Refine Your Search

Topic

Author

Affiliation

Search Results

Technical Paper

Optimisation of Diesel Engines Converted to High Compression Spark Ignition (SI) Natural Gas Operation

1988-03-01
871149
There is a strong interest around the world in natural gas as an alternative fuel. This paper is concerned with the option of converting diesel engines to spark ignition operation. Although this may appear to be an outrageous thermodynamic action, it is preferable to using natural gas in a low compression gasoline engine conversion. An investigation is described in which engine maps were produced for a 5.6 litre direct injection diesel engine converted to CNG. The diesel operating characteristics have been compared with those of the spark ignition conversion at compression ratios of 18:1 (the original diesel value), 15:1 and 13:1. Detailed data are presented for the 15:1 compression ratio. These test results are supplemented by results for other diesel conversions. The use of these engines in bus fleet operations is also discussed.
Technical Paper

Trends and Forecasts for Turbocharging

1988-03-01
871147
Predictable and unpredictable forces will change the direction of the charge-air systems industry. The driver of diesel engine development will be the stringent emissions regulations of the 1990s. The drivers in the gasoline engine market will be improved fuel economy, performance, durability and emissions. Forces will also influence the charge-air marketplace, including changes in emission standards, national fiscal policies, political issues, fuel prices, alternate fuels and consumer tastes. The world community mandate for engines that are clean, quiet, durable and fuel efficient will be satisfied, increasingly, by first-tier component suppliers developing integrated systems solutions.
Technical Paper

Performance and Exhaust Emission in Spark Ignition Engine Fueled with Methanol-Butane Mixture

1988-03-01
871165
To improve the cold startability of methanol, methanol-butane mixed fuel was experimented. Engine performance and exhaust emissions are obtained with methanol-butane mixed fuel. These characteristics are compared with those of methanol and gasoline. The mixing ratios of methanol and butane are 50:50 (M50), 80:20 (M80), and 90:10 (M90) based on the calorific value. As a result, M90 produces more power than gasoline and more or less than methanol depending on the engine speed and the excess air ratio. Brake horse power of M90 is higher than that of gasoline by 5 - 10 %, and brake specific fuel consumption is smaller than that of gasoline by 17 % to the maximum based on the calorific value. NOx emission concentrations for M90 are lower than those for gasoline and higher than those for methanol because of the effect of butane, CO emission concentrations are somewhat lower than those for methanol and gasoline.
Technical Paper

Application of Specialized FEA Dynamic Modeling Techniques for Noise Reduction of Superchargers

1999-05-17
1999-01-1718
A simulation methodology for dynamic modeling of geared rotor systems such as superchargers was used for determining the housing vibration response. The approach provides an ability to make quick parametric design modifications to the model for evaluation of relative noise response with the assumption that the averaged housing vibration level correlates approximately to the noise radiating from the surface. The housing in some cases was modeled as a lumped mass representation for efficiency, and when higher accuracy of housing modes was needed, a detailed flexible Finite Element Analysis (FEA) representation was used. The interesting features of the methodology were the use of constraint equations to model the gear mesh response per unit Transmission Error (TE) input, along with summarizing the component kinetic and strain energy for each mode and the mesh compliance for fast evaluation of opportunities for noise reduction.
Technical Paper

Reconstruction of the Cylinder Pressure from Vibration Measurements for Prediction of Exhaust and Noise Emissions in Ethanol Engines

1999-05-17
1999-01-1658
There are growing demands for condition monitoring of IC engines, and therefore any method in order to improve the performance of the engines ought to be evaluated. This paper proposes a new approach for the prediction and optimisation of noise and exhaust emissions in IC engines. The idea is to reconstruct the cylinder pressure from vibration measurements on the engine surface by using the complex cepstrum method [3, 4]. The reconstructed cylinder pressure is further used as input in Multivariate models, based on cylinder pressure, for estimating noise and exhaust emissions. This paper demonstrates the applicability of the method for modelling of noise and exhaust emissions
Technical Paper

Considerations About Chaotic Dynamics of Exhaust Tube and its Design Optimization in Respect to its Dynamic Properties

