Refine Your Search

Topic

Author

Affiliation

Search Results

Collection

Multi-Dimensional Engine Modeling, 2018

2018-04-03
This collection covers advances in the development and application of models and tools involved in multi-dimensional engine modeling: advances in chemical kinetics, combustion and spray modeling, turbulence, heat transfer, mesh generation, and approaches targeting improved computational efficiency. Papers employing multi-dimensional modeling to gain a deeper understanding of processes related to turbulent transport, transient phenomena, and chemically reacting, two-phase flows are included in this collection.
Standard

In-line, Elbow, and Tee Flanged Connectors for use with SAE J518-1/ISO6162-1 Components

2015-02-03
WIP
J518/4
This document standardizes the design of connector blocks used for joining SAE J518-1/ISO 6162-1 (Code 61) flange heads with other SAE J518-1/ISO 6162-1 (Code 61) flange heads with straight, elbow, and tee geometries. The blocks specified in this document are designed to provide for very compact installations. As a result, the tap depths specified in this document do not conform to those specified in SAE J518-1/ISO 6162-1 to allow for a minimal bend radius in the elbow and tee configurations. This document specifies both inch and metric configurations
Standard

Round Head Bolts

1990-01-01
CURRENT
J481_199001
Round head bolts are made in two body styles: (a) A full size body, with a maximum diameter somewhat greater than the nominal diameter (not an SAE Standard except for ribbed neck bolts, Table 3); and (b) an undersize body, with a minimum diameter approximating the pitch diameter of the thread and a maximum diameter never exceeding nominal (SAE standard for all types except ribbed neck bolts). The body diameter of either style may be exceeded by a reasonable swelling or fin under the head, or under corners of the square necks, to the extent that serviceability is not affected.
Standard

Cotter Pins

1990-01-01
CURRENT
J487_199001
Not available.
Standard

Alignment of Nut Slots

1990-01-01
CURRENT
J484_199001
This method of gaging alignment of nut slots allows equal variations for location of the cotter pin hole in the bolt and location of slots in the nut. To inspect the nut, the slotted gage is inserted through the nut hole from the bearing surface of the nut. Alignment of slots is considered satisfactory if the gage pin can be slipped into the gage and nut slots without interference.
Standard

Low Collapse Pressure Hydraulic Filter Element – 380 L/min Flow, 3.5 MPa Collapse Pressure, Filtration Ratio = ?? at xx µm

2013-01-02
WIP
J2321/4
This specification sheet establishes requirements for a low collapse pressure configuration filter element of a specific configuration with a minimum filtration ratio of 75 for particles larger than ? μm when designed and tested in accordance with SAE J2321 and this specification sheet. Note: The efficiency and dirt capacity have not yet been determined..
Standard

Spark Plugs-Test Methods

2016-10-24
WIP
J3132
This SAE Standard specifies the minimum performance recommendation for spark plugs intended for use in various internal combustion engines including Automotive, Marine, Motorcycle and Utility engine applications. This standard is not intended to supply information for spark plugs used in aircraft applications of any type.
Standard

Procedure for Mapping Fuel Consumption for small spark ignited engines

2017-03-22
WIP
J3139
The purpose of this SAE Standard is to provide a standardized test procedure for measuring the fuel consumption of spark ignited engines in the range of 225-999cc used in the consumer and commercial turf industry. The load points and associated fuel consumption rates will be measured as the engine operates on the engine speed governor, reflecting how the user will operate the equipment. The fuel consumption calculated in gallons of useage per hour will be derived from a specified engine speed and load map to be communicated universally to end users.
Standard

Electric Park Brake Sizing

2017-10-16
WIP
J3158
The scope of this new recommended practice should include, but not necessarily be limited to: 1. Define vehicle operating conditions used to drive MOC-EPB actuator design and selection 2. Define brake corner operating conditions (e.g. temperature and state of burnish) used to drive MOC-EPB actuator design and selection 3. Define actuator operating conditions (e.g. temperature, voltage, current limit, and state of wear) used to drive MOC-EPB actuator design and selection 4. Define methodology for addressing part to part variation in performance
Standard

Hydrocarbon Adsorber Test Procedure

2010-09-01
WIP
J2952
This SAE Recommended Practice describes several procedures to test and measure the performance of a Hydrocarbon Adsorber device located in a vehicle air induction system and attempts to simulate various loading and purging cycles it could experience. The Hydrocarbon Adsorber device is used to adsorb the small amount of gasoline that is volatized in the air induction manifold after the vehicle engine is turned off. This gasoline vapor can travel through the air induction system and escape to the atmosphere, impacting the total allowable vehicle evaporative emissions level set by the EPA and California ARB. When the vehicle is restarted, the Hydrocarbon Adsorber device is purged of hydrocarbons with the fresh air flow and is designed to perform as life of the vehicle emission device as set by the EPA.
Standard

Impact testing of automotive fuel tanks

2008-06-26
WIP
J2852
Drop testing and "sled" testing are used regularly to demonstrate integrity of plastic fuel systems. This document defines test method, application and rationale for fuel tank impact testing.
Standard

Fatigue LIfe Procedure for Wet Friction Materials

2011-04-05
WIP
J2968
This specification would cover standards for performing wet friction material fatigue life determination. It would include recommendations on equipment, sample preparation, and results reporting
X