Refine Your Search

Search Results

Standard

Disc Wheel Hub/Spoke Wheel and Axle Interface Dimensions-Commercial Vehicles

1994-09-01
HISTORICAL
J1842_199409
This SAE Recommended Practice is intended for hubs and spoke wheels used on Class 7 and 8 truck/truck-tractor nonpowered front axles, powered and nonpowered rear axles, and trailer axles. The purpose of this document is to establish dimensional guidelines to promote a functional standardization of wheel hubs and spoke wheels in the areas of fasteners, bearing cups, seal bore, and axle drive shaft or hub cap attachment. This document is not intended to exclude the use of wheel hub designs which do not meet the dimensional guidelines for use on defined axle configurations.
Standard

Disc Wheel Hub/Spoke Wheel and Axle Interface Dimensions--Commercial Vehicles

2004-11-22
HISTORICAL
J1842_200411
This SAE Recommended Practice is intended for hubs and spoke wheels used on Class 7 and 8 truck/truck-tractor nonpowered front axles, powered and nonpowered rear axles, and trailer axles. The purpose of this document is to establish dimensional guidelines to promote a functional standardization of wheel hubs and spoke wheels in the areas of fasteners, bearing cups, seal bore, and axle drive shaft or hub cap attachment. This document is not intended to exclude the use of wheel hub designs which do not meet the dimensional guidelines for use on defined axle configurations.
Standard

Disc Wheel Hub/Spoke Wheel and Axle Interface Dimensions - Truck and Bus

2017-05-16
WIP
J1842
This SAE Recommended Practice is intended for hubs and spoke wheels used on Class 6, 7, and 8 truck/truck-tractor non-powered front axles, powered and non-powered rear axles and trailer axles, for which bearing setting is manually adjusted. Assemblies using spacers to control bearing preload and endplay may differ in geometry and bearing componentry.
Standard

Disc Wheel Hub/Spoke Wheel and Axle Interface Dimensions - Truck and Bus

2014-02-03
CURRENT
J1842_201402
This SAE Recommended Practice is intended for hubs and spoke wheels used on Class 6, 7, and 8 truck/truck-tractor non-powered front axles, powered and non-powered rear axles and trailer axles, for which bearing setting is manually adjusted. Assemblies using spacers to control bearing preload and endplay may differ in geometry and bearing componentry.
Standard

Fastener Hardware for Wheels for Demountable Rims

1999-07-29
HISTORICAL
J1835_199907
This SAE Recommended Practice establishes the mounting hardware to be used with demountable rims, wheels for demountable rims, rim spacers designed for 28 degrees bevel mounting systems, and intended for use on commercial vehicles. The dimensions given are those necessary to maintain serviceability and interchangeability of mounting hardware. This document is divided into two sections. Section 1 establishes the practice for new designs for mounting hardware. Section 2 records information on current mounting hardware. Special and less common applications are not covered in this document.
Standard

Fastener Hardware for Wheels for Demountable Rims

1990-03-19
HISTORICAL
J1835_199003
This SAE Recommended Practice establishes the mounting hardware to be used with demountable rims, wheels for demountable rims, rim spacers designed for 28 degrees bevel mounting systems, and intended for use on commercial vehicles. The dimensions given are those necessary to maintain serviceability and interchangeability of mounting hardware. This document is divided into two sections. Section 1 establishes the practice for new designs for mounting hardware. Section 2 records information on current mounting hardware. Special and less common applications are not covered in this document.
Standard

Fastener Hardware for Wheels for Demountable Rims

2004-05-10
HISTORICAL
J1835_200405
This SAE Recommended Practice establishes the mounting hardware to be used with demountable rims, wheels for demountable rims, rim spacers designed for 28 degrees bevel mounting systems, and intended for use on commercial vehicles. The dimensions given are those necessary to maintain serviceability and interchangeability of mounting hardware. This document is divided into two sections. Section 1 establishes the practice for new designs for mounting hardware. Section 2 records information on current mounting hardware. Special and less common applications are not covered in this document.
Standard

