Refine Your Search

Topic

Author

Affiliation

Search Results

Technical Paper

Actuation and Fastening With Shape Memory Alloys in the Automotive Industry

1996-04-01
91A103
As a result of a phase transformation, shape memory alloys can change their shape when the temperature changes. This unusual effect can be utilized in actuation and fastening components for automotive applications. Springs made from Ni-Ti shape memory alloys change their rate in a predetermined temperature range due to a significant change in the elastic modules of the material. They can be used as sensor-actuators in pressures control valves or oil cooler by-pass valves in automatic transmissions or to compensate for oil viscosity changes in shock absorbers or thermal expansion of dissimilar materials in gear boxes. If the recovery is constrained, i.e., shape memory element is physically prevented from returning into its original shape, a potentially high stress is generated. This effect is used in fastener rings. Fasteners made from Ni-Ti alloys provide high reliability and easy installation for braid terminations, locating of shaft mounted components, connectors and hose clamps.
Technical Paper

Ceramic Coating for Aluminum Engine and Components

1996-04-01
91A105
The trend toward lighter vehicles for improved performance has recently introduced the use of aluminum and plastic materials for vehicle bodies and drive trains. In particular, the aluminum alloy block foar engine application is certain to reappear. The soft aluminum cylinder liner will require additional treatment before acceptance. Three possible approaches appear to solve the aluminum cylinder liner dilemma. These approaches are: 1) use of high silicon aluminum such as the 390 aluminum; 2) insert or cast steel liners into the aluminum engine block; and 3) ceramic coat the low cost standard aluminum engine block. Each has known advantages and disadvantages. It is the purpose of this paper to present the merits of option 3, the ceramic coated aluminum cylinder bore, from the standpoint of low weight, cost, and tribological effectiveness. The advantages of approaches 1) and 2) are obvious. High temperature after treatment of the ceramic engine components is not required.
Technical Paper

Trends and Forecasts for Turbocharging

1988-03-01
871147
Predictable and unpredictable forces will change the direction of the charge-air systems industry. The driver of diesel engine development will be the stringent emissions regulations of the 1990s. The drivers in the gasoline engine market will be improved fuel economy, performance, durability and emissions. Forces will also influence the charge-air marketplace, including changes in emission standards, national fiscal policies, political issues, fuel prices, alternate fuels and consumer tastes. The world community mandate for engines that are clean, quiet, durable and fuel efficient will be satisfied, increasingly, by first-tier component suppliers developing integrated systems solutions.
Technical Paper

Engine Control System for Lean Combustion

1988-03-01
871171
In order to achieve lean burn engine control system, it is necessary to develop high accuracy air fuel ratio control technology including transient driving condition and lean burn limit expansion technology. This paper describes the following. 1 The characteristics of the transient response of the fuel supply are clarified when various kinds of air flow measuring methods and fuel injection methods are used. 2 To achieve stable combustion in lean mixture, fine fuel droplet mixture, whose diameter is less than 40 μm, needs to be supplied.
Technical Paper

Calculating Partial Contribution Using Component Sensitivity Values: A Different Approach to Transfer Path Analysis

1999-05-17
1999-01-1693
Transfer Path Analysis (TPA) is a widely used methodology in Noise, Vibration and Harshness (NVH) analysis of motor vehicles. Either it is used to design a vehicle from scratch or it is applied to root cause an existing NVH problem, TPA can be a useful tool. TPA analysis is closely related to the concept of partial contribution. The very basic assumption in TPA is that the summation of all partial contributions from different paths constitutes the total response (which could be either tactile or acoustic). Another popular concept in NVH analysis of vehicles is the component sensitivity. Component sensitivity is a measure of how much the response changes due to a change in one of the components of the system, i.e., the thickness of a panel or elastic rate of an engine mount. Sensitivity rates are more popular among CAE/Simulation community, simply because they are reasonably easy to calculate using mathematical models.
Technical Paper

