Refine Your Search

Date

Date

Automotive Vehicles and equipment Truck and Bus Wheel Committee

Search Results

Viewing 1 to 20 of 29
12Next >Last >>
Sort by relevance
Standard

Inboard Mounted Disc Brake Rotor/Disc Wheel Hub Interface Dimensions - Commercial Vehicles
2012-05-29
HISTORICAL
J2696_201205
This SAE Recommended Practice establishes dimensions and tolerances for the interface between inboard mounted disc brake rotors and disc wheel hubs. The geometric features described in this document are shown at true position. This document is intended for inboard mounted disc brake rotors and disc wheel hubs for Class 5, 6, 7, and 8 commercial vehicles. Special and less common applications are not covered.
Standard

Inboard Mounted Disc Brake Rotor/Disc Wheel Hub Interface Dimensions - Commercial Vehicles
2019-09-03
HISTORICAL
J2696_201909
This SAE Recommended Practice establishes dimensions and tolerances for the interface between inboard mounted disc brake rotors and disc wheel hubs. This document is intended for inboard mounted disc brake rotors and disc wheel hubs for Class 5, 6, 7, and 8 commercial vehicles. Special and less-common applications are not covered.
Standard

Setting Preload in Heavy-Duty Wheel Bearings
2001-03-01
HISTORICAL
J2535_200103
This SAE Recommended Practice applies to the four primary, large volume applications in the class 7-8 heavy-duty market place, as specified in SAE J1842: a “N” trailer axle b “R” powered rear axle c “FF / FG” nonpowered front axle d “P” trailer axle This document applies to on-highway, disc wheel / outboard drum brake applications. It is not applicable to those applications that exceed the GAWR ratings or the load line restrictions listed in columns “A,” “B,” and “C” of Table 1. Load lines are measured from the inboard bearing cup backface as shown in 3.4. This document establishes preload force values only. The methodology to obtain these force values must be determined by the fastener supplier and/or axle assembler. This document reviews the bearing system. It is NOT intended to prescribe (new or existing) axle and/or hub manufacturers’ ratings and/or specifications.
Standard

Fatigue Test Procedures: Hubs and Wheels for Demountable Rims
2009-10-12
HISTORICAL
J1095_200910
This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing of wheels for demountable rims and hubs intended for normal highway use on trucks, buses, truck trailers, and multipurpose passenger vehicles. The hubs included have bolt circle diameters from 165.1 to 335.0 mm (6.50 to 13.19 in). It is up to each hub and/or wheel for demountable rims developer to determine what test method, accelerated load factor and cycle life requirements are applicable to obtain satisfactory service life in a given application. When deviations from the procedures recommended herein are made, it is the responsibility of the hub and/or wheel for demountable rims developer to modify other parameters to obtain satisfactory service life.
Standard

SPOKE WHEELS AND HUB FATIGUE TEST PROCEDURES
1995-03-01
HISTORICAL
J1095_199503
This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing of spoke wheels and hubs intended for normal highway use on trucks, buses, truck trailers, and multipurpose passenger vehicles. The hubs included have bolt circle diameters from 165.1 to 335.0 mm (6.50 to 13.19 in). The tests described in this document are not to be construed as the only tests required or permitted to ensure that a spoke wheel or a hub will perform satisfactorily for its intended use.
Standard

SPOKE WHEELS AND HUB FATIGUE TEST PROCEDURES
1991-01-01
HISTORICAL
J1095_199101
This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing of spoke wheels and hubs intended for normal highway use on trucks, buses, truck trailers, and multipurpose passenger vehicles. The hubs included have bolt circle diameters from 165.1 to 335.0 mm (6.50 to 13.19 in). The tests described in this document are not to be construed as the only tests required or permitted to assure that a spoke wheel or a hub will perform satisfactorily for its intended use.
Standard

Fatigue Test Procedures: Hubs and Wheels for Demountable Rims
2021-05-06
CURRENT
J1095_202105
This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing of wheels for demountable rims and hubs intended for normal highway use on trucks, buses, truck trailers, and multipurpose passenger vehicles. The hubs included have bolt circle diameters ranging from 165.1 to 335.0 mm (6.500 to 13.189 inches). It is up to each hub and/or wheel for demountable rims manufacturer to determine the appropriate test method, accelerated load factor and cycle life requirements applicable to obtain satisfactory service life for a given application. When deviations from the procedures recommended herein are made, it is the responsibility of the hub and/or wheel for demountable rims developer to modify other parameters as necessary to ensure satisfactory service life for the intended application. It should be noted that this test procedure focuses on fatigue resulting from vehicle loading and cornering forces.
Standard

