Refine Your Search

Topic

Author

Search Results

Technical Paper

Effects of Load on Emissions and NOx Trap/Catalyst Efficiency for a Direct Injection Spark Ignition Engine

1999-05-03
1999-01-1528
A 1998 Toyota Corona passenger car with a direct injection spark ignition (DISI) engine was tested at constant engine speed (2000 rpm) over a range of loads. Engine-out and tailpipe emissions of gas phase species were measured each second. This allowed examination of the engine-out emissions for late and early injection. Regeneration of the lean NOx trap/catalyst was also examined, as was the efficiency of NOx reduction. NOx stored in the trap/catalyst is released at the leading edge of regenerations, such that the tailpipe NOx is higher than the engine-out NOx for a brief period. The efficiency of NOx reduction was <50% for the lowest loads examined. As the load increased, the efficiency of NOx reduction decreased to near 0% due to excessive catalyst temperatures. Loads sufficiently high to require a rich mixture produce high NOx reduction efficiencies, but in this case the NOx reduction occurs via the three-way catalysts on this vehicle.
Technical Paper

Emissions and Fuel Economy of a 1998 Toyota with a Direct Injection Spark Ignition Engine

1999-05-03
1999-01-1527
A 1998 Toyota Corona passenger car with a direct injection spark ignition (DISI) engine was tested via a variety of driving cycles using California Phase 2 reformulated gasoline. A comparable PFI vehicle was also evaluated. The standard driving cycles examined were the Federal Test Procedure (FTP), Highway Fuel Economy Test, US06, simulated SC03, Japanese 10-15, New York City Cycle, and European ECE+EDU. Engine-out and tailpipe emissions of gas phase species were measured each second. Hydrocarbon speciations were performed for each phase of the FTP for both the engine-out and tailpipe emissions. Tailpipe particulate mass emissions were also measured. The results are analyzed to identify the emissions challenges facing the DISI engine and the factors that contribute to the particulates, NOx, and hydrocarbon emissions problems of the DISI engine.
Technical Paper

Effect of Fuel Parameters on Emissions from a Direct Injection Spark Ignition Engine During Constant Speed, Variable Load Tests

2000-06-19
2000-01-1909
A 1998 Toyota Corona passenger car with a direct injection spark ignition (DISI) engine was tested at constant engine speed (2000 rpm) over a range of loads. Engine-out and tailpipe emissions of gas phase species were measured each second. This allowed examination of the engine-out emissions for late and early injection. Seven fuels were used for these tests: five blended fuels and two pure hydrocarbon fuels. These seven fuels can be divided into groups for examination of the effects of volatility, MTBE, and structure (an aromatic versus an i-alkane). Correlations between the fuel properties and their effects on emissions are presented. Use of steady state tests rather than driving cycles to examine fuel effects on emissions eliminates the complications resulting from accelerations, decelerations, and changes of injection timing but care had to be taken to account for the periodic regenerations of the lean NOx trap/catalyst.
Technical Paper

Effects of Fuel Parameters on FTP Emissions of a 1998 Toyota with a Direct Injection Spark Ignition Engine

2000-06-19
2000-01-1907
The effects of fuel properties on the emissions of a production vehicle with a gasoline direct injection engine operating over the Federal Test Procedure (FTP) cycle were investigated. The vehicle used was a 1998 Toyota Corona passenger car with a direct injection spark ignition (DISI) engine. Engine-out and tailpipe FTP emissions for six fuels and a California Phase 2 RFG reference fuel are presented. Four of the test fuels were blended from refinery components to meet specified distillation profiles. The remaining test fuels were iso-octane and toluene, an iso-alkane and an aromatic with essentially the same boiling point (at atmospheric pressure) that is near the T50 point for the blended fuels. Statistically significant effects, at the 95% confidence level, of the fuels on tailpipe emissions were found. Correlations were sought between the properties of the five blends and the Emissions Indices for engine-out hydrocarbons and NOx and for tailpipe particulates.
Technical Paper

Effect of Fuel Parameters on Speciated Hydrocarbon Emissions from a Direct Injection Spark Ignition Engine