Door System Design for Improved Closure Sound Quality

1999-05-17
1999-01-1681
Door closing sounds are an important element of the craftsmanship image of a vehicle. This paper examines the relationship between closure sound quality and door system design. The perception of door closing sound quality is shown to be primarily related to it's loudness and sharpness. Of the two, sharpness is more important than loudness. Other factors, like ring-down may also affect closure sound quality. The door system is made up of a number of components. The most important in terms of sound quality are the door and body structure, latch, and door seals. Each of these are classified as either a sound source, a transmission path or a sound radiator. Methods for improving the design of these components for good closure sound quality are discussed in some detail.
Technical Paper

Application of Specialized FEA Dynamic Modeling Techniques for Noise Reduction of Superchargers

1999-05-17
1999-01-1718
A simulation methodology for dynamic modeling of geared rotor systems such as superchargers was used for determining the housing vibration response. The approach provides an ability to make quick parametric design modifications to the model for evaluation of relative noise response with the assumption that the averaged housing vibration level correlates approximately to the noise radiating from the surface. The housing in some cases was modeled as a lumped mass representation for efficiency, and when higher accuracy of housing modes was needed, a detailed flexible Finite Element Analysis (FEA) representation was used. The interesting features of the methodology were the use of constraint equations to model the gear mesh response per unit Transmission Error (TE) input, along with summarizing the component kinetic and strain energy for each mode and the mesh compliance for fast evaluation of opportunities for noise reduction.
Technical Paper

An Investigation of Valve Train Noise for the Sound Quality of I. C. Engines

1999-05-17
1999-01-1711
The dynamic behavior of an OHC valve train system of a spark ignition engine is investigated to characterize the source and transmission of the valve train (VT) vibration and noise and to improve the VT design for better sound quality. The spectral properties of vibration caused by highly transient dynamics of VT system are characterized for the high frequency ranges over 3 kHz, although the overall sound pressure level due to the VT is negligible [1, 2]. For the analysis of valve train a lumped parameter model with 4 d.o.f.'s is developed and validated with the experimental results from a test rig. Experiments are performed on the test rig to measure the valve acceleration, the surface vibration of cylinder head during the operation, and the transfer functions. Also a measurement of cylinder head vibration in a real vehicle has been performed to correlate with the rig test results.
Technical Paper

Noise Analysis of Automotive Alternators

1999-05-17
1999-01-1712
An extensive experimental study of noise generating mechanisms of two production models of automotive alternators is presented. It was established that aerodynamic noise (generated by cooling fans) is dominating at high speeds (above 3,000 rpm), while electromagnetic noise is the most intensive at low rpm. Two directions of noise reduction are proposed and validated: reduction of noise levels generated by alternators to be achieved by using axial flow fans for cooling instead of presently used bladed discs, and radical reduction of operating speed of alternators by using variable transmission ratio accessory drives.
Technical Paper

The Effects of Retained Fluid and Humidity on the Evacuation of Critical Vehicle Systems

1999-05-10
1999-01-1630
In automotive assembly facilities worldwide, many critical vehicle systems such as brakes, power steering, radiator, and air conditioning require the appropriate fluid to function. In order to insure that these critical vehicle systems receive the correct amount of properly treated fluid, automotive manufacturers employ a method called Evacuation and Fill. Due to their closed-loop design, many critical vehicle systems must be first exposed to vacuum prior to being flooded with fluid. Only after the evacuation and fill process is complete will the critical vehicle system be able to perform as specified. It has long been thought, but never proven, that humidity and entrenched fluid were major hindrances to the Evacuation and Fill process. Consequently, Ford Motor Company Advanced Manufacturing Technology Development, Sandalwood Enterprises, Kettering University, and Dominion Tool & Die conducted a detailed project on this subject.
Technical Paper

Design and Acoustic Performance of Baffles Based on Programmed Heat-activated Foams