1999-05-17
1999-01-1657
Vibration of an exhaust tube with a non-linear fixing construction is analyzed. Numerical and laser holography investigation methods are used for the determination of vibration processes happening nearby the cylinder fixing areas. Obviously, the analyzed non-linear system can produce complex reactions even to harmonic excitations. The knowledge about such zones of “wrong” dynamic behavior may help to eliminate and reduce higher noise levels and extend the lifetime of the construction.
Technical Paper

On the Influence of Manifold Geometry on Exhaust Noise

1999-05-17
1999-01-1650
The influence of manifold geometry on exhaust noise is studied. First, a linear description of the problem is presented, so that potential relevant factors may be identified. Then a full non-linear simulation is performed, for a simple geometry, in order to check, in more realistic conditions, the ideas obtained from the linear theory. The results indicate that, although some qualitative trends may be obtained from the linear analysis, the role of back-reaction of the manifold on the engine (a non-linear coupling effect) may be determinant.
Technical Paper

Effect of High Squish Combustion Chamber on Simultaneous Reduction of NOx and Particulate from a Direct-Injection Diesel Engine

1999-05-03
1999-01-1502
In this study it is tried to reduce NOx and particulate emissions simultaneously in a direct injection diesel engine based on the concept of two-stage combustion. At initial combustion stage, NOx emission is reduced with fuel rich combustion. At diffusion combustion stage, particulate emission is reduced with high turbulence combustion. The high squish combustion chamber with reduced throat diameter is used to realize two-stage combustion. This combustion chamber is designed to produce strong squish that causes high turbulence. When throat diameter of the high squish combustion chamber is reduced to some extent, simultaneous reduction of NOx and particulate emissions is achieved with less deterioration of fuel consumption at retarded injection timing. Further reduction of NOx emission is realized by reducing the cavity volume of the high squish combustion chamber. Analysis by endoscopic high speed photography and CFD calculation describes the experimental results.
Technical Paper

A Photographic Investigation of Multi-Stage Fuel Injection in a Single Cylinder DI Diesel Engine

1999-05-03
1999-01-1501
Increasing concern about the impact of internal combustion engines on the environment has led to ever more stringent emission legislation, and the introduction of more sophisticated equipment to enable the requirements to be achieved. One way of improving the emissions from direct injection (DI) diesel engines is to use multi-stage fuel injection, and an investigation performed on such a system is reported in this paper. In this case, the multi-stage fuel injector caused an increase in the exhaust smoke at low load, and an in-cylinder photographic technique was used to examine why this occurred. A multi-stage fuel injector with a VCO nozzle was fitted to a small, high-speed, direct injection diesel engine fitted with a transparent piston for optical access. The combustion process was filmed using a high-speed 16 mm cine camera, and the fuel injection process was illuminated by a high power, copper-vapour laser.
Technical Paper

A Comparison of Gasoline Direct Injection and Port Fuel Injection Vehicles: Part II - Lubricant Oil Performance and Engine Wear

1999-05-03
1999-01-1499
Four 1998 Mitsubishi Carismas, two equipped with direct injection (GDI) and two with port fuel injection engines (PFI) were tested in a designed experiment to determine the effect of mileage accumulation cycle, engine type, fuel and lubricant type on engine wear and engine oil performance parameters. Fuel types were represented by an unadditised base fuel meeting EEC year 2000 specifications and the same base fuel plus synthetic deposit control additive packages. Crankcase oils were represented by two types (1) a 5W-30 API SJ/ILSAC GF-2 type engine oil and (2) a 10W-40 API SH/CF ACEA A3/ B3-96 engine oil. The program showed that specific selection of oil additive chemistry may reduce formation of intake valve deposits in GDI cars.. In general, G-DI engines produced more soot and more pentane insolubles and were found to be more prone to what appears to be soot induced wear than PFI engines.
Technical Paper

What Fuel Economy Improvement Technologies Could Aid the Competitiveness of Light-Duty Natural Gas Vehicles?

