and tibia were modeled as a sequence of rigid beams with a hinge and slider at the knee. Special, locked joints were placed in the femur and tibia at the same locations as the load cells in the actual dummy. Constraint forces and moments at these joints can be compared directly to load cell data. The complex geometry of the foot was divided into five segments representing the heel, toe, forefoot, midfoot, and ankle regions. Two foot models were constructed: one barefoot and one with a Lehigh safety shoe. Good agreement was obtained for most parameters when single-leg pendulum tests, and full-body sled tests, were simulated using the new model.
Technical Paper

Material Properties for Modeling Traumatic Aortic Rupture

2001-11-01
2001-22-0006
Traumatic aortic rupture is a significant cause of fatalities in frontal automobile crashes. However, such ruptures are difficult to reproduce experimentally in cadaveric surrogates, and it is difficult to observe dynamic aortic response in situ. So, the aortic injury mechanism or mechanisms remains in dispute. This study is a staged investigation of the physical parameters and mechanisms of human aortic rupture. The investigation includes both experimental study of local and global viscoelastic properties and failure properties of aortas using aortic tissue samples, excised aortas in vitro, and whole human aortas in situ in cadaver thoraxes. This study is the first phase in a staged programme to develop a finite element computer model of aorta injury to examine the mechanisms of aorta injury in automobile crashes.
Technical Paper

Deployment of Air Bags into the Thorax of an Out-of-Position Dummy

1999-03-01
1999-01-0764
The air bag has proven effective in reducing fatalities in frontal crashes with estimated decreases ranging from 11% to 30% depending on the size of the vehicle [IIHS-1995, Kahane-1996]. At the same time, some air bag designs have caused fatalities when front-seat passengers have been in close proximity to the deploying air bag [Kleinberger-1997]. The objective of this study was to develop an accurate and repeatable out-of-position test fixture to study the deployment of air bags into out-of-position occupants. Tests were performed with a 5th percentile female Hybrid III dummy and studied air bag loading on the thorax using draft ISO-2 out-of-position (OOP) occupant positioning. Two different interpretations of the ISO-2 positioning were used in this study. The first, termed Nominal ISO-2, placed the chin on the steering wheel with the spine parallel to the steering wheel.
Technical Paper

Small Female Head and Neck Interaction With a Deploying Side Air Bag

1999-09-23
1999-13-0013
This paper presents dummy and cadaver experiments designed to investigate the injury potential of an out-of-position small female head and neck from a deploying side air bag. Three seat mounted, thoracic type, side air bags were used that varied in inflator aggressivity. The ATB/CVS multi body program was used to identify the worst case loading position for the small female head and neck. Once the initial position was identified, a total of three Hybrid III 5th percentile dummy and three small female cadaver tests (51 ± 9 years, 64 ± 8 kg, 159 ± 10 cm) were performed. Instrumentation for the dummy included upper and lower neck load cells, while both the dummy and the cadavers had accelerometers and angular rate sensors fixed to the head and T1 vertebrae in order to provide head and neck kinematic data. Head center of gravity accelerations for the dummy ranged from 71 g's to 154 g's, and were greater than cadaver values, which ranged from 68 g's to 103 g's.
Technical Paper

The Influence of Padding and Shoes on the Dynamic Response of Dummy Lower Extremities

1996-02-01
961042
This work studies the effect of padding on the force levels in impulsively loaded dummy lower extremities. Tests include the effect of padding incorporated into the soles of shoes and an examination of the potential of shoe padding for mitigating impact loading on the lower extremities. Three different shoes and three paddings were studied using a pendulum impactor; two different padding levels were studied in an impact sled test with simulated translational structural intrusion. The tests indicate a greater than 20% variation in peak axial force imparted to the lower tibia between shoes, and a greater than 50% variation in peak axial force across the paddings tested. From sled tests with simulated structural intruaion, we see a decrease of approximately 15% in peak axial load and a decrease of over 20% in peak anterior/posterior moment.
Technical Paper

Measurement Techniques for Angular Velocity and Acceleration in an impact Environment

1997-02-24
970575
The University of Virginia is investigating the use of a magnetohydrodynamic (MHD) angular rate sensor to measure head angular acceleration in impact testing. Output from the sensor, which measures angular velocity, must be differentiated to produce angular acceleration. As a precursor to their use in actual testing, a torsional pendulum was developed to analyze an MHD sensor's effectiveness in operating under impact conditions. Differentiated and digitally filtered sensor data provided a good match with the vibratory response of the pendulum for various magnitudes of angular acceleration. Subsequent head drop tests verified that MHD sensors are suitable for measuring head angular acceleration in impact testing.
Technical Paper

Open-Loop Chestbands for Dynamic Deformation Measurements

1998-02-23
980857
Originally designed for measuring closed-loop contours such as those around a human thorax, the External Peripheral Instrument for Deformation Measurement (EPIDM), or chestband, was developed to improve the measurement of dummy and cadaver thoracic response during impact. In the closed-loop configuration, the chestband wraps around on itself forming a closed contour. This study investigates the use of the chestband for dynamic deformation measurements in an open-loop configuration. In the open-loop configuration, the chestband does not generally form a closed contour. This work includes enhanced procedures and algorithms for the calculation of chestband deformation contours including the determination of static and dynamic chestband contours under several boundary conditions.
X