Refine Your Search

Search Results

Standard

Connector for Fluid Power and General Use - Ports and Stud End with ASME B1.1 Threads and O-Ring Seal - Part 4: External Hex and Internal Hex Inch Port Plugs - Dimensions, Design, Test Methods and Requirements

2013-02-08
WIP
J1926/4
This part defines performance requirements, dimensions, and designs for -2 through -32 internal and external hex port plugs for use in SAE J1926-1 ports. Testing and usage through many years confirm the performance requirements of port plugs made from carbon steel. The port plugs were specified in SAE J514 without any performance requirements. They have been developed and tested to gain a 4:1 working pressure rating for industrial applications. In fluid power systems, power is transmitted and controlled through a fluid (liquid or gas) under pressure within an enclosed circuit. In general applications, a fluid may be conveyed under pressure. Components are connected through their threaded ports by stud ends on fluid conductor fittings to tubes and pipes or to hose fittings and hoses. For threaded ports and stud ends specified in new designs in hydraulic fluid power applications, only ISO 6149 shall be used.
Standard

Connector for Fluid Power and General Use - Ports and Stud End with ASME B1.1 Threads and O-Ring Seal - Part 4: External Hex and Internal Hex Inch Port Plugs - Dimensions, Design, Test Methods and Requirements

2009-07-29
HISTORICAL
J1926/4_200907
This part defines performance requirements, dimensions, and designs for -2 through -32 internal and external hex port plugs for use in SAE J1926-1 ports. Testing and usage through many years confirm the performance requirements of port plugs made from carbon steel. The port plugs were specified in SAE J514 without any performance requirements. They have been developed and tested to gain a 4:1 working pressure rating for industrial applications. In fluid power systems, power is transmitted and controlled through a fluid (liquid or gas) under pressure within an enclosed circuit. In general applications, a fluid may be conveyed under pressure. Components are connected through their threaded ports by stud ends on fluid conductor fittings to tubes and pipes or to hose fittings and hoses. For threaded ports and stud ends specified in new designs in hydraulic fluid power applications, only ISO 6149 shall be used.
Standard

Connector for Fluid Power and General Use—Ports and Stud End with ASME B1.1 Threads and O-Ring Seal—Part 4: External Hex and Internal Hex Inch Port Plugs—Dimensions, Design, Test Methods and Requirements

2010-08-05
CURRENT
J1926/4_201008
This part defines performance requirements, dimensions, and designs for −2 through −32 internal and external hex port plugs for use in SAE J1926-1 ports. Testing and usage through many years confirm the performance requirements of port plugs made from carbon steel. The port plugs were specified in SAE J514 without any performance requirements. They have been developed and tested to gain a 4:1 working pressure rating for industrial applications. In fluid power systems, power is transmitted and controlled through a fluid (liquid or gas) under pressure within an enclosed circuit. In general applications, a fluid may be conveyed under pressure. Components are connected through their threaded ports by stud ends on fluid conductor fittings to tubes and pipes or to hose fittings and hoses. For threaded ports and stud ends specified in new designs in hydraulic fluid power applications, only ISO 6149 shall be used.
Standard

Connections for General Use and Fluid Power - Ports and Stud Ends with ASME B1.1 Threads and O-Ring Sealing - Part 2: Heavy-Duty (S Series) Stud Ends

2006-10-04
HISTORICAL
J1926/2_200610
This part of SAE J1926 specifies dimensions, performance requirements, and test procedures for adjustable and nonadjustable heavy-duty (S series) stud ends with ISO 725 threads for use in fluid power and general applications and the O-rings used with them. Stud ends in accordance with this part of SAE J1926 may be used at working pressures up to 63 MPa for nonadjustable stud ends and up to 40 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc. For threaded ports and stud ends specified in new designs for hydraulic fluid power applications, only SAE J2244 (ISO 6149) shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and ISO 11926 shall not be used for new design in hydraulic fluid power applications. Conformance to the dimensional information does not guarantee rated performance.
Standard

Connections for General Use and Fluid Power - Ports and Stud Ends with ASME B1.1 Threads and O-Ring Sealing - Part 2: Heavy-Duty (S Series) Stud Ends