1999-05-03
1999-01-1511
The question of whether increasing the fuel economy of light-duty natural gas fueled vehicles can improve their economic competitiveness in the U.S. market, and help the US Department of Energy meet stated goals for such vehicles is explored. Key trade-offs concerning costs, exhaust emissions and other issues are presented for a number of possible advanced engine designs. Projections of fuel economy improvements for a wide range of lean-burn engine technologies have been developed. It appears that compression ignition technologies can give the best potential fuel economy, but are less competitive for light-duty vehicles due to high engine cost. Lean-burn spark ignition technologies are more applicable to light-duty vehicles due to lower overall cost. Meeting Ultra-Low Emission Vehicle standards with efficient lean-burn natural gas engines is a key challenge.
Technical Paper

In-Use Emissions from Natural Gas Fueled Heavy-Duty Vehicles

1999-05-03
1999-01-1507
The objective of the work described here is to test the performance of closed-loop controlled, heavy-duty CNG engines in-use, on fuels of different methane content; and to compare their performance with similar diesel vehicles. Performance is measured in terms of pollutant emissions, fuel economy, and driveability. To achieve this objective, three buses powered by closed-loop controlled, dedicated natural gas engines were tested on the heavy-duty chassis dynamometer facility at the Colorado Institute for Fuels and High Altitude Engine Research (CIFER). Emissions of regulated pollutants (CO, NOx, PM, and THC or NMHC), as well as emissions of alde-hydes for some vehicles, are reported. Two fuels were employed: a high methane fuel (90%) and a low methane fuel (85%). It was found that the NOx, CO, and PM emissions for a given cycle and vehicle are essentially constant for different methane content fuels.
Technical Paper

Emissions from Buses with DDC 6V92 Engines Using Synthetic Diesel Fuel

1999-05-03
1999-01-1512
Synthetic diesel fuel can be made from a variety of feedstocks, including coal, natural gas and biomass. Synthetic diesel fuels can have very low sulfur and aromatic content, and excellent autoignition characteristics. Moreover, synthetic diesel fuels may also be economically competitive with California diesel fuel if produced in large volumes. Previous engine laboratory and field tests using a heavy-duty chassis dynamometer indicate that synthetic diesel fuel made using the Fischer-Tropsch (F-T) catalytic conversion process is a promising alternative fuel because it can be used in unmodified diesel engines, and can reduce exhaust emissions substantially. The objective of this study was a preliminary assessment of the emissions from older model transit operated on Mossgas synthetic diesel fuel. The study compared emissions from transit buses operating on Federal no. 2 Diesel fuel, Mossgas synthetic diesel (MGSD), and a 50/50 blend of the two fuels.
Technical Paper

Interim Results from Alternative Fuel Truck Evaluation Project

1999-05-03
1999-01-1505
The objective of this project, which is supported by the U.S. Department of Energy (DOE) through the National Renewable Energy Laboratory (NREL), is to provide a comprehensive comparison of heavy-duty trucks operating on alternative fuels and diesel fuel. Data collection from up to eight sites is planned. Currently, the project has four sites: Raley's in Sacramento, CA (Kenworth, Cummins L10-300G, liquefied natural gas - LNG); Pima Gro Systems, Inc. in Fontana, CA (White/GMC, Caterpillar 3176B Dual-Fuel, compressed natural gas - CNG); Waste Management in Washington, PA (Mack, Mack E7G, LNG); and United Parcel Service in Hartford, CT (Freightliner Custom Chassis, Cummins B5.9G, CNG). This paper summarizes current data collection and evaluation results from this project.
Technical Paper

Effects of a Hybrid Fuel System with Diesel and Premixed DME/Methane Charge on Exhaust Emissions in a Small DI Diesel Engine

1999-05-03
1999-01-1509
Early stage combustion systems, with lean homogeneous charge compression ignition (HCCI), have been studied, with the intent to decrease the pollutant emission characteristics of DI diesel engines. Early stage combustion enables drastic reductions in both nitrogen oxides (NOx) and smoke emission, but the operating load range is restricted, due to combustion phenomena, such as unsteady combustion and knocking. In this study, we explored the possibility of broadening the operating load range in HCCI and reducing pollutant emissions using Dimethyl Ether (DME) fumigated through the intake pipe. However, the improvements in load range were found to be less than 0.1 MPa in brake mean effective pressure (BMEP), even when compression ratios were reduced and Methane with high octane number was mixed. Therefore, a DME premixed charge could be used only at light loads. At heavier loads a hybrid fuel system with a DME premixed charge and diesel fuel injection is necessary.
Technical Paper

