Refine Your Search

Topic

Search Results

Standard

Ship Systems and Equipment--Selection of Hydraulic Directional Control Valves

2002-03-28
HISTORICAL
J1783_200203
This SAE Recommended Practice provides the designer with guidance for the selection of directional control valves for use in the hydraulic systems of surface ships and submersibles. This guidance includes use of standard valves and interfaces, minimum envelopes that should be reserved to permit interchangeability, environmental considerations, and general technical requirements.
Standard

Self-Propelled Sweepers and Cleaning Equipment

1997-10-01
HISTORICAL
J2130_199710
This SAE Standard applies to all self-propelled machines that are designed to sweep material from highways, parking lots, and floors in non-residential buildings. Primary methods for removing material can be by mechanical means, pneumatic, washing system, or a combinations. To identify self-propelled cleaning equipment, which are grouped into street and industrial sweepers and scrubbers.
Standard

Directional Drilling Planning and Mapping Nomenclature

2007-08-30
HISTORICAL
J2583_200708
This SAE Standard applies to planning and mapping various types of information associated with directional boring/drilling machines. This type of planning and mapping information is typically used with horizontal earthboring machines as defined by SAE J2022. This is a compilation of terms and definitions commonly associated with the planning and mapping of underground pipe and utility installation by using horizontal earthboring machines.
Standard

Guidelines for Liquid Level Indicators

2007-04-30
HISTORICAL
J48_200704
This SAE Recommended Practice pertains to liquid level determination for any compartment of off-road machinery as defined in SAE J1116 and J1057.
Standard

Electrical Propulsion Control - Off-Road Dumpers

2013-02-21
CURRENT
J1299_201302
This SAE Information Report applies to the control circuits and devices associated with the electrical propulsion system used on electric drive dumpers. Dumper is defined in J/ISO 6165. The document does not apply to auxiliary equipment control systems such as: a Battery charging systems b Engine wiring and control c Monitoring and control circuits not directly affecting the operation of the electric propulsion and retarding system d Lighting e Accessory systems (heating, air conditioning, horns, radios, emergency steering, fire protection, and similar functions).
Standard

Off-Road Rim Maintenance Procedures and Service Precautions Diameter Code 20 and Larger

2019-02-21
CURRENT
J1337_201902
This SAE Recommended Practice covers the important fundamental maintenance and service precautions for all off-road single-piece and multi-piece rims. Detailed information on specific procedures concerning mounting, demounting, maintenance, and service of a particular type, style, or design of off-road rim assembly can be obtained by consulting rim or tire manufacturers or distributors. These procedures and service precautions should be considered in preparation of the machine service manual, the operator's manual, and workplace procedures.
Standard

Torque Ratings for Power Take-off Mounting Pads

2003-07-25
HISTORICAL
J2662_200307
This SAE Recommended Practice is intended to serve as a reference for the amount of torque that a Power Take-Off can induce on the transmission mounting pad. This document will apply to six-bolt, eight-bolt, and rear mounted power take-offs.
Standard

Numbering System for Taps

1990-11-01
HISTORICAL
J2123_199011
This SAE Recommended Practice provides a systematic method for the identification of ground thread taps for inch sizes up to 9.999 in with a Maximum Thread-per-Inch of 99.9, and Metric sizes up to 99.9 mm with a Maximum pitch of 9.99 mm. It is intended to assist in the cataloging and supplying of these tools. It is not intended for ACME, Buttress, or similar type thread forms. NOTE 1—Caution must be taken when assigning codes to prevent specifying taps that cannot be physically or economically manufactured. NOTE 2—The Code Number coming from the manufacturer MUST reflect the actual tool construction. NOTE 3— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.
Standard

Numbering System for Single Diameter Drills

1990-11-01
HISTORICAL
J2122_199011
This SAE Recommended Practice provides a systematic method for the identification of single diameter drills. It is intended to assist in the cataloging and supplying of these tools. NOTE 1—Caution must be taken when assigning codes for designators to prevent specifying drills that cannot be physically or economically manufactured. NOTE 2—In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.
Standard

Safety Requirements for Procurement, Maintenance and Use of Hand-held Powered Tools

2014-09-12
CURRENT
AS6228
This SAE Aerospace Standard (AS) covers the requirements and technical guidance for evaluation of life-cycle cost, productivity, and safety/health factors related to power hand tool selection. It applies approaches to selection of quieter and lower vibration hand-held powered tools, with optimal ergonomic features, for the prevention of Hand-Arm Vibration Syndrome (HAVS), hearing loss and repetitive motion injuries. It suggests use of noise and vibration data provided by vendors to be verified and supplemented by information available through the National Institute for Occupational Safety and Health (NIOSH) and European Union databases. Inclusion/exclusion of data in this document is not intended to imply that all of the products described herein are the only production models that meet this standard. Consumers are requested to consult with manufacturers concerning lists of stock production models that meet this standard.
X