2000-06-19
2000-01-1908
A 1998 Toyota Corona passenger car with a direct injection spark ignition (DISI) engine was tested over the Federal Test Procedure (FTP) driving cycle. Speciated engine-out hydrocarbon emissions were measured. Seven fuels were used for these tests: five blended fuels and two pure hydrocarbon fuels. One of the blended fuels was CARB Phase 2 reformulated gasoline which was used as the reference fuel. The remaining four blended fuels were made from refinery components to meet specified distillation profiles. The pure hydrocarbon fuels were iso-octane and toluene - an alkane and an aromatic with essentially identical boiling points. The five blended fuels can be grouped to examine the effects of fuel volatility and MTBE. Additionally, correlations were sought between the fuel properties and the Specific Reactivity, the exhaust “toxics”, and the pass-through of unburned fuel species.
Technical Paper

The Effects of In-Cylinder Flow Fields and Injection Timing on Time-Resolved Hydrocarbon Emissions in a 4-Valve, DISI Engine

2000-06-19
2000-01-1905
Direct injection spark-ignition (DISI) engines have been shown to have much higher engine-out hydrocarbon emissions (HC) than port fuel injected (PFI) engines. A major contribution to the increase in HC emissions is from the in-cylinder surface wetting that occurs as the fuel is injected. A previous study using an optical access engine and a fuel concentration probe demonstrated that the in-cylinder flow field and injection timing have a significant effect on the equivalence ratio at the spark plug. This study continues that work, by using a fast spectroscopic HC emission measurement device (Fast-Spec) to study time-resolved HC emissions from a 4-valve, centrally injected, single cylinder DISI engine. Three flow fields are studied: tumble, reverse tumble and stock. The tumble and reverse tumble flow fields are achieved using shrouded valves. Both early and late start of injection (SOI) timings are investigated.
Technical Paper

Refinement of a Dedicated E85 1999 Silverado with Emphasis on Cold Start and Cold Drivability

2001-03-05
2001-01-0679
The University of Texas 2000 Ethanol Vehicle Challenge team remains focused on cold start, cold drivability, fuel economy, and emissions reduction for our 2000 Ethanol Vehicle Challenge entry. We used the stock PCM for all control functions except control of an innovative cold-start system our team designed. The primary modifications for improved emissions control involved ceramic coating of the exhaust manifolds, use of close-coupled ethanol-specific catalysts, use of a moddified version of the California Emissions Calibrated PCM, and our cold-start system that eliminates the need to overfuel the engine at the beginning of the FTP. Additionally, we eliminated EGR at high load to improve power density. Major modifications, such as increasing the compression ratio or pressure boosting, were eliminated from consideration due to cost, complexity, reliability, or emissions penalties.
Technical Paper

In-Situ Mapping and Analysis of the Toyota Prius HEV Engine

2000-08-21
2000-01-3096
The Prius is a major achievement by Toyota: it is the first mass-produced HEV with the first available HEV-optimized engine. Argonne National Laboratory's Advanced Powertrain Test Facility has been testing the Prius for model validation and technology performance and assessment. A significant part of the Prius test program is focused on testing and mapping the engine. A short-length torque sensor was installed in the powertrain in-situ. The torque sensor data allow insight into vehicle operational strategy, engine utilization, engine efficiency, and specific emissions. This paper describes the design and process necessary to install a torque sensor in a vehicle and shows the high-fidelity data measured during chassis dynamometer testing. The engine was found to have a maximum thermodynamic efficiency of 36.4%. Emissions and catalyst efficiency maps were also produced.
Technical Paper

Conversion of a 1999 Silverado to Dedicated E85 with Emphasis on Cold Start and Cold Driveability

2000-03-06
2000-01-0590
The University of Texas Ethanol Vehicle Challenge team focused upon cold start/driveability, fuel economy, and emissions reduction for our 1999 Ethanol Vehicle Challenge entry. We replaced or coated all fuel system components that were not ethanol compatible. We used the stock PCM for all control functions except control of a novel cold-start system our team designed. The primary modifications for improved emissions control involved ceramic coating of the exhaust manifolds, use of close-coupled ethanol-specific catalysts, increased EGR for the operating conditions of the five longest cruises on the FTP, and our cold-start system that eliminates the need to overfuel the engine at the beginning of the FTP. This EGR control scheme should also benefit urban fuel economy. Additionally, we eliminated EGR at high load to improve power density.
Technical Paper

Investigation of a Novel Aid for Cold Starting of Diesels

1989-02-01
890041
An experimental investigation of the use of an engine coolant exchange system for prewarming diesel engines before cold starting is discussed. This coolant exchange system involves connecting the coolant system of a fully warmed-up and running engine (e.g., a spark ignition engine) to that of the cold diesel to be started using hydraulic hoses with quick connect fittings and an auxiliary pump. The investigation was performed using a 4,3 liter V6 indirect injection diesel engine since this represents a difficult case for cold starting. The starting characteristics using the coolant exchange technique are compared to those using the production glow plug system, which includes a fuel heater and afterglow. It is shown that the coolant exchange system allows this engine to be started down to −26 °C, much colder than the −13°C limit for the production glow plug system.
Technical Paper

