Refine Your Search

Topic

Author

Affiliation

Search Results

Collection

Vehicle Dynamics, Stability and Control, 2017

2017-03-28
This technical paper collection is focused on vehicle dynamics and controls using modeling and simulation, and experimental analysis of passenger cars, heavy trucks, and wheeled military vehicles. The papers address active and passive safety systems to mitigate rollover, yaw instability and braking issues; driving simulators and hardware-in-the-loop systems; suspension kinematics and compliance, steering dynamics, advanced active suspension technologies; and tire force and moment mechanics.
Standard

In-line, Elbow, and Tee Flanged Connectors for use with SAE J518-1/ISO6162-1 Components

2015-02-03
WIP
J518/4
This document standardizes the design of connector blocks used for joining SAE J518-1/ISO 6162-1 (Code 61) flange heads with other SAE J518-1/ISO 6162-1 (Code 61) flange heads with straight, elbow, and tee geometries. The blocks specified in this document are designed to provide for very compact installations. As a result, the tap depths specified in this document do not conform to those specified in SAE J518-1/ISO 6162-1 to allow for a minimal bend radius in the elbow and tee configurations. This document specifies both inch and metric configurations
Standard

Round Head Bolts

1990-01-01
CURRENT
J481_199001
Round head bolts are made in two body styles: (a) A full size body, with a maximum diameter somewhat greater than the nominal diameter (not an SAE Standard except for ribbed neck bolts, Table 3); and (b) an undersize body, with a minimum diameter approximating the pitch diameter of the thread and a maximum diameter never exceeding nominal (SAE standard for all types except ribbed neck bolts). The body diameter of either style may be exceeded by a reasonable swelling or fin under the head, or under corners of the square necks, to the extent that serviceability is not affected.
Standard

Cotter Pins

1990-01-01
CURRENT
J487_199001
Not available.
Standard

Alignment of Nut Slots

1990-01-01
CURRENT
J484_199001
This method of gaging alignment of nut slots allows equal variations for location of the cotter pin hole in the bolt and location of slots in the nut. To inspect the nut, the slotted gage is inserted through the nut hole from the bearing surface of the nut. Alignment of slots is considered satisfactory if the gage pin can be slipped into the gage and nut slots without interference.
Standard

Brake Rotor Thickness Variation and Lateral Run-Out Measurements

2015-10-02
WIP
J3111
The scope of this recommended practice is to establish definitions and recommended methods for the measurement of lateral run-out and disc thickness variation in the laboratory and vehicle for passenger cars and light duty trucks up to 4546 kg gross vehicle weight. This recommended practice will breakdown the instrumentation (sensors and sizes), test setup, and data processing.
Standard

Coiled Tubing Assemblies for Heavy Duty Air Brake Applications

2013-04-30
WIP
J3041
This SAE Standard establishes the minimum performance and endurance requirements for coiled air brake tubing assemblies used for hookup between tractors, trailers and converter dollies. The Standards SAE J844 and SAE J246 along with J1131 must be consulted to determine the complete performance and endurance requirements of individual components of the system. Related TMC Recommended Practices may be consulted for information associated with selection, installation and inspection of these assemblies. This document is intended to set out requirements for the majority of conditions rather than for specialized applications or environments.
Standard

Performance Requirements for Nonmetallic Air Brake System Tubing

2014-08-26
WIP
J2547
This SAE Standard covers the minimum requirements for nonmetallic tubing as manufactured for use in air brake systems which tubing is different from that described in SAE J844. It is not intended to cover tubing for any portion of the system which operates continuously below - 40 degrees C or above +93 degrees C, above a maximum working gage pressure of 1.0 MPa, or in an area subject to attack by battery acid. This tubing is intended for use in the brake system for connections, which maintain a basically fixed relationship between components during vehicle operation. Coiled tube assemblies required for those installations where flexing occurs are covered by this document, SAE J1131 and SAE J2494-3, to the extent of setting minimum requirements on the essentially straight tube and tube fitting connections which are used in the construction of such assemblies.
Standard

Validation of Compressibility Test Systems for Friction Materials

2016-02-17
WIP
J3079/1
This SAE Recommended Practice applies to the validation process required for test systems used to measure deflection or compressibility of friction materials and friction material assemblies for passenger cars, light trucks, and commercial vehicles equipped with hydraulic or air brake systems, and using disc or drum brakes.
Standard

Balance Weight and Rim Flange Design Specifications, Test Procedures, and Performance Recommendations for Heavy Vehicle Applications

2018-04-12
WIP
J3172
This SAE Recommended Practice is intended to serve as a guide for standardization of features, dimensions, and configurations of balance weights for aluminum and steel wheels intended for use on Heavy Truck/Vehicles (Class 5-8) to assure good installation and retention of the balance weight. This document also provides test procedures and minimum performance requirements for testing balance weight retention.
Standard

Concepts, Terms and Definitions Related to Surrogate Measures of Safety

2018-01-12
WIP
J3166
The document will define and describe in condensed form the fundamental theoretical concepts of surrogate measures of safety and define indicators (with variations). To the extent possible, the definitions should be kept neutral with respect to the technology or data collection method used as these change rapidly.
Standard

Component Level EPB Actuation NVH

2018-01-10
WIP
J3165
The component level EPB actuation NVH task force should review existing specifications and measurement methods used in the industry to find any commonalities and propose a recommended method for measuring and evaluating component level EPB actuation NVH to be used as a common standard throughout the industry. The task force should acknowledge the following objectives: 1. Task force should review existing industry specifications and further define the scope for creating the new standalone component level EPB actuation NVH standard a. The common standard should be universally recognized and accepted by the automotive industry b. Provide confidence that acceptable vehicle related NVH results will be achieved if vehicle level testing is completed c. Provide clear verifiable acceptance criteria 2. Task force must lay out steps and timing to complete the development of the new common standard. 3.
Standard

Electric Park Brake Sizing

2017-10-16
WIP
J3158
The scope of this new recommended practice should include, but not necessarily be limited to: 1. Define vehicle operating conditions used to drive MOC-EPB actuator design and selection 2. Define brake corner operating conditions (e.g. temperature and state of burnish) used to drive MOC-EPB actuator design and selection 3. Define actuator operating conditions (e.g. temperature, voltage, current limit, and state of wear) used to drive MOC-EPB actuator design and selection 4. Define methodology for addressing part to part variation in performance
Standard

Dynamometer Low-Frequency Brake Noise Test Procedure

2017-07-18
WIP
J3002
This procedure will outline the necessary test equipment (fixturing, dynamometer, data acquisition system, etc.) and test sequence required to test for low-frequency brake noise on a brake noise dynamometer. It is intended to complement SAEJ2521, which focuses on high-frequency brake squeal.
X