Refine Your Search

Topic

Author

Affiliation

Search Results

Standard

In-line, Elbow, and Tee Flanged Connectors for use with SAE J518-1/ISO6162-1 Components

2015-02-03
WIP
J518/4
This document standardizes the design of connector blocks used for joining SAE J518-1/ISO 6162-1 (Code 61) flange heads with other SAE J518-1/ISO 6162-1 (Code 61) flange heads with straight, elbow, and tee geometries. The blocks specified in this document are designed to provide for very compact installations. As a result, the tap depths specified in this document do not conform to those specified in SAE J518-1/ISO 6162-1 to allow for a minimal bend radius in the elbow and tee configurations. This document specifies both inch and metric configurations
Standard

Round Head Bolts

1990-01-01
CURRENT
J481_199001
Round head bolts are made in two body styles: (a) A full size body, with a maximum diameter somewhat greater than the nominal diameter (not an SAE Standard except for ribbed neck bolts, Table 3); and (b) an undersize body, with a minimum diameter approximating the pitch diameter of the thread and a maximum diameter never exceeding nominal (SAE standard for all types except ribbed neck bolts). The body diameter of either style may be exceeded by a reasonable swelling or fin under the head, or under corners of the square necks, to the extent that serviceability is not affected.
Standard

Cotter Pins

1990-01-01
CURRENT
J487_199001
Not available.
Standard

Alignment of Nut Slots

1990-01-01
CURRENT
J484_199001
This method of gaging alignment of nut slots allows equal variations for location of the cotter pin hole in the bolt and location of slots in the nut. To inspect the nut, the slotted gage is inserted through the nut hole from the bearing surface of the nut. Alignment of slots is considered satisfactory if the gage pin can be slipped into the gage and nut slots without interference.
Standard

Committee Charter

2014-04-09
WIP
MTL-14-AA
SAE Metallic Materials Testing Laboratories, is a technical Subcommittee in SAE’s Aerospace Materials Systems Group with the responsibility to develop and maintain material specifications and other SAE technical reports for Aerospace Metallic Materials Testing Requirements. The Subcommittee works in conjunction with related bodies such as the Performance Review Institute (PRI), and regulatory authorities such as FAA and EASA. The objectives of MTL are to: • Develop Aerospace Specifications (AS) for the control of materials testing specific to aerospace applications. • Provide a forum for the exchange of technical information related to aerospace materials testing. • Further the adaptation of industry sponsored material specifications through coordination with PRI and associated organizations. • Establish a system to ensure aerospace specifications are controlled.
Standard

Thermoplastic Coolant Tubes

2018-09-11
WIP
J3181
Standard covers material performance requirements for extruded thermoplastic tubes used in engine coolant/water applications.
Standard

Nonmetallic EGR Tubing with One or More Layers

2018-09-11
WIP
J3183
This SAE Standard presents the minimum requirements for nonmetallic tubing with one or more layers manufactured for use in exhaust gas recirculation systems Requirements in this document apply to monowall tubing (one layer construction) and multilayer tubing. The tube construction can have a straight wall configuration, a wall that is convoluted or corrugated, or a combination of each.
Standard

Diesel Exhaust Fluid (DEF) tubing with one or more layers

2018-09-11
WIP
J3184
This SAE Standard presents the minimum requirements for nonmetallic tubing with one or more layers manufactured for use as liquid carrying DEF lines for diesel engine selective catalyst reduction (SCR) after-treatment systems. Requirements in this document also apply to monowall tubing (one layer construction) and multi-layer constructions. Unless otherwise agreed to by suppliers and users this document applies to tubing for any portion of the DEF system that might operate continuously at temperatures above –40 °C and below 120 °C or for high temperature systems up to 160 °C. Maximum working pressure of 1140 kPa absolute. The tubing can be used at the peak intermittent exterior temperature up to 140 °C or 180 °C. Tubing systems supplied to this application are usually required to thaw from the frozen condition using various heating methods in operation complying with EPA requirements.
Standard