Fatigue Test Procedures: Hubs and Wheels for Demountable Rims
2016-06-30
HISTORICAL
J1095_201606
This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing of wheels for demountable rims and hubs intended for normal highway use on trucks, buses, truck trailers, and multipurpose passenger vehicles. The hubs included have bolt circle diameters from 165.1 to 335.0 mm (6.500 to 13.189 in). It is up to each hub and/or wheel for demountable rims manufacturer to determine what test method, accelerated load factor and cycle life requirements are applicable to obtain satisfactory service life in a given application. When deviations from the procedures recommended herein are made, it is the responsibility of the hub and/or wheel for demountable rims developer to modify other parameters to obtain satisfactory service life.
Standard

Wide Base Disc Wheels and Demountable Rims
2000-04-26
HISTORICAL
J876_200004
This SAE Recomended Practice establishes uniform engineering nomenclature for wide base disc wheels and demountable rims. This nomenclature and accompanying figures are intended to define fundamental wide base disc wheels and demountable rim terms. The dimensions given are those necessary to maintain serviceability and interchangeability of the wide base disc wheels and demountable rims with standard hardware.
Standard

DISC WHEEL/HUB OR DRUM INTERFACE DIMENSIONS—COMMERCIAL VEHICLES
1997-07-01
HISTORICAL
J694_199707
This SAE Recommended Practice contains dimensions and their tolerances concerning disc wheel to hub or drum interface areas for commercial vehicles and multipurpose passenger vehicles. Stamped disc wheels for single applications and special or less common applications are not covered in this document.
Standard

Disc Wheel/Hub or Drum Interface Dimensions—Commercial Vehicles
1998-08-01
HISTORICAL
J694_199808
This SAE Recommended Practice contains dimensions and their tolerances concerning disc wheel to hub or drum interface areas for commercial vehicles and multipurpose passenger vehicles. Stamped disc wheels for single applications and special or less common applications are not covered in this document.
Standard

OUTBOARD MOUNTED BRAKE DRUM/DISC WHEEL HUB INTERFACE DIMENSIONS—COMMERCIAL VEHICLES
1997-06-01
HISTORICAL
J1671_199706
This SAE Recommended Practice contains dimensions and tolerances for outboard mounted brake drums and disc wheel hubs in the interface areas. The geometric features described in this document are shown at true position. This document is intended for outboard mounted brake drums and disc wheel hubs used on Class 7 and 8 commercial vehicles. Special and less common applications are not covered.
Standard

ABS Excitor Ring Location Standardization
1999-10-09
HISTORICAL
J1730_199910
This SAE Recommended Practice is to establish the Antilock Brake System (ABS) sensor interface and envelope dimensions for standardizing the location of the Antilock Brake System (ABS) rings mounted on the inner end of the hub on the following axle designations. a FF front b FL front c L powered rear d R powered rear e U powered rear f W powered rear g N trailer h P trailer
Standard

ABS EXCITOR RING LOCATION STANDARDIZATION
1996-10-01
HISTORICAL
J1730_199610
This SAE Recommended Practice is to establish the Antilock Brake System (ABS) sensor interface and envelope dimensions for standardizing the location of the Antilock Brake System (ABS) rings mounted on the inner end of the hub on the following axle designations: a FF/FG front b FL front c L powered rear d R powered rear e N trailer f P trailer
Standard

NOMENCLATURE—WHEELS, HUBS, AND RIMS FOR COMMERCIAL VEHICLES
1991-10-09
HISTORICAL
J393_199110
This SAE Recommended Practice establishes uniform engineering nomenclature for wheels, rims, and their components used in truck, bus, and trailer applications. This nomenclature and accompanying drawings are intended to define fundamental truck wheel, hub, and rim terms rather than to provide a comprehensive tabulation of all wheel, hub, and rim designs. The International Standard (ISO) nomenclature is shown in parentheses when different than SAE J393.
Standard

Wheel End Assembly and Axle Spindle Interface Dimensions - Truck and Bus
2020-02-13
CURRENT
J2475_202002
This recommended practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include axle spindle, spindle threads, bearing cones, bearing spacer, seal, and wheel hub. This recommended practice is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, FL, I80, L, N, P, R, U, and W.
Standard

Wheel End Assembly and Axle Spindle Interface Dimensions—Commercial Vehicles
2000-01-24
HISTORICAL
J2475_200001
This SAE Recommended Practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include bearing cones, bearing spacers, and wheel hubs. This document is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, R, N, and P. SAE configurations FC, FL, K, L, U, and W are not included, but may be added in the future.
Standard

Wheel End Assembly and Axle Spindle Interface Dimensions—Truck and Bus
2008-08-22
HISTORICAL
J2475_200808
This recommended practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include axle spindle, bearing cones, bearing spacer, seal and wheel hub. This recommended practice is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, FL, I80, L, U, W, R, N and P.
12Next >Last >>
X