Initial Studies of a New Type of Ignitor: The Railplug

1991-10-01
912319
Initial investigations of a new type of high energy ignitor for I.C. engines are described. The ignitor is a miniaturized railgun, or “railplug.” The railplug produces a relatively large mass of high velocity plasma. These characteristics may be advantageous for initiating combustion in a number of different applications. Unlike a plasma jet ignitor, the railplug plasma is driven not only by thermodynamic expansion, but by electromagnetic forces as well. Four experimental railplug designs were evaluated using schlieren and shadowgraphy visualization to examine plasma movement and shape. Railplug current and voltage were also measured. One railplug consisting of two unenclosed parallel rails was used to demonstrate the electromagnetically induced motion of the plasma at ambient conditions. Schlieren photos showed that the plasma plume moves strongly in the direction of the electromagnetic Lorentz forces.
Technical Paper

Intake and ECM Submodel Improvements for Dynamic SI Engine Models: Examination of Tip-In/Tip-Out

1991-02-01
910074
Improved submodels for use in a dynamic engine/vehicle model have been developed and the resulting code has been used to analyze the tip-in, tip-out behavior of a computer-controlled port fuel injected SI engine. This code consists of four submodels. The intake simulation submodel is similar to prior intake models, but some refinements have been made to the fuel flow model to more properly simulate a timed port injection system, and it is believed that these refinements may be of general interest. A general purpose engine simulation code has been used as a subroutine for the cycle simulation submodel. A conventional vehicle simulation submodel is also included in the model formulation. Perhaps most importantly, a submodel has been developed that explicitly simulates the response of the on-board computer (ECM) control system.
Technical Paper

A Fractal-Based SI Engine Model: Comparisons of Predictions with Experimental Data

1991-02-01
910079
A quasidimensional engine simulation which uses the concepts of fractal geometry to model the effects of turbulence on flame propagation in a homogeneous charge SI engine has been developed. Heat transfer and blowby/crevice flow submodels are included in this code and the submodels chosen are found to be reasonable. The model predictions of cylinder pressure histories are then compared with experimental data over a range of loads, equivalence ratios, and engine speeds. The model is not adjusted in any manner to yield better agreement with the data, other than by tuning the simple turbulence model used so as to yield agreement with data for the nonreacting flow. However, current information about the flame wrinkling scales in an engine is inadequate. Therefore, predictions are made for three different assumptions about the flame wrinkling scales which span the range of physically possible scales.
Technical Paper

Development of a Computationally Fast Equilibrium-Equivalent 4-Stroke SI Engine Model

1988-02-01
880130
A set of algebraic equations has been developed to replace the iterative thermochemical equilibrium subroutine in zero-dimensional and quasidimensional engine modeling codes. These equations allow calculation of the equilibrium composition given only the equivalence ratio and the fuel characteristics, thereby allowing the composition calculations to be performed external to the iterative main loop. This technique results in a decrease of the required computational time by up to a factor of 13, dependent upon the equivalence ratio and the fuel. The predictions of the equilibrium-equivalent code agree with those of a traditional equilibrium code within 2.5% for the four fuels examined (CH4, C3H8, C2H5OH, and i-C8H18) for compression ratios between 5 and 12:1, intake manifold pressures between 50 and 100 kPa, and equivalence ratios from 0.5 to 1.5. A technique for including constrained equilibrium to account for freezing of CO oxidation during the expansion stroke is also presented.
Technical Paper

Liquid Film Evaporation Off the Piston of a Direct Injection Gasoline Engine

2001-03-05
2001-01-1204
An optical access engine was used to image the liquid film evaporation off the piston of a simulated direct injected gasoline engine. A directional injector probe was used to inject liquid fuel (gasoline, i-octane and n-pentane) directly onto the piston of an engine primarily fueled on propane. The engine was run at idle conditions (750 RPM and closed throttle) and at the Ford World Wide Mapping Point (1500 RPM and 262 kPa BMEP). Mie scattering images show the liquid exiting the injector probe as a stream and directly impacting the piston top. Schlieren imaging was used to show the fuel vaporizing off the piston top late in the expansion stroke and during the exhaust stroke. Previous emissions tests showed that the presence of liquid fuel on in-cylinder surfaces increases engine-out hydrocarbon emissions.
Technical Paper

