Search Results

The local equivalence ratio, Φ, was measured in fuel jets using laser-induced spontaneous Raman scattering in an optical heavy duty diesel engine. The measurements were performed at 1200 rpm and quarter load (6 bar IMEP). The objective was to study factors influencing soot formation, such as gas entrainment and lift-off position, and to find correlations with engine-out particulate matter (PM) levels. The effects of nozzle hole size, injection pressure, inlet oxygen concentration, and ambient density at TDC were studied. The position of the lift–off region was determined from OH chemiluminescence images of the flame. The liquid penetration length was measured with Mie scattering to ensure that the Raman measurement was performed in the gaseous part of the spray. The local Φ value was successfully measured inside a fuel jet. A surprisingly low correlation coefficient between engine-out PM and the local Φ in the reaction zone were observed.

Recent measurements in transient diesel jets have shown that fuel in the wake of the injection pulse mixes with ambient gases more rapidly than in a steady jet. This rapid mixing after the end of injection (EOI) can create fuel-lean regions near the fuel injector. These lean regions may not burn to completion for conditions where autoignition occurs after EOI, as is typical of low-temperature combustion (LTC) diesel engines. In this study, transient diesel jets are analyzed using a simple one-dimensional jet model. The model predicts that after EOI, a region of increased entrainment, termed the “entrainment wave,” travels downstream at twice the initial jet propagation rate. The entrainment wave increases mixing by up to a factor of three. This entrainment wave is not specific to LTC jets, but rather it is important for both conventional diesel combustion and LTC conditions.

The International Space Station (ISS) requires advanced life support to continue its mission as a permanently-manned space laboratory and to reduce logistic resupply requirements as the Space Shuttle retires from service. Additionally, as humans reach to explore the moon and Mars, advanced vehicles and extraterrestrial bases will rely on life support systems that feature in-situ resource utilization to minimize launch weight and enhance mission capability. An obvious goal is the development of advanced systems that meet the requirements of both mission scenarios to reduce development costs by deploying common modules. A high pressure oxygen generating assembly (HPOGA) utilizing a high differential pressure (HDP) water electrolysis cell stack can provide a recharge capability for the high pressure oxygen storage tanks on-board the ISS independently of the Space Shuttle as well as offer a pathway for advanced life support equipment for future manned space exploration missions.

The Soft X-Ray Telescope (SXT) is an instrument on the International X-Ray Observatory (IXO). Its flight mirror assembly (FMA) has a single mirror configuration that includes a 3.3 m diameter and 0.93 m tall mirror assembly. It consists of 24 outer modules, 24 middle modules and 12 inner modules. Each module includes more than 200 mirror segments. There are a total of nearly 14, 000 mirror segments. The operating temperature requirement of the SXT FMA is 20°C. The spatial temperature gradient requirement between the FMA modules is ±1°C or smaller. The spatial temperature gradient requirement within a module is ±0.5°C. This paper presents thermal design considerations to meet these stringent thermal requirements.

{ Natural fibre-reinforced composite has the potential to replace current materials used for automotive industrial applications. Oilseed flax fibre could be used as reinforcement for composites because it is readily available, environmentally friendly and possesses good mechanical properties. In this research, oilseed flax fibre reinforced-LLDPE and -HDPE biocomposites were developed through extrusion and injection molding. The flax fibre was chemically treated to improve the bond between the fibre and polymer. Flax fibre was mixed with low linear density polyethylene (LLDPE) and high density polyethylene (HDPE) with fibre content varying from 10 to 30% by mass and processed by extrusion and injection molding to biocomposites. The mechanical properties, surface properties, and thermal properties of biocomposites were measured to analyze the treatment and processing effect and to compare the effect of different flax fibre concentrations on the biocomposites.

The cost of human natural language translation of Service Information, Assembly Instructions, Training Materials, Operator Manuals and other similar documents is a major expense for manufacturers. One translation avoidance method involves replacing most of a document’s text with still and/or animated graphics. While the graphics with minimum text concept has savings potential, clarity of communication must be maintained for widespread application of this technique. The necessary clarity should be achieved if standards are established for the symbols and graphical conventions used. This paper provides an example of a repair procedure documented using the graphics with minimum text paradigm, describes many of the anticipated standards and provides an update on the progress towards achieving a standard development project.

