Search Results

The effect of injection pressure ranging from 100 to 300MPa on the ignition, flame development and soot formation characteristics of biodiesel fuel spray using a common rail injection system for direct injection (D.I.) diesel engine was investigated. Experiments were carried out in a constant volume vessel under conditions similar to the real engine condition using a single hole nozzle. Biodiesel fuels from two sources namely; palm oil (BDFp) and cooked oil (BDFc) with the commercial JIS#2diesel fuel were utilized in this research. The OH chemiluminescence technique was used to determine the ignition and the lift-off length of the combusting flame. The natural luminosity technique was applied to study the flame development and the two color pyrometry was applied for the soot formation processes. Ignition delay decreased as the injection pressure progressed from 100 to 300MPa. This was as a result of the enhanced mixing achieved at higher injection pressures.

Ethanol is regarded as the promising alternative fuel for gasoline to meet the strict low emission standard for spark ignition engines. In this study, the spray mixture formation process for different ethanol blended fuels, including E0 (gasoline), E85 (85% volume of ethanol and 15% volume of gasoline) and E100 (ethanol), has been evaluated using hole-type nozzle by the measurement of Laser Absorption Scattering (LAS) technique in a constant volume vessel. Based on the principle of LAS, the quantitative vapor and liquid phase distribution from different ethanol blended fuel can be obtained by the light extinction regime. Aiming to analyze the effect of mixture formation and evaporation for different components of blended fuel or pure gasoline and ethanol, the vapor distribution of gasoline was determined by using p-xylene, which had similar physical properties to gasoline, especially higher boiling temperature components, and higher absorption for ultraviolet.

To reduce carbon dioxide emission and to relieve the demand of fossil fuels, ethanol is regarded as one of the most promising alternative fuels for gasoline. Recently, using ethanol in the state-of-the-art gasoline engine, direct-injection spark-ignition (DISI) engine, has become more attention by researchers due to less knowledge of the ignition and combustion processes in that engine. In this study, different ethanol-gasoline blended fuels, E0 (100% gasoline), E85 (85% ethanol and 15% gasoline mixed in volume basis) and E100 (100% ethanol) were injected by a valve-covered-orifice (VCO) hole-type nozzle. The experimental environment was set to the condition similar with the near top dead center (TDC) in DISI engine. The high-speed imaging of shadowgraph, OH* chemiluminescence and flame natural luminosity were used to clarify the characteristics of the ignition process, flame development and propagation.

This paper studies the ignition processes of two biodiesel from two different feedstock sources, namely waste cooked oil (WCO) and palm oil (PO). They were investigated using the direct photography through high-speed video observations and detailed chemical kinetics. The detailed chemical kinetics modeling was carried out to complement data acquired using the high-speed video observations. For the high-speed video observations, an image intensifier combined with OH* filter connected to a high-speed video camera was used to obtain OH* chemiluminscence image near 313 nm. The OH* images were used to obtain the experimental ignition delay of the biodiesel fuels. For the high-speed video observations, experiments were done at an injection pressure of 100, 200 and 300 MPa using a 0.16 mm injector nozzle.

Hydrogen (H2) addition is widely used for natural gas combustion to improve the engine efficiency. However, less attention was paid on the various ignition timings for the maximum brake torque (MBT) and brake thermal efficiency (BTE). In order to check the ignition timing effect, experiments were performed in a spark ignition engine with engine speed fixed on 1500 revolutions per minute (rpm). Firstly, CH4 was only used for combustion with excess air ratio (λ) changing from 0.8 to 1.4. Then, co-combustion of 50 vol% CH4 and 50 vol% CO2 was checked to simulate methane fermentation gas. Finally, H2 was added with volume percentage varying from 5% to 20%. Among these discussions, torque, brake mean effective pressure (BMEP), BTE and cylinder pressure were evaluated. Based on the results, high efficiency can be achieved by advancing the ignition timing with H2 addition at λ=1.4. However, with H2 addition, the ignition timing should be retarded to obtain higher BTE.

Among the alternative fuels, dimethyl ether (DME), one of the oxygenated fuels, attracts attention as an alternative fuel for the Diesel engine since the properties of the DME are fitted to the Diesel engine combustion and the know-how development has been made of the mass production of the DME from a natural gas. In this study, experiments were performed of ignition characteristics of the DME and Diesel fuel sprays injected by a D.I. Diesel injector into a high-pressure, high-temperature vessel. The fuel injection was made by a Bosch type injection system. A schlieren optical system was adopted for visualizing the ignition process as well as the vaporization process of the DME and Diesel fuel sprays. The ignition delay was measured by using a photo-sensor which had a sensitivity in the wavelength range from visible to ultraviolet. Pressure and temperature of the ambient air and the oxygen concentration of the ambient air were changed as experimental parameters.

The fuel injection characteristics of Dimethyl Ether(DME) were calculated and compared with the calculated results of diesel fuel using a simulation model of an in-line diesel injection system in order to clarify the differences between the injection characteristics of the two fuels. Moreover, numerical analyses for the DME injection were performed while changing the fuel parameters and the injection system parameters in order to estimate the effects of these parameters on the fuel injection characteristics. The effects of some of these parameters were evaluated by experimental results conducted in a constant volume vessel. Furthermore, the spray tip penetration was calculated using the computed results of the injection pressure. As a result of this study, the injection characteristics of the DME fuel are basically confirmed. By the macroscopic analyses of these spray characteristics, the DME spray behavior in a combustion chamber can be estimated.

Different ethanol-gasoline blended fuels, namely the E0 (100% gasoline), E85 (85% ethanol and 15% gasoline mixed in volume basis) and E100 (100% ethanol) were injected by a valve-covered-orifice (VCO) hole-type nozzle in a condition simulating the near top dead center (TDC). Two typical injection pressures of 10 and 20MPa were adopted to clarify the spray and flame behaviors. The correlation of the upstream unburned fuel and the flame propagation was analyzed by the high-speed imaging of shadowgraph. Moreover, the effects of ignition timing and location on the flame propagation were discussed based on the imaging of OH* chemiluminescence.

Spray combustion processes of palm oil biodiesel (PO) and conventional diesel fuels were simulated using the CONVERGE CFD code. Thermochemical and reaction kinetic data (115 species and 460 reactions) by Luo et al. (2012) and Lu et al. (2009) (68 species and 283 reactions) were implemented in the CONVERGE CFD to simulate the spray and combustion processes of the two fuels. Tetradecane (C14H30) and n- heptane (C7H16) were used as surrogates for diesel. For the palm biodiesel, the mixture of methyl decanoate (C11H20O2), methyl-9-decenoate (C11H19O2) and n-heptane was used as surrogate. The palm biodiesel surrogates were combined in proportions based on the previous GC-MS results for the five major biodiesel components namely methyl palmitate, methyl stearate, methyl oleate, methyl linoleate and methyl linolenate.