1999-05-17
1999-01-1673
A programmed heat-activated foam technology has recently been introduced for making baffles to seal hollow car body channels[1,2]. First, we summarize the key characteristics of the programmed foams. Some unique design features such as maximum gap to allow easy E-coat drainage, multiple section design for complex channels, allowance for passage of drainage hose and double-layered baffle are presented. Then, we examine the important design parameters affecting the acoustic performance of baffles based on the programmed foams. The insertion loss(IL) was measured for various baffles expanded in a test channel. The effects of foam expansion ratio, surface density, etc., on the acoustic performance of various single-layered and double-layered baffles are reported.
Technical Paper

Reconstruction of the Cylinder Pressure from Vibration Measurements for Prediction of Exhaust and Noise Emissions in Ethanol Engines

1999-05-17
1999-01-1658
There are growing demands for condition monitoring of IC engines, and therefore any method in order to improve the performance of the engines ought to be evaluated. This paper proposes a new approach for the prediction and optimisation of noise and exhaust emissions in IC engines. The idea is to reconstruct the cylinder pressure from vibration measurements on the engine surface by using the complex cepstrum method [3, 4]. The reconstructed cylinder pressure is further used as input in Multivariate models, based on cylinder pressure, for estimating noise and exhaust emissions. This paper demonstrates the applicability of the method for modelling of noise and exhaust emissions
Technical Paper

Considerations About Chaotic Dynamics of Exhaust Tube and its Design Optimization in Respect to its Dynamic Properties

1999-05-17
1999-01-1657
Vibration of an exhaust tube with a non-linear fixing construction is analyzed. Numerical and laser holography investigation methods are used for the determination of vibration processes happening nearby the cylinder fixing areas. Obviously, the analyzed non-linear system can produce complex reactions even to harmonic excitations. The knowledge about such zones of “wrong” dynamic behavior may help to eliminate and reduce higher noise levels and extend the lifetime of the construction.
Technical Paper

On the Influence of Manifold Geometry on Exhaust Noise

1999-05-17
1999-01-1650
The influence of manifold geometry on exhaust noise is studied. First, a linear description of the problem is presented, so that potential relevant factors may be identified. Then a full non-linear simulation is performed, for a simple geometry, in order to check, in more realistic conditions, the ideas obtained from the linear theory. The results indicate that, although some qualitative trends may be obtained from the linear analysis, the role of back-reaction of the manifold on the engine (a non-linear coupling effect) may be determinant.
Technical Paper

Effect of High Squish Combustion Chamber on Simultaneous Reduction of NOx and Particulate from a Direct-Injection Diesel Engine

1999-05-03
1999-01-1502
In this study it is tried to reduce NOx and particulate emissions simultaneously in a direct injection diesel engine based on the concept of two-stage combustion. At initial combustion stage, NOx emission is reduced with fuel rich combustion. At diffusion combustion stage, particulate emission is reduced with high turbulence combustion. The high squish combustion chamber with reduced throat diameter is used to realize two-stage combustion. This combustion chamber is designed to produce strong squish that causes high turbulence. When throat diameter of the high squish combustion chamber is reduced to some extent, simultaneous reduction of NOx and particulate emissions is achieved with less deterioration of fuel consumption at retarded injection timing. Further reduction of NOx emission is realized by reducing the cavity volume of the high squish combustion chamber. Analysis by endoscopic high speed photography and CFD calculation describes the experimental results.
Technical Paper

A Photographic Investigation of Multi-Stage Fuel Injection in a Single Cylinder DI Diesel Engine

1999-05-03
1999-01-1501
Increasing concern about the impact of internal combustion engines on the environment has led to ever more stringent emission legislation, and the introduction of more sophisticated equipment to enable the requirements to be achieved. One way of improving the emissions from direct injection (DI) diesel engines is to use multi-stage fuel injection, and an investigation performed on such a system is reported in this paper. In this case, the multi-stage fuel injector caused an increase in the exhaust smoke at low load, and an in-cylinder photographic technique was used to examine why this occurred. A multi-stage fuel injector with a VCO nozzle was fitted to a small, high-speed, direct injection diesel engine fitted with a transparent piston for optical access. The combustion process was filmed using a high-speed 16 mm cine camera, and the fuel injection process was illuminated by a high power, copper-vapour laser.
Technical Paper