Many engineers have been working to reduce brake noise in many ways for a long time. So far, a progress has been made in preventing and predicting brake noise. Nevertheless, there are some discrepancies of brake noise generation propensity between testing for the prototype and the production. As known in general, the reason for this unpredicted brake noise occurrence in production is partly due to the variation of the resonant frequency, material and the other unpredictable or unmanageable variations of the components in a brake system. In this paper, effects of chemical components and casting process of gray iron brake disc on its resonant frequency variation have been studied. Especially this paper is focused on the variation in material aspects and manufacturing parameters during disc casting in usual production condition. And their effects are investigated by the variation of out-of-plane modal resonant frequency.

The effectiveness of serial link articulated robots in aerospace drilling and fastening is largely limited by positional accuracy. Unguided production robotic systems are practically limited to +/-0.5mm, whereas the majority of aerospace applications call for tolerances in the +/-0.25mm range. The precision with which holes are placed on an aircraft structure is affected by two main criteria; the volumetric accuracy of the positioner, and how the system is affected when an external load is applied. Production use and testing of off-the-shelf robots has highlighted the major contributor to reduced stiffness and accuracy as being error ahead of the joint position feedback such as backlash and belt stretch. These factors affect the omni-directional repeatability, thus limiting accuracy, and also contribute to deflection of the tool point when process forces are applied.

The presented paper introduces the new software complex aimed at simulation of the riveting process as applied to aircraft parts. The software complex implements the novel mathematical model based on minimization of the potential energy. The paper gives the detailed description of the mathematical model and particularizes the main features of the software. The physical and numerical tests aimed at validation of the software are also described in the paper.

Manual drilling and Lockbolt installation in carbon fiber structures is a labor intensive process. To reduce man hour requirements while concurrently improving throughput and process quality levels BROETJE-Automation developed a gantry positioning system with high performance multi-function end effectors for this application. This paper presents a unique solution featuring fully automated drilling and Lockbolt installation (inclusive of automated collar installation) for the vertical tail plane (vertical stabilizer) of large commercial aircraft. A flexible and reconfigurable assembly jig facilitates high access of the end effectors and increases the equipment efficiency. The described system fulfils the demand for affordable yet flexible precision manufacturing with the capacity to handle different aircraft model panels within the work envelope.

If Design of Experiments (DOE) is so good why isn't it used more? Despite its power DOE has some demanding conditions. You don't have to be a statistician to conduct a successful DOE, however. In Aerospace we are very often faced with the design, improvement or correction of a product, process or service. The most serious task is determination of the most relevant variables or factors that affect the final result or performance of the process or product in question. Once these factors have been established, we then need to determine an optimal combination of settings or levels for each factor. There is also the complicating possibility of interaction among the factors also. Design of Experiments (DOE) is an established statistical technique used on its own or in conjunction with a Six Sigma project to determine the strongest individual factors and if there is interaction among the factors.

Once qualified, manufacturing processes for safety critical components in aero engines are “frozen”, that is no changes are permitted to be made without a time consuming and costly re-validation. Moreover, the material selection for components in modern aero engines, due to high mechanical and thermal loads in operation, is limited to a small range of super alloys. These difficult to machine titanium and nickel based alloys are on the one hand a significant expense factor themselves, and cause considerable costs due to high tool wear on the other hand. Thus, it is intended to carry out time and resource saving experiments and - ideally - being able to transfer available results to similar processes. Using smart experimental design deploying relationships of physical measures involved, the effort of testing can be reduced. This paper explains the method's mathematical background, how the selection of the regarded parameters is carried out as well as the reduction of system inputs.

Water recovery is essential for long-duration space exploration transit and outpost missions. Primary stage wastewater recovery systems partially satisfy this need, and generate concentrated wastewater brines that are unusable without further processing. The Enhanced Brine Dewatering System (EBDS) is being developed to allow nearly complete recovery of water from Lunar Outpost wastewater brines. This paper describes the operation of the EBDS and discusses the development and testing of the major functional materials, components, and subsystems, including the wastewater brine ersatz formulations that are used in subsystem testing. The assembly progress of the EBDS full system prototype is also discussed, as well as plans for testing the prototype hardware.

The objective of this study is to evaluate ventilation efficiency regarding to the International Space Station (ISS) cabin ventilation during the ISS assembly mission 1J. The focus is on carbon dioxide spatial/temporal variations within the Node 2 and attached modules. An integrated model for CO2 transport analysis that combines 3D CFD modeling with the lumped parameter approach has been implemented. CO2 scrubbing from the air by means of two ISS removal systems is taken into account. It has been established that the ventilation scheme with an ISS Node 2 bypass duct reduces short-circuiting effects and provides less CO2 gradients when the Space Shuttle Orbiter is docked to the ISS. This configuration results in reduced CO2 level within the ISS cabin.

