Refine Your Search

Topic

Affiliation

Search Results

Technical Paper

Application of Shape Memory Heat Engines to Improving Vehicle Fuel Economy

1996-04-01
91A128
Shape memory materials undergo temperature-induced martensitic phase transformations that involve reversible dimensional changes. In performing these changes in shape, the shape-memory material is able to do work against external constraints, and this is the basis for shape-memory low-temperature heat engines. The transformation temperatures on heating and cooling are often not very different (little hysteresis) and are well defined and reproducible. Furthermore, these temperatures can be adjusted by varying the composition of the shape memory alloy. Internal combustion engines dissipate approximately two-thirds of the fuel energy as heat to the exhaust and coolant systems. A low-temperature heat engine could convert a fraction of this heat energy to useful work. This paper discusses the conceptual basis for the application of shape memory heat engines to internal combustion engine powered vehicles. Metallurgical and thermodynamic factors are discussed, as well as engine efficiency.
Technical Paper

Simulors, An Innovative Tool for Molds Development

1996-04-01
91A117
Mold designers and foundrymen spend a lot of time in developing molds without knowing exactly the phenomena which take place inside. Simulor, which has been used in an industrial environment for two years, offers the solution to make foundrymen understand what happens during the filling of the mold and the solidification of the part. Based on navier-stokes and heat transfer equations, simulor provides speed distribution and metal front evolution in the cavity and thermal map in the mold and the part. Some examples with different metals (cast iron, aluminum alloy) cast with various processes (sand or die casting, low pressure or gravity casting) will be given. This new tool will given foundrymen the opportunity to test the mold before having it machined and will also allow reduction in development delays.
Technical Paper

Input Loading for Squeak & Rattle CAE Analysis

1999-05-17
1999-01-1726
A method to create a CAE load by utilizing the vibration motions at structure attachments has been developed. This method employs the concept of enforced motion as the constraints of boundary conditions to create an equivalent input force/moment matrix for a sub-structure with multi-point attachments. The main assumption is that motions at the attachments of the sub-structure should be the same as the known motions of the main structure under the generated input load. The key concept of the developed methodology is the calculation of the input dynamic compliance matrix for sub-structure attachment locations. This method is developed to create a system level input load to be used for squeak and rattle CAE analysis on a component or sub-system. It can also be used for minor component design change evaluation using only the component CAE model, yet as if it is assembled in the vehicle.
Technical Paper

Developing Robust Vibration Excitation and Control Methods for Evaluating Rattle Noise in Automotive Components

1999-05-17
1999-01-1725
The authors participated in a task force that was required to develop a repeatable, dependable, and reliable test procedure to compare, rate, and evaluate the severity of rattles. The assemblies involved in the study are designed and manufactured by different companies and are tested by different people on test equipment and instrumentation from different suppliers. The challenges therefore, were considerable and involved both the vibration inputs and responses as well as the acoustic responses. At the beginning of this activity, it was observed that different test labs using the same Ford vibration specs were obtaining different sounds from the same test item! Clearly, this was unacceptable and the test methods had to be improved and standardized. This paper focuses on vibration related to rattle testing. The particular assemblies used in this study were seat belt retractors.
Technical Paper

The Effects of Retained Fluid and Humidity on the Evacuation of Critical Vehicle Systems

1999-05-10
1999-01-1630
In automotive assembly facilities worldwide, many critical vehicle systems such as brakes, power steering, radiator, and air conditioning require the appropriate fluid to function. In order to insure that these critical vehicle systems receive the correct amount of properly treated fluid, automotive manufacturers employ a method called Evacuation and Fill. Due to their closed-loop design, many critical vehicle systems must be first exposed to vacuum prior to being flooded with fluid. Only after the evacuation and fill process is complete will the critical vehicle system be able to perform as specified. It has long been thought, but never proven, that humidity and entrenched fluid were major hindrances to the Evacuation and Fill process. Consequently, Ford Motor Company Advanced Manufacturing Technology Development, Sandalwood Enterprises, Kettering University, and Dominion Tool & Die conducted a detailed project on this subject.
Technical Paper