Methylal and Methylal-Diesel Blended Fuels for Use in Compression-Ignition Engines

1999-05-03
1999-01-1508
“Gas-to-liquids” catalytic conversion technologies show promise for liberating stranded natural gas reserves and for achieving energy diversity worldwide. Some gas-to-liquids products are used as transportation fuels and as blendstocks for upgrading crude-derived fuels. Methylal (CH3-O-CH2-O-CH3), also known as dimethoxymethane or DMM, is a gas-to-liquid chemical that has been evaluated for use as a diesel fuel component. Methylal contains 42% oxygen by weight and is soluble in diesel fuel. The physical and chemical properties of neat methylal and for blends of methylal in conventional diesel fuel are presented. Methylal was found to be more volatile than diesel fuel, and special precautions for distribution and fuel tank storage are discussed. Steady state engine tests were also performed using an unmodified Cummins B5.9 turbocharged diesel engine to examine the effect of methylal blend concentration on performance and emissions.
Technical Paper

A Model For Estimating Oil Vaporization From The Cylinder Liner As A Contributing Mechanism to Engine Oil Consumption

1999-05-03
1999-01-1520
A model has been developed for estimating the oil vaporization rate from the cylinder liner of a reciprocating engine. The model uses input from an external cycle simulator and an external liner oil film thickness model. It allows for the change in oil composition and the change in oil film thickness due to vaporization. It also estimates how the passage of the compression and scraper rings combine with the vaporization to influence the steady-state composition of the oil layer in the upper ring pack. Computer model results are presented for a compression-ignition engine using a range of liner temperatures, several engine speeds, and two different oils. Vaporization is found to be highly dependent on liner temperature and steady-state oil composition. The steady-state oil composition near the top of the cylinder is found to be significantly different than the composition of the oil near the bottom of the cylinder.
Technical Paper

A Study on Engine Bearing Wear and Fatigue Using EHL Analysis and Experimental Analysis

1999-05-03
1999-01-1514
The possibility of predicting engine bearing durability by elastohydrodynamic lubrication (EHL) calculations was investigated with the aim of being able to improve durability efficiently without conducting numerous confirmation tests. This study focused on the connecting rod big-end bearing of an automotive engine. The mechanisms of wear and fatigue, which determine bearing durability, were estimated by comparing the results of EHL analysis and experimental data. This comparison showed the possibility of predicting the wear amount and the occurrence of fatigue by calculation.
Technical Paper

Effects of Injection Timing and Fuel Properties on Exhaust Odor in DI Diesel Engines

1999-05-03
1999-01-1531
Exhaust odor of DI diesel engines is worse than that of gasoline engines, especially at low temperatures and at idling. As the number of passenger cars with DI diesel engines is increasing worldwide because of their low CO2 emissions, odor reduction research of DI diesel engines is important. Incomplete combustion is a major cause of exhaust odor. Generally, odor worsens due to overleaning of the mixture in the cylinder and due to fuel adhering on the combustion chamber walls. To confirm this, the influences of different engine running conditions and fuel properties were investigated. The reason for the changes in exhaust odor with injection timing is evaluated by considerations of optimum positions of the maximum heat release. With n-heptane, a low boiling point fuel, odorous emissions increase because of overleaning of the mixture.
Technical Paper

Development of Improved Arctic Engine Oil (OEA-30)

1999-05-03
1999-01-1523
U.S. Army arctic engine oil, MIL-L-46167B, designated OEA, provides excellent low-temperature operation and is multi functional. It is suitable for crankcase lubrication of reciprocating internal combustion engines and for power-transmission fluid applications in ground equipment. However, this product required 22-percent derated conditions in the two-cycle diesel engine qualifications test. Overall, OEA oil was limited to a maximum ambient temperature use of 5°C for crankcase applications. The technical feasibility of developing an improved, multi functional arctic engine oil for U.S. military ground mobility equipment was investigated. The concept was proven feasible, and the new oil, designated as OEA-30, has exceptional two-cycle diesel engine performance at full engine output and can be operated beyond the 5°C maximum ambient temperature limit of the MIL-L-46167B product.
X