Compliance with tighter emission regulations has increased the proportion of parasitic weight in commercial vehicles. In turn, the amount of payload must be reduced to comply with transportation weight requirements. A re-design of commercial vehicle components is necessary to decrease the vehicle weight and improve payload capacity. Side rails have traditionally been manufactured from high strength steels, but significant weight reductions can be achieved by substituting steel side rails with 6013 high strength aluminum alloy side rails. Material and stress analyses are presented in this paper in order to understand the effect of manufacturing process on the material's mechanical behavior. Metallographic and tensile test experiments for the 6013-T4 alloy were performed in preparation for residual stress measurements of a punching operation. Punched holes are critical to the function of the side rail and can lead to high stress levels and cracking.

With the growing environmental concerns, biodegradable materials are gaining more importance. Biocomposites which are made from a combination of biological fiber such as flax and hemp together with plastics are finding a good number of applications in day to day life. Flax has good physical and mechanical properties that can be utilized in areas like construction, biomedical & bioproducts and electronics applications. The quality of fiber depends upon various unit operations used in the processing. Drying is one of the most important unit operations which significantly affect the quality of the fiber. The method of drying for removal of moisture from the fiber significantly affects the drying time and quality. In the present study the raw flax fiber was subjected to drying before and after chemical treatment. The physical properties such as; tensile strength, color and structural changes were measured for raw and chemically treated flax fibers.

The research on using natural fibres as the reinforcement in plastic composites has increased dramatically in the last few years. Flax fibres are renewable resources with low specific mass, reduced energy consumption, and relatively low in cost. These advantages make flax fibres recognized as a potential replacement for glass fibres in composites. Among plastic, polyethylene was concluded to be a suitable material used as matrix in natural fibre reinforced biocomposites. However there are few studies on this area so far. In this paper, the processing method of flax fibre-reinforced polyethylene biocomposites is introduced. Flax fibre polyethylene biocomposite consists of flax fibre as the reinforcing component and high density polyethylene as the matrix. Acrylic acid pre-treatment was applied to flax fibre to improve the bonding between fibre and polyethylene.

Dynamic and quasi-static axial cutting of circular AA6061-T6 extrusions with variable instantaneous wall thickness in the axial direction was completed to investigate the capability of controlling the load/displacement responses of the extrusions. Circular specimens considered for this research had an original nominal wall thickness of 3.175 mm, an external diameter of 50.8 mm, and a tube length of 300 mm. Variations of the wall thickness were completed by material removal of the extrusions using a CNC machine. Specially designed cutters having a block height of 20 mm, a blade tip width of 1.0 mm and a blade shoulder width of 3.0 mm were employed to generate the axial cutting deformation mode. Either one or two cutters were selected to initiate a single or dual cutting deformation. A curved deflector with a profile radius of 50.8 mm was used to flare the cut petalled sidewalk and facilitate the cutting system.

In this paper, the microstructure-based finite element modeling method is used in investigating the loading path dependence of formability of transformation induced plasticity (TRIP) steels. For this purpose, the effects of different loading path on the forming limit diagrams (FLD) of TRIP steels are qualitatively examined using the representative volume element (RVE) of a commercial TRIP800 steel. First, the modeling method was introduced, where a combined isotropic/kinematic hardening rule is adopted for the constituent phases in order to correctly describe the cyclic deformation behaviors of TRIP steels during the forming process with combined loading paths which may include the unloading between the two consecutive loadings. Material parameters for the constituent phases remained the same as those in the authors' previous study [ 1 ] except for some adjustments for the martensite phase due to the introduction of the new combined hardening rule.

Predicting AHSS cracking during crash events and forming processes is an enabling technology for AHSS application. Several fracture criteria including MatFEM and Modified Mohr-Coulomb Criterion were developed recently. However, none of them are designed to cover more fracture modes such as bending fracture and tearing fracture with initial damage. A mixed-mode fracture criterion (MMFC) is proposed and developed to capture multiple fracture modes including in-plane shearing fracture, cross-thickness shearing fracture with bending effect and tearing fracture with initial damage. The associated calibration procedure for this criterion is developed. The criterion is implemented in a commercial FEA code and several lab validations are conducted. The results show its promising potential to predict AHSS cracking at large strain conditions.