Compliance Criteria for Side Facing Aircraft Seats

1999-04-20
1999-01-1598
A series of side facing seat impact sled tests were conducted using the SID, EuroSID-1 and BioSID side impact Anthropomorphic Test Dummies (ATDs) at the FAA Civil Aeromedical Institute (CAMI). The tests were performed on a side facing sofa fixture with a rigid bulkhead adjacent to the forward end of the seat. The purpose of the research project was to examine the methods utilized by the automobile industry to assess thoracic injuries due to side impact accidents, and to investigate the potential applicability of these methods for side facing seats and sofas in civil aircraft. Tests were conducted with single and double occupants. The test conditions complied with the 16g 44 f/s horizontal impact specified in 14 CFR 25.562. Various side impact injury criteria were evaluated in the tests, including the Thoracic Trauma Index (TTI), Viscous Criteria (VC), rib deflection and pelvis acceleration.
Technical Paper

The Design and Testing of Buckling Monocoque Seating Structures for Aircraft

1999-04-20
1999-01-1599
The introduction of FAR23.562 to the Federal Aviation Regulations has necessitated the design and testing of aircraft seats with energy absorbing characteristics to minimize pelvic loads experienced when the seat environment is subject to specified acceleration pulses. Aircraft seat designers have applied various techniques to facilitate this energy absorption. Generally these techniques come at the expense of ease of manufacture and durability. This paper describes the development and testing of seating structures fabricated in a simple and easily reproducible form from sheet aluminium. The design employs both compressive buckling and plastic tensile deformation of the aluminium panels in the seat pan as the means of energy absorption. As the post buckled deflections required to provide sufficient seat stroke are large, the design process does not lend itself to simple theoretical analysis.
Technical Paper

Acoustical Advantages of a New Polypropylene Absorbing Material

1999-05-17
1999-01-1669
Sound absorption is one way to control noise in automotive passenger compartments. Fibrous or porous materials absorb sound in a cavity by dissipating energy associated with a propagating sound wave. The objective of this study was to evaluate the acoustic performance of a cotton fiber absorbing material in comparison to a new polypropylene fibrous material, called ECOSORB ®. The acoustical evaluation was done using measurements of material properties along with sound pressure level from road testing of a fully-assembled vehicle. The new polypropylene fibrous material showed significant advantages over the cotton fiber materials in material properties testing and also in-vehicle measurements. In addition to the performance benefits, the polypropylene absorber provided weight savings over the cotton fiber material.
Technical Paper

A Method to Measure Air Conditioning Refrigerant Contributions to Vehicle Evaporative Emissions (SHED Test)

1999-05-03
1999-01-1539
Although the intent of the SHED test (Sealed Housing for Evaporative Determination) is to measure evaporative fuel losses, the SHED sampling methodology in fact measures hydrocarbons from all vehicle and test equipment sources. Leakage of air conditioning (AC) refrigerant is one possible non-fuel source contributing to the SHED hydrocarbon measurement. This report describes a quick and relatively simple method to identify the contribution of AC refrigerant to the SHED analyzer reading. R134A (CH2FCF3), the hydrofluorocarbon refrigerant used in all current automotive AC systems, as well as its predecessor, the chlorofluorocarbon R12, can be detected using the gas chromatography methods currently in place at many emissions labs for the speciation of exhaust and evaporative hydrocarbon emissions.
Technical Paper

Shoebox Converter Design for Thinwall Ceramic Substrates

1999-05-03
1999-01-1542
Shoebox catalytic converter design to securely mount thinwall substrates with uniform mounting mat Gap Bulk Density (GBD) around the substrate is developed and validated. Computational Fluid Dynamic (CFD) analysis, using heat transfer predictions with and without chemical reaction, allows to carefully select the mounting mat material for the targeted shell skin temperature. CFD analysis enables to design the converter inlet and outlet cones to obtain uniform exhaust gas flow to achieve maximum converter performance and reduce mat erosion. Finite Element Analysis (FEA) is used to design and optimize manufacturing tool geometry and control process. FEA gives insight to simulate the canning process using displacement control to identify and optimize the closing speed and load to achieve uniform mat Gap Bulk Density between the shell and the substrate.
Technical Paper

