Search Results

This SAE Standard covers propeller shaft couplings for use with propeller shafts up to 3 inches outside diameter.

This SAE Standard covers propeller shaft couplings for use with propeller shafts up to 3 inches outside diameter.

This SAE Recommended Practice establishes minimum requirements for electric hourmeters for general vehicular applications.

This SAE Recommended Practice establishes minimum requirements for electric hourmeters for general vehicular applications.

This SAE Standard covers dimensions, performance parameters, and nomenclature of a push-pull control cable used in outboard, inboard, and sterndrive marine throttle and shift applications.

This SAE Standard covers dimensions, performance parameters and nomenclature of a push-pull control cable used in inboard marine throttle and shift applications.

This SAE Standard covers dimensions, performance parameters and nomenclature of a push-pull control cable used in inboard marine throttle and shift applications.

This SAE Standard covers dimensions and nomenclature of a push-pull control cable used in inboard marine engine applications. The dimensions are representative of existing design practice prevalent in the industry.

This SAE Recommended Practice specifies graphic symbols for operator controls, gauges, tell-tales, indicators, instructions, and warning against risks in small craft and for engines and other equipment intended to be used in small craft.

This SAE Standard establishes the procedure for determining the operator duty cycle sound pressure level Lodc to which operators of powered recreational craft up to 24 m in length are exposed during typical operation as determined by marine engine duty cycle studies. This document describes the instrumentation, the required calibration procedures, the test site, the specifications for “standard craft”, the craft operating conditions, microphone positioning, test procedure, engine speeds for each of the Duty Cycle modes and the formula and table for calculating the Duty Cycle operator ear sound pressure level. This document is subject to change to keep pace with technical advances as well as other international standards and practices. Changes in this Revision: The sound pressure level measurements performed while applying this document are based on the Five-Mode Marine Engine Duty Cycle instead of a single engine speed.

This SAE Standard establishes the procedure for determining the operator duty cycle sound pressure level Lodc to which operators of powered recreational craft up to 24 m in length are exposed during typical operation as determined by marine engine duty cycle studies. This document describes the instrumentation, the required calibration procedures, the test site, the specifications for “standard craft”, the craft operating conditions, microphone positioning, test procedure, engine speeds for each of the Duty Cycle modes and the formula and table for calculating the Duty Cycle operator ear sound pressure level. This document is subject to change to keep pace with technical advances as well as other international standards and practices. Changes in this Revision: The sound pressure level measurements performed while applying this document are based on the Five-Mode Marine Engine Duty Cycle instead of a single engine speed.

Added note

This SAE Recommended Practice covers distributors used on marine engines. NOTE: This includes devices referred to as high voltage switches used for distributing high voltage to the appropriate spark plugs but does not contain any crank position sensing function.

This Standard covers the requirements for all marine inboard and outboard gasoline engine ignition assemblies and components.

This Standard covers the requirements for all marine inboard and outboard gasoline engine ignition assemblies and components.

The purpose of this SAE Recommended Practice is to provide guides toward standard conditions for operating marine hydraulic transmissions where push-pull cable control is applicable. For control cable information see SAE J917. a Provide suitable detents at forward, neutral, and reverse positions. Approximately 22 N (5 lb) of cable force are required to move the engine clutch lever out of the detent positions. b Provide an engine clutch lever with a 6.35 mm (1/4 in) diameter hole at a radius to provide 70 mm (2-3/4 in) linear travel from forward to reverse, with neutral at the center. The engine clutch lever (at 6.35 mm [1/4 in] diameter hole) to have 6.35 mm (1/4 in) maximum thickness. Common cable terminals used are ball joints, clevises, and pivots. c Provide clear cable path to engine clutch lever. d Provide choice of cable paths from different angles. This can be done by providing a sector type of lever with a series of holes equidistant from the centerline of the shaft.

The purpose of this SAE Recommended Practice is to provide guides toward standard conditions for operating marine hydraulic transmissions where push-pull cable control is applicable. For control cable information see SAE J917. a Provide suitable detents at forward, neutral, and reverse positions. Approximately 22 N (5 lb) of cable force are required to move the engine clutch lever out of the detent positions. b Provide an engine clutch lever with a 6.35 mm (1/4 in) diameter hole at a radius to provide 70 mm (2-3/4 in) linear travel from forward to reverse, with neutral at the center. The engine clutch lever (at 6.35 mm [1/4 in] diameter hole) to have 6.35 mm (1/4 in) maximum thickness. Common cable terminals used are ball joints, clevises, and pivots. c Provide clear cable path to engine clutch lever. d Provide choice of cable paths from different angles. This can be done by providing a sector type of lever with a series of holes equidistant from the centerline of the shaft.

The purpose of this SAE Recommended Practice is to provide guides toward standard conditions for operating marine engine throttles (gasoline or diesel) where push-pull cable control is applicable. For control cable information see SAE J917. a Maximum desirable force required to make or maintain a throttle setting, 22 N (5 lb), as applied by the control cable. b Amount of travel required for the engine throttle lever is as follows: 1 Two holes in the engine throttle lever at radii to provide 44.5 mm (1-3/4 in) and 70 mm (2-3/4 in) linear travel, idle to full throttle. 2 The engine throttle lever may be adjustable in length. c The holes in the engine throttle lever for attaching the cable terminal should be 6.35 mm (1/4 in) diameter. The engine throttle lever at these holes should not be more than 6.35 mm (1/4 in) thick.

The purpose of this SAE Recommended Practice is to provide guides toward standard conditions for operating marine engine throttles (gasoline or diesel) where push-pull cable control is applicable. For control cable information see SAE J917. a Maximum desirable force required to make or maintain a throttle setting, 22 N (5 lb), as applied by the control cable. b Amount of travel required for the engine throttle lever is as follows: 1 Two holes in the engine throttle lever at radii to provide 44.5 mm (1-3/4 in) and 70 mm (2-3/4 in) linear travel, idle to full throttle. 2 The engine throttle lever may be adjustable in length. c The holes in the engine throttle lever for attaching the cable terminal should be 6.35 mm (1/4 in) diameter. The engine throttle lever at these holes should not be more than 6.35 mm (1/4 in) thick.