2016-09-09
CURRENT
J1926/2_201609
This part of SAE J1926 specifies dimensions, performance requirements, and test procedures for adjustable and nonadjustable heavy-duty (S series) stud ends with ASME B1.1 threads for use in fluid power and general applications and the O-rings used with them that are currently not listed in SAE J515. Stud ends in accordance with this part of SAE J1926 may be used at working pressures up to 63 MPa for nonadjustable stud ends and up to 41.3 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc. For threaded ports and stud ends specified in new designs for hydraulic fluid power applications, only ISO 6149 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and ISO 11926 shall not be used for new design in hydraulic fluid power applications. Conformance to the dimensional information does not guarantee rated performance.
Standard

Connections for General Use and Fluid Power—Ports and Stud Ends with ASME B1.1 Threads and O-Ring Sealing—Part 2: Heavy-Duty (S Series) Stud Ends

2010-03-12
HISTORICAL
J1926/2_201003
This part of SAE J1926 specifies dimensions, performance requirements, and test procedures for adjustable and nonadjustable heavy-duty (S series) stud ends with ASME B1.1 threads for use in fluid power and general applications and the O-rings used with them that are currently not listed in SAE J515. Stud ends in accordance with this part of SAE J1926 may be used at working pressures up to 63 MPa for nonadjustable stud ends and up to 41.3 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc. For threaded ports and stud ends specified in new designs for hydraulic fluid power applications, only ISO 6149 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and ISO 11926 shall not be used for new design in hydraulic fluid power applications. NOTE: This document specifies inch as well as metric hexes for the stud ends.
Standard

Connections for General Use and Fluid Power - Ports and Stud Ends with ASME B1.1 Threads and O-Ring Sealing - Part 2: Heavy-Duty (S Series) Stud Ends

1993-03-01
HISTORICAL
J1926/2_199303
This part of SAE J1926 specifies dimensions, performance requirements, and test procedures for adjustable and nonadjustable heavy-duty (S series) stud ends with ISO 725 threads for use in fluid power and general applications and the O-rings used with them. Stud ends in accordance with this part of SAE J1926 may be used at working pressures up to 63 MPa for nonadjustable stud ends and up to 40 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc. For threaded ports and stud ends specified in new designs for hydraulic fluid power applications, only SAE J2244 (ISO 6149) shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and ISO 11926 shall not be used for new design in hydraulic fluid power applications. Conformance to the dimensional information does not guarantee rated performance.
Standard

Metallic Tube Connections for Fluid Power and General Use - Test Methods for Threaded Hydraulic Fluid Power Connectors *HS-150/2000*

1998-10-01
HISTORICAL
J1644_199810
This SAE Standard specifies uniform methods for the testing and performance evaluation of threaded metallic tube connections and stud ends of ports for hydraulic fluid power. Tests outlined within this document are independent of each other and document the method to follow for each test; see the appropriate component SAE or ISO standard for the test(s) requirements and the performance criteria. Appendix A of SAE J1644 is normative; Appendix B is informative.
Standard

Metallic Tube Connections for Fluid Power and General Use - Test Methods for Threaded Hydraulic Fluid Power Connectors

1993-05-01
HISTORICAL
J1644_199305
This SAE Standard specifies uniform methods for the testing and performance evaluation of threaded metallic tube connections and stud ends of ports for hydraulic fluid power. Tests outlined within this document are independent of each other and document the method for follow for each test; see the appropriate component SAE or ISO standard for the test(s) requirements and the performance criteria.
Standard

Metallic Tube Connections for Fluid Power and General Use--Test Methods for Threaded Hydraulic Fluid Power Connectors

2007-08-14
CURRENT
J1644_200708
This SAE Standard specifies uniform methods for the testing and performance evaluation of threaded metallic tube connections and stud ends of ports for hydraulic fluid power. Tests outlined within this document are independent of each other and document the method to follow for each test; see the appropriate component SAE or ISO standard for the test(s) requirements and the performance criteria. Appendix A of SAE J1644 is normative; Appendix B is informative.
Standard

Fitting--O-Ring Face Seal

1987-02-01
HISTORICAL
J1453_198702
This SAE Standard covers material, dimensional, and performance requirements of steel O-ring face seal fittings for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube or hose diameters 6.35 mm (0.250 in) through 38.1 mm (1.500 in). These fittings are intended for general application and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These fittings are capable of providing leak-proof full flow connections in hydraulic systems operating from 95 kPa (28 in Hg) vacuum to working pressures shown in Table 1. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, these values should not be construed as guaranteed minimums.
Standard