The Application of Ceramic and Catalytic Coatings to Reduce the Unburned Hydrocarbon Emissions from a Homogeneous Charge Compression Ignition Engine

2000-06-19
2000-01-1833
An experimental and theoretical study of the effect of thermal barriers and catalytic coatings in a Homogeneous Charge Compression Ignition (HCCI) engine has been conducted. The main intent of the study was to investigate if a thermal barrier or catalytic coating of the wall would support the oxidation of the near-wall unburned hydrocarbons. In addition, the effect of these coatings on thermal efficiency due to changed heat transfer characteristics was investigated. The experimental setup was based on a partially coated combustion chamber. The upper part of the cylinder liner, the piston top including the top land, the valves and the cylinder head were all coated. As a thermal barrier, a coating based on plasma-sprayed Al2O3 was used. The catalytic coating was based on plasma-sprayed ZrO2 doped with Platinum. The two coatings tested were of varying thickness' of 0.15, 0.25 and 0.6 mm. The compression ratio was set to 16.75:1.
Technical Paper

Measurement of Instantaneous Heat Flux Flowing Into Metallic and Ceramic Combustion Chamber Walls

2000-06-19
2000-01-1815
Accurate measurements of combustion gas temperature and the coefficient of heat transfer between the gas and the combustion chamber wall of internal combustion engine in cyclic operations are difficult at present. Hence the only method available for determination of states of thermal load and heat loss to the combustion chamber wall in a cycle is to measure the instantaneous temperature on the combustion chamber wall surface accurately and precisely using proper thin-film thermocouples, then to calculate the instantanenous heat flux flowing into the wall surface by means of numerical analysis. However, it is necessary to pay adequate attention to the effects of thermophysical properties of the thermocouple materials on the measured values, since any thermocouple consists of several kinds of materials which are different from those of portions to be measured.
Technical Paper

Graphitic Foam Thermal Management Materials for Electronic Packaging

2000-04-02
2000-01-1576
The goal of this program is to utilize the recently developed high conductivity carbon foam for thermal management in electronics (heat exchangers and heat sinks). The technique used to fabricate the foam produces mesophase pitch-based graphitic foam with extremely high thermal conductivity and an open-celled structure. The thermal properties of the foam have been increased by 79% from 106 to 187 W/m·K at a density of 0.56 g/cm3 through process optimization. It has been demonstrated that when the high-thermal-conductivity graphitic foam is utilized as the core material for the heat exchanger, the effective heat transfer can be increased by at least an order of magnitude compared to traditional designs. A once-through-foam core/aluminum-plated heat exchanger has been fabricated for testing in electronic modules for power inverters.
Technical Paper

Dynamic Analysis of Crew Seats and Cockpit Interiors

2000-05-09
2000-01-1674
Improved safety standards are becoming a focus of the aerospace industry. In particular, standards for occupant protection have been changed to include dynamic seat testing and occupant injury assessment. Methods to model these situations are evolving. A method of modeling an occupant on a crew seat during a sled test is presented. This method combines a rigid body occupant model with a finite element model of the crew seat structure. Validation to sled test results obtained with the model is also presented. Modeling dynamic events with MADYMO software has been proven to be efficient and accurate in many aerospace and automotive applications. Using this tool, a model was developed to investigate how modeling can be used efficiently to provide guidance in crashworthy design. Both finite element methods (FEM) and multibody techniques were used to create a detailed model of a typical aircraft crew seat.
Technical Paper

Design and Test of an Improved Crashworthiness Small Composite Airframe

2000-05-09
2000-01-1673
The goals of this NASA Phase II SBIR program were to develop design methodology to improve occupant survivability in small composite airplanes. Current technology small airplanes absorb crash energy primarily in the cabin structure. The current study tried to increase strength of the occupant compartment and design energy absorbing structure outside the passenger compartment. Dynamics of the crash event were analyzed using a PC version of DYNA3D. Four full scale tests in two crash scenarios were conducted at the NASA Impact Dynamics Test Facility with test parameters set to allow direct comparison with prior NASA/FAA tests. Results indicate that occupant survivability can be improved with moderate weight penalty.
Technical Paper

