Standard
AS882 Pin - Trim Control
1941-06-02
CURRENT
AS882-2
No scope available.
Search Results
Software
SAE J2008 - Recommended Organization of Vehicle Service Information for Interchange on CD-ROM
1998-12-30
SAE J2008 Recommended Organization of Vehicle Service Information for Interchange Access to accurate service information is critical for the diagnosis and repair of increasingly complex vehicle systems. Though aftermarket technicians perform a significant amount of this service and repair, they do not have fast, easy access to this important information. If proper procedures are not readily available, the technician may use a less effective technique that could directly impact the vehicle's performance. The goal of SAE J2008 is to enable manufacturers to standardize vehicle service information in order to increase technician familiarity and reduce search time with easy data retrieval. SAE J2008 on CD-ROM brings you the information you need to standardize your vehicle service informationtoday.
Standard
Steel Tubing (Seamless for Machined Parts) 1.8ni 0.80cr 0.25mo (0.38 - 0.43c) Heat Treated (200,000 Tensile Strength)
2002-12-16
CURRENT
AMS6420
Standard
Steel Tubing (Seamless for Machined Parts) .55ni .25mo (.33 - .38c) Normalized Or Heat-Treated (90,000 Tensile Strength)
2002-12-16
CURRENT
AMS6283
Standard
Steel Tubing (Seamless for Machined Parts) .55ni .50cr .25mo (.35 - .38c) Heat-Treated (125,000 Tensile Strength)
2002-12-16
CURRENT
AMS6284
Standard
Steel Tubing (Seamless for Machined Parts) .55ni .50cr .25mo (.38 - .43c) Heat-Treated (180,000 Tensile Strength)
2002-12-16
CURRENT
AMS6285
Standard
Steel Tubing (Seamless for Machined Parts) .55ni .50cr .25mo (.38-.43c) Heat-Treated (180,000 T.S.)
2002-12-16
CURRENT
AMS6286
Standard
NUTS, SELF-LOCKING, STEEL High Strength, Prevailing-Torque, All Metal 450 F (232 C) Use, Unified "J" (MIL-S-8879) Thread Form
1969-11-01
HISTORICAL
AMS7252
Standard
NUTS, SELF-LOCKING, STEEL High Strength, All Metal 450° F (230° C) Use, Unified "J" (MIL-S-8879) Thread Form
1980-01-15
HISTORICAL
AMS7252B
This specification covers all-metal, self-locking nuts, plate nuts, and gang channel nuts made of a carbon or low-alloy steel.
Standard
NUTS, SELF-LOCKING, STEEL High Strength, Prevailing Torque, All Metal 450° F (232° C) Use, Unified "J" (MIL-S-8879) Thread Form
1973-05-15
HISTORICAL
AMS7252A
This specification covers all-metal, self-locking, prevailing-torque nuts, plate nuts, and gang channel nuts made of a carbon or low-alloy steel.
Standard
BOLTS AND SCREWS, TITANIUM ALLOY 6Al - 4V Upset Headed, Heat Treated, Roll Threaded
1973-05-15
HISTORICAL
AMS7461B
This specification covers premium quality bolts and screws made of 6Al - 4V titanium alloy.
Standard
BOLTS AND SCREWS, TITANIUM ALLOY 6Al - 4V Upset Headed, Heat Treated, Roll Threaded
1970-11-01
HISTORICAL
AMS7461A
Standard
BOLTS AND SCREWS, TITANIUM ALLOY 6Al - 4V Upset Headed, Heat Treated, Roll Threaded
1964-06-30
HISTORICAL
AMS7461
Standard
Alignment of Nut Slots
1990-01-01
CURRENT
J484_199001
This method of gaging alignment of nut slots allows equal variations for location of the cotter pin hole in the bolt and location of slots in the nut. To inspect the nut, the slotted gage is inserted through the nut hole from the bearing surface of the nut. Alignment of slots is considered satisfactory if the gage pin can be slipped into the gage and nut slots without interference.
Standard
Round Head Bolts
1990-01-01
CURRENT
J481_199001
Round head bolts are made in two body styles: (a) A full size body, with a maximum diameter somewhat greater than the nominal diameter (not an SAE Standard except for ribbed neck bolts, Table 3); and (b) an undersize body, with a minimum diameter approximating the pitch diameter of the thread and a maximum diameter never exceeding nominal (SAE standard for all types except ribbed neck bolts). The body diameter of either style may be exceeded by a reasonable swelling or fin under the head, or under corners of the square necks, to the extent that serviceability is not affected.
Standard
CABIN CONNECTORS AND CABLES PART 2 SPECIFICATION OF CONNECTORS, CONTACTS, AND BACKSHELLS
2018-11-28
CURRENT
ARINC800P2-1
This specification describes the general connectors, contacts, and backshells in their shape and characteristic for cabin systems for commercial aircrafts. ARINC 600, ARINC 404, and ARINC 801 connector specifications are published as independent standards.
Standard
CABIN CONNECTORS AND CABLES PART 2 SPECIFICATION OF CONNECTORS, CONTACTS, AND BACKSHELLS
2021-09-09
CURRENT
ARINC800P2-2
This specification describes the general connectors, contacts, and backshells in their shape and characteristic for cabin systems for commercial aircrafts. ARINC 600, ARINC 404, and ARINC 801 connector specifications are published as independent standards.
Standard
AS29600-699 Bolt, Externally Relieved Body - Dee Head DTD5077, 10(.190)-32UNJF - 3A BS4084
1972-01-12
CURRENT
AS29600-2
No scope available.
Standard
CABIN CONNECTORS AND CABLES, PART 4, STANDARD TEST METHODOLOGY
2020-07-13
CURRENT
ARINC800P4-1
ARINC 800 is the first industry standard intended for characterization of aviation-grade high-speed (Gbps) Ethernet links. The test methods are based on realistic representation of cabin networks. The notional cabling architecture is based on IFE seat distribution using multiple intermediate disconnects. Sequential testing is supported by building up number of connectors in the link. Test guidelines for mixed intermediate cable lengths are provided.
Standard
EMBEDDED INTERCHANGE FORMAT FOR TERRAIN DATABASES
2018-12-21
CURRENT
ARINC813
This document defines an open encoding format for terrain databases. This format, when designed and implemented, will enable a quick, economic, and efficient use of Terrain Databases (TerrDBs). However, since industry does not require applications to be standardized, data interpretation is not addressed in this document.
