Refine Your Search

Topic

Author

Affiliation

Search Results

Standard

In-line, Elbow, and Tee Flanged Connectors for use with SAE J518-1/ISO6162-1 Components

2015-02-03
WIP
J518/4
This document standardizes the design of connector blocks used for joining SAE J518-1/ISO 6162-1 (Code 61) flange heads with other SAE J518-1/ISO 6162-1 (Code 61) flange heads with straight, elbow, and tee geometries. The blocks specified in this document are designed to provide for very compact installations. As a result, the tap depths specified in this document do not conform to those specified in SAE J518-1/ISO 6162-1 to allow for a minimal bend radius in the elbow and tee configurations. This document specifies both inch and metric configurations
Standard

Round Head Bolts

1990-01-01
CURRENT
J481_199001
Round head bolts are made in two body styles: (a) A full size body, with a maximum diameter somewhat greater than the nominal diameter (not an SAE Standard except for ribbed neck bolts, Table 3); and (b) an undersize body, with a minimum diameter approximating the pitch diameter of the thread and a maximum diameter never exceeding nominal (SAE standard for all types except ribbed neck bolts). The body diameter of either style may be exceeded by a reasonable swelling or fin under the head, or under corners of the square necks, to the extent that serviceability is not affected.
Standard

Cotter Pins

1990-01-01
CURRENT
J487_199001
Not available.
Standard

Alignment of Nut Slots

1990-01-01
CURRENT
J484_199001
This method of gaging alignment of nut slots allows equal variations for location of the cotter pin hole in the bolt and location of slots in the nut. To inspect the nut, the slotted gage is inserted through the nut hole from the bearing surface of the nut. Alignment of slots is considered satisfactory if the gage pin can be slipped into the gage and nut slots without interference.
Standard

Ambient Temperature Fixed Orifice Fueling

2016-11-21
WIP
J2601/4
SAE J#### establishes the protocol and process limits for hydrogen fueling of light duty vehicles when the fuel delivery temperature is not pre-cooled, so called “ambient fueling” designated by Table 1 of SAE J2601-2014. These process limits (including the fuel delivery temperature, the maximum fuel flow rate, the rate of pressure increase and the ending pressure) are affected by factors such as ambient temperature, fuel delivery temperature and initial pressure in the vehicle’s compressed hydrogen storage system. SAE J#### establishes standard fueling protocols based on a series of design cases representing fueling system engineering categories. These categories are intended to provide performance targets which allow decreasing fueling times relative to the most simple design case. Similar to the table and formula based approaches of SAE J2601-2014, this approach establishes a minimum performance criteria leaving open options for innovation to decrease fueling times.
Standard

Application Guideline for Use of Hydrogen Quality Specification

2014-04-15
WIP
J2719/1
The purpose of this TIR is to provide guidance for minimizing test requirements based on SAE J2719 while still ensuring fuel quality at hydrogen fueling stations for PEM fuel cell vehicles (FCVs) and ICEVs (to the extent that has been determined). This document is intended to be used by both industry and regulators for routine (or periodic) monitoring of filling station performance.
Standard

Techniques for measuring the properties of lithium and lithium-ion battery anode active materials.

2017-10-18
WIP
J3159
This SAE RP provides a set of test methods and practices for the characterization of the properties of lithium battery anode active materials. Lithium battery anode active materials can be grouped in one of the following categories: lithium intercalation materials (including graphite, Li4Ti5O12); lithium alloying materials (including Sn, Si compounds/composites); lithium deposition materials (lithium metal). For the purposes of this document, material properties will be examined for particulate anode active materials (graphite, Li4TiO5, Sn compounds, Si compounds) and for metallic films (lithium metal). It is not within the scope of this document to establish criteria for the test results, as this is usually established between the vendor and customer It is not within the scope of this document to examine the electrochemical properties of anode materials since these are influenced by electrode design.
Collection

High Efficiency IC Engines, 2013

2013-04-09
The 24 papers in this technical paper collection focus on technologies such as advanced and partially mixed combustion, cooled EGR boosting, ignition and direct injection technologies, pressure boosting, intelligent combustion, thermal efficiency including waste heat recovery, fully variable valvetrains.
Collection

High Efficiency IC Engines Concepts, 2014

2014-04-01
This technical paper collection focuses on technologies such as advanced and partially mixed combustion, cooled EGR boosting, ignition and direct injection technologies, pressure boosting, intelligent combustion, thermal efficiency, fully variable valvetrains, and other new and developing technologies.
Collection

Natural Gas Engines and Vehicles, 2013

2013-04-09
The 9 papers in this technical collection cover fuel injection, combustion, controls, performance and emissions of SI engines fueled with methane based fuels such as natural gas, producer gas, coke oven gas or hydrogen-natural gas blends.
X