Investigation of Package Bearings to Improve Driveline Performance

2000-06-19
2000-01-1785
The tapered roller bearings employed in axle centers for the pinion support are critical components in determining the noise, fuel economy and reliability characteristics of the vehicle. They represent a relatively complex mechanical and tribological system, with special requirements from the stiffness, lubrication and heat transfer points of view. This paper brings a contribution to the investigation of the intricate dependency between design parameters, environmental factors and the resultant performance of a package bearing in an integral double cup configuration. Axial compactness, reduced weight, and superior rigidity are only few of the multiple advantages recommending this type of double row bearings for automotive driveline applications. Different aspects related to the tapered roller bearing setting are analyzed in a theoretical and experimental manner, also under the consideration of the manufacturing and assembly processes.
Technical Paper

Experimental and Modeling Evaluations of a Vacuum-Insulated Catalytic Converter

1999-10-25
1999-01-3678
Vehicle evaluations and model calculations were conducted on a vacuum-insulated catalytic converter (VICC). This converter uses vacuum and a eutectic PCM (phase-change material) to prolong the temperature cool-down time and hence, may keep the converter above catalyst light-off between starts. Tailpipe emissions from a 1992 Tier 0 5.2L van were evaluated after 3hr, 12hr, and 24hr soak periods. After a 12hr soak the HC emissions were reduced by about 55% over the baseline HC emissions; after a 24hr soak the device did not exhibit any benefit in light-off compared to a conventional converter. Cool-down characteristics of this VICC indicated that the catalyst mid-bed temperature was about 180°C after 24hrs. Model calculations of the temperature warm-up were conducted on a VICC converter. Different warm-up profiles within the converter were predicted depending on the initial temperature of the device.
Technical Paper

PremAir® Catalyst System – A New Approach to Cleaning the Air

1999-10-25
1999-01-3677
Classical approaches to pollution control have been to develop benign, non-polluting processes or to abate emissions at the tailpipe or stack before release to the atmosphere. A new technology called PremAir® Catalyst Systems1 takes a different approach and reduces ambient, ground level ozone directly. This technology takes advantage of the huge volumes of air which are processed daily by both mobile and stationary heat exchange devices. For mobile applications, the new system involves placing a catalytic coating on a vehicle's radiator or air conditioning condenser. For stationary applications, the catalytic coating typically is applied to an insert, which is attached to the air conditioning condenser. In either case, the catalyst converts ozone to oxygen as ozone containing ambient air passes over the coated radiator or condenser surfaces.
Technical Paper

A Study of Valve Seat Insert Wear Mechanisms

1999-10-25
1999-01-3673
Understanding the wear mechanisms of valve seat inserts (VSIs) is an important aspect in the developments of new alloys for VSI applications. The microhardness of worn VSI is much higher than its original hardness and amount of work-hardening seems to relate to testing conditions and work-hardening coefficient of the material. Worn surfaces of common iron, nickel, and cobalt base alloy VSIs are examined under a scanning electron microscope (SEM). The appearances of worn surfaces show several distinctive characteristics depending on valve seat and VSI materials as well as engine testing conditions. In many intake and dry fuel exhaust applications, worn surfaces exhibit pitting type failure that is associated with crack formation and propagation underneath the surface. In many diesel fuel exhaust applications, oxidation wear mechanism is observed. The wear mechanisms of common VSI materials are also discussed.
Technical Paper

Fouling Prevention Using Plasma Catalysis

1999-10-25
1999-01-3641
Atmospheric pressure nonthermal plasmas packed with a catalyst are applied to decomposition of toxic and hazardous materials in flowing gas streams for building heating, ventilation, and air conditioning (HVAC) systems. We have conducted several experiments wherein the gas phase corona reactor (GPCR) process avoids catalyst-poisoning problems. Cyanogen chloride was passed through a GPCR and a thermal reactor packed with the same three-way automobile catalyst operated at similar conditions including temperature, catalyst volume, and contaminant challenges. Within two hours, the typical breakthrough curve was observed. Large amounts of cyanogen chloride were soon found in the thermal catalyst reactor effluent revealing poisoning. In contrast, the GPCR was operated for over 100 hours without poisoning the catalyst. Other experiments are described.
X