Refine Your Search

Topic

Author

Affiliation

Search Results

Magazine

SAE Vehicle Electrification: February 11, 2014

2014-02-11
Inside the cell walls The high cost of lithium-ion batteries is a prison that has largely kept electric vehicles off the street; the keys to their release are more effective—but not more expensive—cell chemistries.
Standard

Test Method for Catalytic Carbon Brake Disk Oxidation

2013-12-04
WIP
AS6289
The scope of the test method is to provide stakeholders including fluid manufacturers, brake manufacturers, aircraft constructors, aircraft operators and airworthiness authorities with a relative assessment of the effect of deicing chemicals on carbon oxidation. This test is designed to assess the relative effects of runway deicing chemicals by measuring mass change of contaminated and bare carbon samples tested under the same conditions.
Standard

Cables, Fiber Optic, Aerospace, General Specification For

2018-04-04
WIP
AS8041
This SAE Aerospace Standard (AS) defines the testing methods for all aerospace optic cables. The application of the test methods are defined in the slant sheets. Technical, dimensional, mechanical and operating performance requirements for the associated aerospace fiber optic cables are detailed in the applicable specification slant sheet. In the event of conflict between this standard and the slant sheet, the slant sheet shall take precedence.
Standard

Missionized Wear Testing

2019-01-02
WIP
ARP6979
Publicize Aircraft Recommended Practice for Missionized Wear Testing on Wright Patterson’s Landing Gear Test Facility’s 168i dynamometer.
Standard

Performance based packaging standard for lithium batteries as cargo on aircraft

2016-03-18
WIP
AS6413
This standard is intended to demonstrate and document the control of the potential hazards from lithium cells or batteries (UN 3090 and 3480) when transported as cargo on aircraft. [still need to identify if we are addressing global (external fire) or local (battery internal failures)] This standard addresses the need to control the hazards which might arise from a failure from an individual cell by containing the hazards within the package. This specific hazards addressed within this standard are: • Uncontrolled fire • Rapid overpressure pulse within compartment
Standard

Epoxy Installation Techniques for Aerospace Fiber Optic Assemblies

2019-03-28
WIP
ARP7983
Describes the different types of epoxies, methods of mixing, installation and inspections into optical connectors/terminus. Illustrate typical examples of processing equipment and tooling. Highlight critical parameters and potential failure modes during epoxy processing.
Standard

ARC Fault Interrupter, 270 VDC

2019-04-27
WIP
AS6087
Develop a standard for testing and evaluating direct current arc fault detection and interruption technologies.
Standard

Aerospace Epoxy Technologies

2019-04-05
WIP
AIR7993
To detail the different epoxy types available for different aerospace applications which require different temperature ranges. Explain incoming/final inspection requirements and storage requirements. Examine the epoxy chemical make up with explanations of purpose in performance.
Standard

Landing Gear Based Weight and Balance Systems

2019-04-18
WIP
AIR6941
This document outlines historical systems which have used the landing gear as a sensor or installation point for full aircraft weight and balance systems. A number of systems have been developed, installed, certified, and placed in service but few systems remain in regular use. The document will capture the history of these systems, reasons (where known) for their withdrawal from service, and lessons learned.
Standard

Advanced methods for Wire Selection and Sizing for Aerospace applications

2019-05-30
WIP
AIR7497
This SAE Aerospace Information Report is intended to provide advanced methods for wire selecting and sizing in aerospace application as a continuation of AIR6540, Fundamentals in Wire Selection and Sizing for Aerospace Applications. Also, it will provide valuable information for the electrical design engineer to verify the proper wire selection and validate a set of system design requirements which includes meeting environmental and installation constraints.
Standard

Wheels - Radial Impact Test Procedure - Road Vehicles

2019-05-22
WIP
J3203
The SAE recommended practice provides a uniform laboratory test procedure for evaluating radial(road hazard) impact collision resistance of all wheels intended for use on passenger vehicles and light trucks.
X