Refine Your Search

Topic

Author

Affiliation

Search Results

Standard

Wheel Mounting Elements for Industrial and Agricultural Disc Wheels

1986-06-01
HISTORICAL
J714_198606
This SAE Recommended Practice includes wheel mounting elements subject to standardization in a series of industrial and agricultural disc wheels. The disc may be reversible or nonreversible and concave or convex (See Figure 1 and Table 1).
Standard

Engine and Transmission Dipstick Marking

1977-08-01
HISTORICAL
J614_197708
This SAE Recommended Practice provides information useful in the marking of engine and transmission dipsticks used for fluid level indication.
Standard

Companion Flanges, Type A (External Pilot) and Type S (Internal Pilot)

1991-01-31
HISTORICAL
J1946_199101
This SAE Standard specifies the nominal dimensions and tolerances which affect the interchangeability between companion flanges and mating parts. The flanges covered by this document are designated type A and type S. The type A flanges are equivalent to type A ISO 7646. The type S flanges are equivalent to the type S ISO 7647. Type A is an external (male) pilot construction and type S is an internal (female) pilot construction. These flanges are not interchangeable. Dimensions not specified are left to the discretion of the component manufacturer.
Standard

Connections for On-Board Road Vehicle Electrical Wiring Harnesses--Part 2: Tests and General Performance Requirements

2005-02-02
HISTORICAL
J2223/2_200502
This SAE Standard defines tests methods and general performance requirements of single-pole and multiple connectors for on-board electrical wiring harnesses of road vehicles. These requirements are not intended for connections internal to electronic devices. This document applies to connectors designed to be disconnected after mounting in the vehicle in the case of repair and/or maintenance.
Standard

Cartridge Cavity

2018-10-30
CURRENT
J2494/4_201810
This SAE Standard covers complete general and dimensional data for the manufacture of, T6061-T6 Aluminum cavities designed to receive Push To Connect threadless fittings known as “cartridges“, for air brake applications. This document is not intended to specify or recommend any style or manufacture of such cartridges but to establish uniform cavity dimensions for interchangeability purposes.
Standard

Cartridge Cavity

2011-10-28
HISTORICAL
J2494/4_201110
This SAE Standard covers complete general and dimensional data for the manufacture of, T6061-T6 Aluminum cavities designed to receive Push To Connect threadless fittings known as “cartridges“, for air brake applications. This document is not intended to specify or recommend any style or manufacture of such cartridges but to establish uniform cavity dimensions for interchangeability purposes.
Video

SAE Eye on Engineering: Conti's Smart Backup Camera

2018-11-08
Every year in the U.S., about 300 people die, and 15 thousand vehicles suffer accidents, while backing up. In this episode of SAE Eye on Engineering, Editor-in-Chief Lindsay Brooke looks at Continental's new intelligent backup camera that's small in size but huge in capability. SAE Eye on Engineering also airs Monday mornings on WJR 760 AM Detroit's Paul W. Smith Show.
Standard

Standard Rainflow File Format

2018-08-24
CURRENT
J2623_201808
This SAE Standard provides a definition of a rainflow file format. This type of simple text file would contain all relevant information about the rainflow cycle content of a time history. Included information are Comments, Signal Range, Signal Mean, Number of Cycles, Signal Maximum, Signal Minimum. Rainflow cycle counting has become the most accepted procedure for identifying material fatigue relevant cycles in complex variable amplitude load time histories. The cycle counting methods account for the effects of material plasticity and material memory of prior deformation, and the resulting compressed history information is used by durability analysts to estimate the effects of a given service or test history.
Standard

15 Pole Connector Between Towing Vehicles and Trailers with 12 Volt Nominal Supply

2013-04-09
HISTORICAL
J2691_201304
This SAE standard establishes the minimum construction and performance requirements for a 15 Pole Connector Between Towing Vehicles and Trailers, for trucks, trailers, and dollies in conjunction with SAE J2742 “Combination 11 Conductors and 4 Pairs ECBS Cable”. The connector accommodates both power and ISO 11992-1 signal circuits along with dual ground wires to accommodate grounding requirements within the constraints of the SAE J2691 terminal capacity.
Standard

15 Pole Connector Between Towing Vehicles and Trailers with 12 Volt Nominal Supply

2018-04-15
CURRENT
J2691_201804
This SAE standard establishes the minimum construction and performance requirements for a 15 Pole Connector Between Towing Vehicles and Trailers, for trucks, trailers, and dollies in conjunction with SAE J2742. The connector accommodates both power and ISO 11992-1 signal circuits along with dual ground wires to accommodate grounding requirements within the constraints of the SAE J2691 terminal capacity.
Standard

Steel Self-Drilling Tapping Screws

2014-09-09
WIP
J78
This SAE Standard covers the dimensional and general specifications, including performance requirements, for carbon steel self-drilling tapping screws suitable for use in general applications. It is the objective of this document to insure that carbon steel self-drilling tapping screws, by meeting the mechanical and performance requirements specified, shall drill a hole and form or cut mating threads in materials into which they are driven without deforming their own thread and without breaking during assembly. Appendix A is included to provide a recommended technique for measuring the case depth on the screws.
Standard

Steel Self-Drilling Tapping Screws

2013-04-16
CURRENT
J78_201304
This SAE Standard covers the dimensional and general specifications, including performance requirements, for carbon steel self-drilling tapping screws suitable for use in general applications. It is the objective of this document to insure that carbon steel self-drilling tapping screws, by meeting the mechanical and performance requirements specified, shall drill a hole and form or cut mating threads in materials into which they are driven without deforming their own thread and without breaking during assembly. Appendix A is included to provide a recommended technique for measuring the case depth on the screws.
Video

SAE Eye on Engineering: Conti's Virtual A-Pillar tech

2018-11-13
The pillars that frame both sides of your car's windshield are known as the A pillars. In this episode of SAE Eye on Engineering, Editor-in-Chief Lindsay Brooke looks at Continental's new "Virtual" A pillar. SAE Eye on Engineering also airs Monday mornings on WJR 760 AM Detroit's Paul W. Smith Show.
Standard

High and Low Crown (Blind, Acorn) Hex Nuts

2016-11-18
CURRENT
J483_201611
Included in this SAE Recommended Practice are complete general and dimensional data for the high and low types of crown nuts recognized as SAE Standard. These nuts are primarily intended for application in automotive and other ground-based motor vehicles and industrial equipment to provide an ornamental or protective closure over end of bolts, studs, or screws.
Standard

High and Low Crown (Blind, Acorn) Hex Nuts

2013-04-15
HISTORICAL
J483_201304
Included in this SAE Recommended Practice are complete general and dimensional data for the high and low types of crown nuts recognized as SAE Standard. These nuts are primarily intended for application in automotive and other ground-based motor vehicles and industrial equipment to provide an ornamental or protective closure over end of bolts, studs, or screws.
X