Particulate Characterization of a DISI Research Engine using a Nephelometer and In-Cylinder Visualization

2001-05-07
2001-01-1976
A nephelometer system was developed to characterize engine particulate emissions from DISI engines. Results were correlated with images showing the location and history of particulates in the cylinder of an optical engine. The nephelometer's operation is based upon the dependence of scattered laser light on particulate size from a flow sampled from the exhaust of an engine. The nephelometer simultaneously measured the scattered light from angles of 20° to 160° from the forward scattering direction in 4° increments. The angular scattering measurements were then compared with calculations using a Mie scattering code to infer information regarding particulate size. Measurements of particulate mass were made based upon a correlation developed between the scattered light intensity and particulate mass samples trapped in a 0.2-micron filter. Measurements were made in a direct injection single-cylinder spark ignition research engine having a transparent quartz cylinder.
Technical Paper

HEV Dynamometer Testing with State-of-Charge Corrections in the 1995 HEV Challenge

1996-02-01
960740
In the 1995 HEV Challenge competition, 17 prototype Hybrid Electric Vehicles (HEVs) were tested by using special HEV test procedures. The contribution of the batteries during the test, as measured by changes in battery state-of-charge (SOC), were accounted for by applying SOC corrections to the test data acquired from the results of the HEV test. The details of SOC corrections are described and two different HEV test methods are explained. The results of the HEV test methods are explained. The results of the HEV tests and the effects on the test outcome of varying HEV designs and control strategies are examined. Although many teams had technical problems with their vehicles, a few vehicles demonstrated high fuel economy and low emissions. One vehicle had emissions lower than California's ultra-low emission vehicle (ULEV) emissions rates, and two vehicles demonstrated higher fuel economy and better acceleration than their stock counterparts.
Technical Paper

Combustion Modeling in SI Engines with a Peninsula-Fractal Combustion Model

1996-02-01
960072
In premixed turbulent combustion models, two mechanisms have been used to explain the increase in the flame speed due to the turbulence. The newer explanation considers the full range of turbulence scales which wrinkle the flame front so as to increase the flame front area and, thus, the flame propagation speed. The fractal combustion model is an example of this concept. The older mechanism assumes that turbulence enables the penetration of unburned mixtures across the flame front via entrainment into the burned mixture zone. The entrainment combustion or eddy burning model is an example of this mechanism. The results of experimental studies of combustion regimes and the flame structures in SI engines has confirmed that most combustion takes place at the wrinkled flame front with additional combustion taking place in the form of flame fingers or peninsulas.
Technical Paper

Diluents and Lean Mixture Combustion Modeling for SI Engines with a Quasi-Dimensional Model

1995-10-01
952382
Lean mixture combustion might be an important feature in the next generation of SI engines, while diluents (internal and external EGR) have already played a key role in the reductions of emissions and fuel consumption. Lean burn modeling is even more important for engine modeling tools which are sometimes used for new engine development. The effect of flame strain on flame speed is believed to be significant, especially under lean mixture conditions. Current quasi-dimensional engine models usually do not include flame strain effects and tend to predict burn rate which is too high under lean burn conditions. An attempt was made to model flame strain effects in quasi-dimensional SI engine models. The Ford model GESIM (stands for General Engine SIMulation) was used as the platform. A new strain rate model was developed with the Lewis number effect included.
Technical Paper

The Texas Project: Part 2 - Control System Characteristics of Aftermarket CNG and LNG Conversions for Light-Duty Vehicles

1996-10-01
962099
The Texas Project involves the conversion of light-duty vehicles, up to and heavy light-duty trucks, to bi-fueled vehicles using commercially available aftermarket CNG and LPG conversion systems. The test fleet includes 68 dual fueled conversions. Virtually every type of aftermarket conversion technology for CNG and LPG was evaluated: eight different CNG and seven different LPG conversion “kits”, all of which are modern systems incorporating closed-loop control. The kits were installed and calibrated according to the manufacturer's guidelines and recommendations. The emissions when operating on the alternative fuel were compared to those when operating on certification gasoline to determine the “success” of the conversion. Many of these conversions, performed according to the manufacturer's requirements, were not “successful” (worse emissions than for gasoline operation). In almost all cases, the problem was NOx emissions that were too high when operating on the alternative fuel.
X