Nonmetallic Air Suspension System Tubing with One or More Layers

2018-09-11
WIP
J3185
This SAE Standard presents the minimum requirements for nonmetallic tubing with one or more layers manufactured for use as pneumatic tubing in automotive air suspension lines. Requirements in this document also apply to monowall tubing (one layer construction) or multi-layer (MLT) constructions. Unless otherwise agreed to by suppliers and users this document applies to tubing for any portion of the fuel system that might operate continuously at temperatures above –40°C and below 90°C and up to a maximum working gage pressure of 1500 kPa. The tubing can be used at the peak intermittent temperature up to 115 °C with peak dynamic pressures of up to 2000 kPa. This document can apply to systems that operate at higher pressures and/or are exposed to higher temperatures with appropriate changes to the acceptance criteria within this document.
Book

Composite Materials: Advanced Materials and Lightweighting (DVD)

2015-04-15
technology breakthroughs. Viewers are virtually taken to labs and research centers to learn how design engineers are enhancing product performance/reliability, reducing cost, improving quality, safety or environmental impact, and achieving regulatory compliance. In the episode "Composite Materials: Advanced Materials and Lightweighting" (30:20), Molded Fiber Glass Companies, known for its deep involvement in the creative development of the molded fiberglass process for the Corvette, demonstrates the manufacturing of sheet molded composite for fiberglass parts. Tanom Motors introduces the Tanom Invader , a blend between an automobile and a motorcycle made exclusively with composite materials. Finally, Euro-Composites demonstrates the manufacturing of honeycomb core material made out of aramid paper and phenolic resin used in aircraft structures.
Collection

Fuel and Additive Effects on Engine Systems, 2017

2017-03-28
Topics include the effects of fuel and additives on deposit formation, intake system cleanliness, friction, wear, corrosion, and elastomer compatibility. Also covered are effects of fuel specification on drivability, on evaporative emissions, and on the relationship between emissions and drive cycle.
Collection

Fatigue Modeling/Testing & CAE Durability Analysis, 2017

2017-03-28
This collection of papers focus on state-of-the-art fatigue theory and advanced development in fatigue testing, material behavior under cyclic loading, and fatigue analysis methodology & research in the ground vehicle industry. Studies and discussions on innovative and improved fatigue theory/methods in will be discussed along with and engineering applications of CAE durability analysis.
Video

BMW Technology/Strategy Regarding EV

2011-11-04
The BMW Group has introduced electric cars to the market with the MINI E already in 2009. The next step will be the launch of the BMW ActiveE in 2011, followed by the revolutionary Mega City Vehicle in 2013. The presentation will explain the BMW Group strategy for implementing sustainable mobility. A focus will be emobility, the use of carbon fiber and the holistic sustainability approach of BMW Group?s project i. Reference will be made to the research results of the MINI E projects in the US and in Europe. Presenter Andreas Klugescheid, BMW AG
Video

Transesterification of Waste Cooking Oil in Presence of Crushed Seashell as a Support for Solid Heterogeneous Catalyst

2011-12-05
Developing relatively cheap and widely available resources for heterogeneous solid catalyst synthesis is a promising approach for biodiesel fuel industry. Seashell which is essentially calcium carbonate can be used as a basic support for transesterification heterogeneous catalysts. In the present investigation, the alcoholysis of waste frying oil has been carried out using seashell-supported K3 PO4 as solid catalyst. Presenter Essam Oun Al-Zaini, PhD student, UNSW
Video

Monitoring NO2 Production of a Diesel Oxidation Catalyst

2012-01-24
A combination of laboratory reactor measurements and vehicle FTP testing has been combined to demonstrate a method for diagnosing the formation of NO2 from a diesel oxidation catalyst (DOC). Using small cores from a production DOC and simulated diesel exhaust, the laboratory reactor experiments are used to support a model for DOC chemical reaction kinetics. The model we propose shows that the ability to produce NO2 is chemically linked to the ability of the catalyst to oxidize hydrocarbon (HC). For thermally damaged DOCs, loss of the HC oxidation function is simultaneous with loss of the NO2 production function. Since HC oxidation is the source of heat generated in the DOC under regeneration conditions, we conclude that a diagnostic of the DOC exotherm is able to detect the failure of the DOC to produce NO2. Vehicle emissions data from a 6.6 L Duramax HD pick-up with DOC of various levels of thermal degradation is provided to support the diagnostic concept.
X