Search Results

Audio CAE is an emerging area of interest for vehicle OEMs. Questions regarding early stages of the vehicle design, like choosing the possible positions for speakers, deciding the installation details that can influence the visual design, and integration of the low frequency speakers with the body & closures structure, are of interest. Therefore, at VCC, the development of the CAE methodology for audio applications has been undertaken. The key to all CAE applications is the loudspeaker model made available in the vibro-acoustic software used within the company. Such a model has been developed, implemented and verified in different frequency ranges and different applications. The applications can be divided into the low frequency ones (concerning the installation of woofers and subwoofers), and the middle/high frequency ones (concerning the installation of midrange and tweeter speakers). In the case of the woofer, it is the interaction with the body vibration that is of interest.

The low frequency acoustic response of the passenger compartment (cavity) in sedans is considered with respect to the coupling between the cavity and the trunk. Both acoustic (via holes in the parcel shelf or behind the backrest of the rear seat), and structural (via the parcel shelf itself, or the panel of the backrest) mechanisms are investigated by both test and CAE. It is found that the peaks in acoustic response of the cavity at low frequencies are due to both acoustic and structural phenomena. However, the acoustic ones can be effectively blocked by proper design of the trim. Recommendations concerning modeling of acoustic effects in sedans are formulated.

This paper describes the development of a robust and accurate method to model one-phase heat exchangers in complete vehicle air flow simulations along with a comprehensive comparison of EFD and CFD results. The comparison shows that the inlet radiator coolant temperatures obtained with CFD were within ±4°C of the experimental data with a trend in the differences being dependent on the car speed. The relative differences in cooling air mass flow rates increase with increasing car speed, with CFD values generally higher than EFD. From the investigation, the conclusion is that the methodology and modeling technique presented offer an accurate tool for concept and system solutions on the front end design, cooling package and fan. Care must be taken in order to provide the best possible boundary conditions paying particular attention to the heat losses in the engine, performance data for the radiator and fan characteristics.

Car body structures and the joints between beam members have a great impact on global vehicle stiffness. With the method presented in this paper it is possible to experimentally assess the stiffness of joints by a robust and economic means. The stiffness of a beam can easily be found experimentally just by cutting it in two and using the cross-sections to calculate the polar moment of inertia. When it comes to a joint, there are no formulae or explicit expressions describing its behavior. Therefore, measurement of its mechanical behavior has to be made. The dynamic joint method presented here does not need levers or a costly, rigid set-up, but an economical free-free set-up and cast-on weights. Furthermore, the same method can be emulated by FEM when a digital model exists.

In the continuous struggle to improve car body properties, and at the same time reduce the weight of the structure, new materials and body concepts are being evaluated. In competition with more self-evident lightweight materials such as aluminium and plastic composites, new and different grades of high-strength steels with various surface coatings are being introduced. From experience it is known that to be able to weld and join these steel grades under high-volume conditions, it is necessary to perform comprehensive testing to establish those assembly parameters which give a superior and reliable weld quality. To meet the demands of cost-effective low volume production, we can notice a tendency to move away from traditional uni-body concepts and into the direction of space-frame structures. These can preferably be manufactured out of high-strength steels by using production methods like roll-forming, hydro-forming and hot-forming.

Flow visualization techniques are widely used in aerodynamics to investigate the surface trace pattern. In this experimental investigation, the surface flow pattern over the rear end of a full-scale passenger car is studied using tufts. The movement of the tufts is recorded with a DSLR still camera, which continuously takes pictures. A novel and efficient tuft image processing algorithm has been developed to extract the tuft orientations in each image. This allows the extraction of the mean tuft angle and other such statistics. From the extracted tuft angles, streamline plots are created to identify points of interest, such as saddle points as well as separation and reattachment lines. Furthermore, the information about the tuft orientation in each time step allows studying steady and unsteady flow phenomena. Hence, the tuft image processing algorithm provides more detailed information about the surface flow than the traditional tuft method.

