Refine Your Search

Date

Date

Materials properties Suppliers Standard Surface Enhancement Committee

Search Results

Viewing 1 to 20 of 31
12Next >Last >>
Sort by relevance
Standard

SAE Manual on Shot Peening
1967-11-01
HISTORICAL
J808A_196711
This report is intended to provide users and producers of metallic shot and grit1 with general information on methods of mechanically testing metal abrasives in the laboratory.
Standard

Definition for Particle Size
2011-06-01
CURRENT
J391_201106
"Effective particle or domain size" is a phrase used in X-ray diffraction literature to describe the size of the coherent regions within a material which are diffracting. Coherency in this sense means diffracting as a unit. Small particle size causes X-ray line broadening and as such can be measured. It has been shown related to substructure as observed in transmission electron microscopy. Particle size is affected by hardening, cold working, and fatigue; conversely, there is increasing evidence that particle size, per se, affects both static and dynamic strength.
Standard

DEFINITIONS FOR MACROSTRAIN AND MICROSTRAIN
1985-08-01
HISTORICAL
J932_198508
In the analysis and measurement of residual stresses of materials, it has been noted that there are frequently differences in interpretation of the terms "macrostrain" and "microstrain." To assist communication among research personnel in this area, definitions for these two terms are suggested by the Fatigue Design and Evaluation Committee of SAE. Since "macrostress" is commonly computed from "macrostrain" in residual stress analysis, to be consistent, the definitions given are for "macrostrain" and "microstrain."
Standard

Definitions for Macrostrain and Microstrain
2011-08-04
CURRENT
J932_201108
In the analysis and measurement of residual stresses of materials, it has been noted that there are frequently differences in interpretation of the terms "macrostrain" and "microstrain." To assist communication among research personnel in this area, definitions for these two terms are suggested by the Fatigue Design and Evaluation Committee of SAE. Since "macrostress" is commonly computed from "macrostrain" in residual stress analysis, to be consistent, the definitions given are for "macrostrain" and "microstrain."
Standard

CAST STEEL SHOT
1990-03-01
HISTORICAL
J827_199003
This SAE Recommended Practice describes chemical analysis, hardness, microstructure and physical characteristic requirements for cast steel shot to be used for shot peening or blast cleaning operations.
Standard

CUT WIRE SHOT
1993-06-01
HISTORICAL
J441_199306
This SAE Recommended Practice is considered to be tentative and is subject to modification to meet new developments or requirements. It is offered as a guide in the selection and use of cut wire shot.
Standard

Metallic Shot and Grit Mechanical Testing
2022-05-04
CURRENT
J445_202205
This SAE Information Report is intended to provide users and producers of metallic shot and grit2 with general information on methods of mechanically testing metal shot in the laboratory.
Standard

Metallic Shot and Grit Mechanical Testing
2005-07-25
HISTORICAL
J445_200507
This SAE Information Report is intended to provide users and producers of metallic shot and grit2 with general information on methods of mechanically testing metal shot in the laboratory.
Standard

METALLIC SHOT AND GRIT MECHANICAL TESTING
1996-04-01
HISTORICAL
J445_199604
This SAE Information Report is intended to provide users and producers of metallic shot and grit2 with general information on methods of mechanically testing metal shot in the laboratory.
Standard

Metallic Shot and Grit Mechanical Testing
2013-08-21
HISTORICAL
J445_201308
This SAE Information Report is intended to provide users and producers of metallic shot and grit2 with general information on methods of mechanically testing metal shot in the laboratory.
Standard

METALLIC SHOT AND GRIT MECHANICAL TESTING
1984-08-01
HISTORICAL
J445_198408
This report is intended to provide users and producers of metallic shot and grit1 with general information on methods of mechanically testing metal shot in the laboratory.
Standard

CAST SHOT AND GRIT SIZE SPECIFICATIONS FOR PEENING AND CLEANING
1993-05-01
HISTORICAL
J444_199305
This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches1, preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E 11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.
Standard

Cast Shot and Grit Size Specifications for Peening and Cleaning
2010-06-16
HISTORICAL
J444_201006
This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches1, preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E 11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.
Standard

Cast Shot and Grit Size Specifications for Peening and Cleaning
2005-07-25
HISTORICAL
J444_200507
This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches1, preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E 11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.
12Next >Last >>
X