Refine Your Search

Topic

Author

Affiliation

Search Results

Standard

ELECTROMAGNETIC TESTING BY EDDY CURRENT METHODS

1991-03-01
HISTORICAL
J425_199103
The purpose of this SAE Information Report is to provide general information relative to the nature and use of eddy current techniques for nondestructive testing. The document is not intended to provide detailed technical information but to serve as an introduction to the principles and capabilities of eddy current testing, and as a guide to more extensive references listed in Section 2.
Collection

Multi-Dimensional Engine Modeling, 2018

2018-04-03
This collection covers advances in the development and application of models and tools involved in multi-dimensional engine modeling: advances in chemical kinetics, combustion and spray modeling, turbulence, heat transfer, mesh generation, and approaches targeting improved computational efficiency. Papers employing multi-dimensional modeling to gain a deeper understanding of processes related to turbulent transport, transient phenomena, and chemically reacting, two-phase flows are included in this collection.
Standard

Fuel Injection Equipment Nomenclature

1999-04-21
HISTORICAL
J830_199904
This SAE Standard establishes a vocabulary and definitions relating to the components used in fuel injection systems for compression ignition (diesel) engines. Definitions are separated into six sections by topic as follows: Section 3— Fuel Injection Pumps Section 4— Fuel Injectors Section 5— Unit Injectors Section 6— Governors Section 7— Timing Devices Section 8— High Pressure Pipes and Connections NOTE— When the word "fuel" is used in the terms listed it may be omitted providing there can be no misunderstanding.
Standard

Split Type Bushings – Design and Application

2011-06-13
CURRENT
J835_201106
This SAE Standard presents the standard sizes, important dimensions, specialized measurement techniques, and tolerances for split type bushings. Both SI and inch sizes are shown; their dimensions are not exact equivalents. New designs shall use SI units. Unless specifically stated as ±, all tolerances are total.
Standard

Socket Wrenches, Hand (Metric)

2013-02-10
CURRENT
MA4534A
This SAE Aerospace Standard covers high strength commercial sockets and universal sockets which possess the strength, clearances, and internal wrenching design so configured that, when mated with hexagon (6 point) fasteners, they shall transmit torque to the fastener without bearing on the outer 5% of the fastener’s wrenching points. This document provides additional requirements beyond ANSI B107.5 appropriate for aerospace use. Inclusion of dimensional data in this document is not intended to imply all of the products described therein are stock production sizes. Consumers are requested to consult with manufacturers concerning lists of stock production sizes.
Standard

Sleeve Type Half Bearings

2011-06-10
CURRENT
J506_201106
This SAE Standard defines the normal dimensions, dimensioning practice, tolerances, specialized measurement techniques, and glossary of terms for bearing inserts commonly used in reciprocating machinery. The standard sizes cover a range which permits a designer to employ, in proper proportion, the durability and lubrication requirements of each application, while utilizing the forming and machining practices common in manufacture of sleeve type half bearings. Not included are considerations of hydrodynamic lubrication analysis or mechanical stress factors of associated machine structural parts which determine the nominal sizes to be used, selection of bearing material as related to load carrying capacity, and economics of manufacture. For information concerning materials, see SAE J459 and SAE J460. These suggested sizes provide guidelines which may result in minimal costs of tooling but do not necessarily represent items which can be ordered from stock.
Standard

Diesel Engines - Steel Tubes for High-Pressure Fuel Injection Pipes (Tubing)

2015-11-24
CURRENT
J1958_201511
This SAE Standard specifies dimensions and requirements for single-wall steel tubing intended for use as high-pressure fuel injection pipes on a wide range of engines (Class A), and for fuel injection pump testing (Class B, Reference SAE J1418). Tubing shall be cold drawn, annealed or normalized, seamless tubing suitable for cold swaging, cold upsetting, and cold bending.
Standard

Diesel Engines--Steel Tubes for High-Pressure Fuel Injection Pipes (Tubing)