A Comparison of Gasoline Direct Injection and Port Fuel Injection Vehicles: Part II - Lubricant Oil Performance and Engine Wear

1999-05-03
1999-01-1499
Four 1998 Mitsubishi Carismas, two equipped with direct injection (GDI) and two with port fuel injection engines (PFI) were tested in a designed experiment to determine the effect of mileage accumulation cycle, engine type, fuel and lubricant type on engine wear and engine oil performance parameters. Fuel types were represented by an unadditised base fuel meeting EEC year 2000 specifications and the same base fuel plus synthetic deposit control additive packages. Crankcase oils were represented by two types (1) a 5W-30 API SJ/ILSAC GF-2 type engine oil and (2) a 10W-40 API SH/CF ACEA A3/ B3-96 engine oil. The program showed that specific selection of oil additive chemistry may reduce formation of intake valve deposits in GDI cars.. In general, G-DI engines produced more soot and more pentane insolubles and were found to be more prone to what appears to be soot induced wear than PFI engines.
Technical Paper

What Fuel Economy Improvement Technologies Could Aid the Competitiveness of Light-Duty Natural Gas Vehicles?

1999-05-03
1999-01-1511
The question of whether increasing the fuel economy of light-duty natural gas fueled vehicles can improve their economic competitiveness in the U.S. market, and help the US Department of Energy meet stated goals for such vehicles is explored. Key trade-offs concerning costs, exhaust emissions and other issues are presented for a number of possible advanced engine designs. Projections of fuel economy improvements for a wide range of lean-burn engine technologies have been developed. It appears that compression ignition technologies can give the best potential fuel economy, but are less competitive for light-duty vehicles due to high engine cost. Lean-burn spark ignition technologies are more applicable to light-duty vehicles due to lower overall cost. Meeting Ultra-Low Emission Vehicle standards with efficient lean-burn natural gas engines is a key challenge.
Technical Paper

In-Use Emissions from Natural Gas Fueled Heavy-Duty Vehicles

1999-05-03
1999-01-1507
The objective of the work described here is to test the performance of closed-loop controlled, heavy-duty CNG engines in-use, on fuels of different methane content; and to compare their performance with similar diesel vehicles. Performance is measured in terms of pollutant emissions, fuel economy, and driveability. To achieve this objective, three buses powered by closed-loop controlled, dedicated natural gas engines were tested on the heavy-duty chassis dynamometer facility at the Colorado Institute for Fuels and High Altitude Engine Research (CIFER). Emissions of regulated pollutants (CO, NOx, PM, and THC or NMHC), as well as emissions of alde-hydes for some vehicles, are reported. Two fuels were employed: a high methane fuel (90%) and a low methane fuel (85%). It was found that the NOx, CO, and PM emissions for a given cycle and vehicle are essentially constant for different methane content fuels.
Technical Paper

Effects of a Hybrid Fuel System with Diesel and Premixed DME/Methane Charge on Exhaust Emissions in a Small DI Diesel Engine

1999-05-03
1999-01-1509
Early stage combustion systems, with lean homogeneous charge compression ignition (HCCI), have been studied, with the intent to decrease the pollutant emission characteristics of DI diesel engines. Early stage combustion enables drastic reductions in both nitrogen oxides (NOx) and smoke emission, but the operating load range is restricted, due to combustion phenomena, such as unsteady combustion and knocking. In this study, we explored the possibility of broadening the operating load range in HCCI and reducing pollutant emissions using Dimethyl Ether (DME) fumigated through the intake pipe. However, the improvements in load range were found to be less than 0.1 MPa in brake mean effective pressure (BMEP), even when compression ratios were reduced and Methane with high octane number was mixed. Therefore, a DME premixed charge could be used only at light loads. At heavier loads a hybrid fuel system with a DME premixed charge and diesel fuel injection is necessary.
X