Fastener Hardware for Wheels for Demountable Rims

2014-01-03
CURRENT
J1835_201401
This SAE Recommended Practice establishes the mounting hardware to be used with demountable rims, wheels for demountable rims, rim spacers designed for 28 degrees bevel mounting systems, and intended for use on commercial vehicles. The dimensions given are those necessary to maintain serviceability and interchangeability of mounting hardware. This document is divided into two sections. Section 1 establishes the practice for new designs for mounting hardware. Section 2 records information on current mounting hardware. Special and less common applications are not covered in this document.
Standard

Dimensional Compatibility for Commercial Vehicles Fitment of Complete Wheels in Drum Brake Applications - Truck and Bus

2016-07-01
CURRENT
J1865_201607
This SAE Recommended Practice defines a clearance line for establishing dimensional compatibility between drum brakes and wheels with 19.5 inch, 22.5 inch, and 24.5 inch diameter rims. Wheels designed for use with drum brakes may not be suitable for disc brake applications. The lines provided establish the maximum envelope for brakes, including all clearances, and minimum envelope for complete wheels to allow for interchangeability. This document addresses the dimensional characteristics only, and makes no reference to the performance, operational dynamic deflections, or heat dissipation of the system. Valve clearances have not been included in the fitment lines. Bent valves may be required to clear brake drums. Disc brake applications may require additional running clearances beyond those provided by the minimum contour lines. Mounting systems as noted are referenced in SAE J694.
Standard

Dimensional Compatibility for Commercial Vehicles Fitment of Complete Wheels

1999-06-01
HISTORICAL
J1865_199906
This SAE Recommended Practice defines a clearance line for establishing dimensional compatibility between drum brakes and wheels with 19.5 in, 22.5 in, and 24.5 in diameter rims. The clearance line establishes the maximum envelope for brakes and minimum envelope for complete wheels to allow for interchangeability. This document addresses the dimensional characteristics only, and makes no reference to the performance, operational dynamic deflections, or heat dissipation of the system. Valve clearances have not been included in the fitment lines. Bent valves may be required to clear brake drums. Mounting systems as noted are referenced in SAE J694.
Standard

Dimensional Compatibility for Commercial Vehicles Fitment of Complete Wheels in Drum Brake Applications—Truck and Bus

2007-07-31
HISTORICAL
J1865_200707
This SAE Recommended Practice defines a clearance line for establishing dimensional compatibility between drum brakes and wheels with 19.5 in, 22.5 in, and 24.5 in diameter rims. Wheels designed for use with drum brakes may not be suitable for disc brake applications. The clearance line establishes the maximum envelope for brakes and minimum envelope for complete wheels to allow for interchangeability. This document addresses the dimensional characteristics only, and makes no reference to the performance, operational dynamic deflections, or heat dissipation of the system. Valve clearances have not been included in the fitment lines. Bent valves may be required to clear brake drums. Disc brake applications may require additional running clearances beyond those provided by the minimum contour lines. Mounting systems as noted are referenced in SAE J694.
Standard

Fatigue Test Procedures: Hubs and Wheels for Demountable Rims

2016-06-30
CURRENT
J1095_201606
This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing of wheels for demountable rims and hubs intended for normal highway use on trucks, buses, truck trailers, and multipurpose passenger vehicles. The hubs included have bolt circle diameters from 165.1 to 335.0 mm (6.500 to 13.189 in). It is up to each hub and/or wheel for demountable rims manufacturer to determine what test method, accelerated load factor and cycle life requirements are applicable to obtain satisfactory service life in a given application. When deviations from the procedures recommended herein are made, it is the responsibility of the hub and/or wheel for demountable rims developer to modify other parameters to obtain satisfactory service life.
Standard

Fatigue Test Procedures: Hubs and Wheels for Demountable Rims

2009-10-12
HISTORICAL
J1095_200910
This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing of wheels for demountable rims and hubs intended for normal highway use on trucks, buses, truck trailers, and multipurpose passenger vehicles. The hubs included have bolt circle diameters from 165.1 to 335.0 mm (6.50 to 13.19 in). It is up to each hub and/or wheel for demountable rims developer to determine what test method, accelerated load factor and cycle life requirements are applicable to obtain satisfactory service life in a given application. When deviations from the procedures recommended herein are made, it is the responsibility of the hub and/or wheel for demountable rims developer to modify other parameters to obtain satisfactory service life.
Standard