1995-06-01
HISTORICAL
J1958_199506
This SAE Standard specifies dimensions and requirements for single-wall steel tubing intended for use as high-pressure fuel injection pipes on a wide range of engines (Class A), and for fuel injection pump testing (Class B, Reference SAE J1418). Tubing shall be cold drawn, annealed or normalized, seamless tubing suitable for cold swaging, cold upsetting and cold bending.
Standard

Diesel Engines—Steel Tubes for High-Pressure Fuel Injection Pipes (Tubing)

2002-10-25
HISTORICAL
J1958_200210
This SAE Standard specifies dimensions and requirements for single-wall steel tubing intended for use as high-pressure fuel injection pipes on a wide range of engines (Class A), and for fuel injection pump testing (Class B, Reference SAE J1418). Tubing shall be cold drawn, annealed or normalized, seamless tubing suitable for cold swaging, cold upsetting, and cold bending.
Standard

Diesel Engines--Steel Tubes for High-Pressure Fuel Injection Pipes (Tubing)

1989-04-01
HISTORICAL
J1958_198904
This SAE Standard specifies dimensions and requirements for single-wall steel tubing intended for use as high-pressure fuel injection pipes on a wide range of engines (Class A), and for fuel injection pump testing (Class B, Reference SAE J1418). Tubing shall be cold drawn, annealed or normalized, seamless tubing suitable for cold swaging, cold upsetting, and cold bending.
Standard

TOOL AND DIE STEELS

1970-05-01
HISTORICAL
J438_197005
This standard covers the identification, classification, and chemical composition of tool and die steels for use by engineers, metallurgists, tool designers, tool room supervisors, heat treaters, and tool makers.
Standard

Tool and Die Steels

2018-01-09
CURRENT
J438_201801
This standard covers the identification, classification, and chemical composition of tool and die steels for use by engineers, metallurgists, tool designers, tool room supervisors, heat treaters, and tool makers.
Standard

ELECTROPLATING AND RELATED FINISHES

1985-02-01
CURRENT
J474_198502
Electroplating is a process whereby an object is coated with one or more relatively thin, tightly adherent layers of one or more metals. It is accomplished by placing the object to be coated on a plating rack or a fixture, or in a basket or in a rotating container in such a manner that a suitable current may flow through it, and then immersing it in a series of solutions and rinses in planned sequence. The advantage to be gained by electroplating may be considerable; broadly speaking, the process is used when it is desired to endow the basis material (selected for cost, material conservation, and physical property reasons) with surface properties it does not possess. It should be noted that although electroplating is the most widely used process for applying metals to a substrate, they may also be applied by spraying, vacuum deposition, cladding, hot dipping, chemical reduction, mechanical plating, etc.
Standard

WROUGHT NICKEL AND NICKEL-RELATED ALLOYS

1976-07-01
HISTORICAL
J470_197607
This Report presents general information on over 50 alloys in which nickel either predominates or is a significant alloying element. It covers primarily wrought materials, and is not necessarily all inclusive. Values given are in most cases average or nominal, and if more precise values are required the producer(s) should be contacted. This report does not cover the so-called "superalloys," or the iron base stainless steels. Refer to SAE J467, Special Purpose Alloys, and SAE J405, Chemical Compositions of SAE Wrought Stainless Steels, respectively, for data on these alloys.
Standard

Wrought Nickel and Nickel-Related Alloys

2018-02-15
CURRENT
J470_201802
This Report presents general information on over 50 alloys in which nickel either predominates or is a significant alloying element. It covers primarily wrought materials, and is not necessarily all inclusive. Values given are in most cases average or nominal, and if more precise values are required the producer(s) should be contacted. This report does not cover the so-called "superalloys," or the iron base stainless steels. Refer to SAE J467, Special Purpose Alloys, and SAE J405, Chemical Compositions of SAE Wrought Stainless Steels, respectively, for data on these alloys.
X