Fitting--O-Ring Face Seal

1987-07-01
HISTORICAL
J1453_198707
This SAE Standard covers material, dimensional, and performance requirements of steel O-ring face seal fittings for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube or hose diameters 6.35 mm (0.250 in) through 38.1 mm (1.500 in). These fittings are intended for general application and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These fittings are capable of providing leak proof full flow connections in hydraulic systems operating from 95 kPa (28 in Hg) vacuum to working pressures shown in Table 1. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, these values should not be construed as guaranteed minimums.
Standard

Fitting--O-Ring Face Seal

1991-06-01
HISTORICAL
J1453_199106
This SAE Standard covers material, dimensional, and performance requirements of steel O-ring face seal fittings for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube or hose diameters 6.35 mm (0.250 in) through 38.1 mm (1.500 in). These fittings are intended for general application and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These fittings are capable of providing leak-proof full flow connections in hydraulic systems operating from 95 kPa (28 in Hg) vacuum to working pressures shown in Table 1. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, these values should not be construed as guaranteed minimums.
Standard

Fitting--O-Ring Face Seal

1988-01-01
HISTORICAL
J1453_198801
This SAE Standard covers material, dimensional, and performance requirements of steel O-ring face seal fittings for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube or hose diameters 6.35 mm (0.250 in) through 38.1 mm (1.500 in). These fittings are intended for general application and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These fittings are capable of providing leak-proof full flow connections in hydraulic systems operating from 95 kPa (28 in Hg) vacuum to working pressures shown in Table 1. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, these values should not be construed as guaranteed minimums.
Standard

Fitting--O-Ring Face Seal

1992-06-01
HISTORICAL
J1453_199206
This SAE Standard covers material, dimensional, and performance requirements of steel O-ring face seal fittings for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube or hose diameters 6.35 mm (0.250 in) through 38.1 mm (1.500 in). These fittings are intended for general application and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These fittings are capable of providing leak-proof full flow connections in hydraulic systems operating from 95 kPa (28 in Hg) vacuum to working pressures shown in Table 1. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, these values should not be construed as guaranteed minimums.
Standard

Fitting--O-Ring Face Seal

1997-05-01
HISTORICAL
J1453_199705
This SAE Standard covers material, dimensional, and performance requirements of steel O-ring face seal fittings for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube or hose diameters 6.35 mm (0.250 in) through 38.1 mm (1.500 in). These fittings are intended for general application and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These fittings are capable of providing leak-proof full flow connections in hydraulic systems operating from 95 kPa (28 in Hg) vacuum to working pressures shown in Table 1. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, these values should not be construed as guaranteed minimums.
Standard

Fitting--O-Ring Face Seal

1989-06-01
HISTORICAL
J1453_198906
This SAE Standard covers material, dimensional, and performance requirements of steel O-ring face seal fittings for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube or hose diameters 6.35 mm (0.250 in) through 38.1 mm (1.500 in). These fittings are intended for general application and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These fittings are capable of providing leak-proof full flow connections in hydraulic systems operating from 95 kPa (28 in Hg) vacuum to working pressures shown in Table 1. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, these values should not be construed as guaranteed minimums.
Standard

Fitting--O-Ring Face Seal

1996-06-01
HISTORICAL
J1453_199606
This SAE Standard covers material, dimensional, and performance requirements of steel O-ring face seal fittings for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube or hose diameters 6.35 mm (0.250 in) through 38.1 mm (1.500 in). These fittings are intended for general application and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These fittings are capable of providing leak-proof full flow connections in hydraulic systems operating from 95 kPa (28 in Hg) vacuum to working pressures shown in Table 1. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, these values should not be construed as guaranteed minimums.
Standard

Fitting--O-Ring Face Seal

1993-06-01
HISTORICAL
J1453_199306
This SAE Standard covers material, dimensional, and performance requirements of steel O-ring face seal fittings for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube or hose diameters 6.35 mm (0.250 in) through 38.1 mm (1.500 in). These fittings are intended for general application and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These fittings are capable of providing leak-proof full flow connections in hydraulic systems operating from 95 kPa (28 in Hg) vacuum to working pressures shown in Table 1. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, these values should not be construed as guaranteed minimums.
Standard

Fitting--O-Ring Face Seal

1994-06-01
HISTORICAL
J1453_199406
This SAE Standard covers material, dimensional, and performance requirements of steel O-ring face seal fittings for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube or hose diameters 6.35 mm (0.250 in) through 38.1 mm (1.500 in). These fittings are intended for general application and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These fittings are capable of providing leak-proof full flow connections in hydraulic systems operating from 95 kPa (28 in Hg) vacuum to working pressures shown in Table 1. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, these values should not be construed as guaranteed minimums.
X