Spoke Wheels and Hub Fatigue Test Procedures

1995-03-01
HISTORICAL
J1095_199503
This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing of spoke wheels and hubs intended for normal highway use on trucks, buses, truck trailers, and multipurpose passenger vehicles. The hubs included have bolt circle diameters from 165.1 to 335.0 mm (6.50 to 13.19 in). It is up to each hum and/or spoke wheel developer to determine what test method, accelerated load factor and cycle life reuirements are applicable to obtain satisfactory service life in a given application. When deviations from the procedures recommended herein are made, it is the responsibility of th ehub and/or spoke wheel developer to modify other parameters to obtain parameters to obtainsatisfactory service life.
Standard

Fatigue Test Procedures: Hubs and Wheels for Demountable Rims

1991-01-01
HISTORICAL
J1095_199101
This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing of spoke wheels and hubs intended for normal highway use on trucks, buses, truck trailers, and multipurpose passenger vehicles. The hubs included have bolt circle diameters from 165.1 to 335.0 mm (6.50 to 13.19 in). It is up to each hub and/or spoke wheel developer to determine what test method, accelerated load factor and cycle life requirements are applicable to obtain satisfactory service life in a given application. When deviations from the procedures recommended herein are made, it is the responsibility of the hub and/or spoke wheel developer to modify other parameters to obtain satisfactory service life.
Standard

Fatigue Test Procedures: Hubs and Wheels for Demountable Rims

1986-03-01
HISTORICAL
J1095_198603
This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing of spoke wheels and hubs intended for normal highway use on trucks, buses, truck trailers, and multipurpose passenger vehicles. The hubs included have bolt circle diameters from 165.1 to 335.0 mm (6.50 to 13.19 in). It is up to each hub and/or spoke wheel developer to determine what test method, accelerated load factor and cycle life requirements are applicable to obtain satisfactory service life in a given application. When deviations from the procedures recommended herein are made, it is the responsibility of the hub and/or spoke wheel developer to modify other parameters to obtain satisfactory service life.
Standard

Spoke Wheels and Hub Fatigue Test Procedures

2003-03-07
HISTORICAL
J1095_200303
This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing of spoke wheels and hubs intended for normal highway use on trucks, buses, truck trailers, and multipurpose passenger vehicles. The hubs included have bolt circle diameters from 165.1 to 335.0 mm (6.50 to 13.19 in). It is up to each hub and/or spoke wheel developer to determine what test method, accelerated load factor and cycle life requirements are applicable to obtain satisfactory service life in a given application. When deviations from the procedures recommended herein are made, it is the responsibility of the hub and/or spoke wheel developer to modify other parameters to obtain satisfactory service life.
Standard

Fatigue Test Procedures: Hubs and Wheels for Demountable Rims

1982-06-01
HISTORICAL
J1095_198206
This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing of spoke wheels and hubs intended for normal highway use on trucks, buses, truck trailers, and multipurpose passenger vehicles. The hubs included have bolt circle diameters from 165.1 to 335.0 mm (6.50 to 13.19 in). It is up to each hub and/or spoke wheel developer to determine what test method, accelerated load factor and cycle life requirements are applicable to obtain satisfactory service life in a given application. When deviations from the procedures recommended herein are made, it is the responsibility of the hub and/or spoke wheel developer to modify other parameters to obtain satisfactory service life.
Standard

Outboard Mounted Brake Drum/Disc Wheel Hub Interface Dimensions - Truck and Bus

2006-05-22
HISTORICAL
J1671_200605
This SAE Recommended Practice contains dimensions and tolerances for outboard mounted brake drums and disc wheel hubs in the interface areas. The geometric features described in this document are shown at true position. This document is intended for outboard mounted brake drums and disc wheel hubs used on Class 7 and 8 commercial vehicles. Special and less common applications are not covered. This document defines and documents the dimensions and tolerances necessary to maintain interchangeability in the interface areas.
X