It has been shown that Inflatable Curtains have the potential to reduce head injuries in side impacts and the system has accordingly been introduced on a growing number of car models. There is also a potential benefit in rollover situations. This paper only consider performance in situations with belted occupants. To date, it has not been possible to implement an Inflatable Curtain in convertible vehicles because they lack a roof. The challenge of the Door Mounted Inflatable Curtain (DMIC) has been to overcome the lack of support and fixation possibilities offered by a roof. This paper includes a description of the DMIC and how it was integrated into the vehicle structure. The paper will also show how to create the space and support needed to utilize the internal stiffness and make it possible to fill the bag in time. The impact attenuation and ejection protection functions of the DMIC will be demonstrated.

The objective of this paper is to investigate whether different appearance modes of the digital human models (DHM or manikins) affect the observers when judging a working posture. A case where the manikin is manually assembling a battery in the boot with help of a lifting device is used in the experiment. 16 different pictures were created and presented for the subjects. All pictures have the same background, but include a unique posture and manikin appearance combination. Four postures and four manikin appearances were used. The subjects were asked to rank the pictures after ergonomic assessment based on posture of the manikin. Subjects taking part in the study were either manufacturing engineering managers, simulation engineers or ergonomists. Results show that the different appearance modes affect the ergonomic judgment. A more realistic looking manikin is rated higher than the very same posture visualized with a less natural appearance.

This paper gives details of the drag and dirt deposition mechanisms related to rear view mirrors. The major design parameters affecting mirror-generated drag and dirt deposition are described. A detailed analysis of the mirror noise properties is not covered for reasons of brevity. A range of test methods is also described which can be successfully used in the mirror optimisation process. The detailed drag breakdown of several rear view mirrors has been made by use of a combination of balance and pressure measurements. The drag breakdown gives an insight into the drag mechanisms and identifies the critical geometry parameters. It is concluded that the relatively high level of drag experienced by some of today's mirrors is primarily the result of premature tip separation and/or an unnecessarily large mirror foot. A level of drag close to the minimum possible, for a given mirror glass area, can be achieved by optimisation of the tip and foot areas.

Frontal Severe Partial Overlap Collisions (SPOC) also called small overlap crashes pose special challenges with respect to structural design as well as occupant protection. In the early 1990s, the SPOC test method was developed addressing 20-40% overlap against a fixed rigid barrier with initial velocities up to 65 km/h. The knowledge gained has been used in the design of Volvo vehicles since then. Important design principles include front side members orientated along the wheel envelopes together with a strong support structure utilizing a space frame principle with beams loaded mainly in tension and compression. This novel setup was first introduced in the 850-model in 1991 and has been refined and patented (2001) in later Volvo front structures. Among the design principles are multiple front side members on each side, helping energy absorption efficiency and robustness.

Most OEMs are shifting their strategy and way of thinking regarding ECUs. This, in combination with the electrification of vehicles and the shift towards software-based companies (car as a device), implies one of the biggest paradigm changes in automotive history. On the other hand, despite the current struggles, remarkable advances have been made in electronic technology during the past few years. These developments have opened a door to very promising enabling technology, with exterior lighting as a main target market. These circumstances seem to have created a perfect storm leading to new strategies for electronic control and driving for (front and rear) exterior lighting. We, at our company, have investigated the enabling technology, challenges, and benefits of this emerging exterior lighting approach, that we call ‘ECU-Less’.

The transition towards battery electric vehicles (BEVs) has increased the focus of vehicle manufacturers on energy efficiency. Ensuring adequate airflow through the heat exchanger is necessary to climatize the vehicle, at the cost of an increase in the aerodynamic drag. With lower cooling airflow requirements in BEVs during driving, the front air intakes could be made smaller and thus be placed with greater freedom. This paper explores the effects on exterior aerodynamics caused by securing a constant cooling airflow through intakes at various positions across the front of the vehicle. High-fidelity simulations were performed on a variation of the open-source AeroSUV model that is more representative of a BEV configuration. To focus on the exterior aerodynamic changes, and under the assumption that the cooling requirements would remain the same for a given driving condition, a constant mass flow boundary condition was defined at the cooling airflow inlets and outlets.