Refine Your Search

Topic

Author

Affiliation

Search Results

Standard

Test Method for Catalytic Carbon Brake Disk Oxidation

2013-12-04
WIP
AS6289
The scope of the test method is to provide stakeholders including fluid manufacturers, brake manufacturers, aircraft constructors, aircraft operators and airworthiness authorities with a relative assessment of the effect of deicing chemicals on carbon oxidation. This test is designed to assess the relative effects of runway deicing chemicals by measuring mass change of contaminated and bare carbon samples tested under the same conditions.
Collection

Vehicle Aerodynamics, 2018

2018-04-03
Vehicle aerodynamic development, drag reduction and fuel economy, handling and stability, cooling flows, surface soiling and water management, vehicle internal environment, tyre aerodynamics and modelling, aeroacoustics, structural response to aerodynamic loading, simulating the on-road environment, onset flow turbulence, unsteady aerodynamics, fundamental flow structures, new test methods and facilities, new applications of computational fluid dynamics simulation, competition vehicle aerodynamics.
Standard

Missionized Wear Testing

2019-01-02
WIP
ARP6979
Publicize Aircraft Recommended Practice for Missionized Wear Testing on Wright Patterson’s Landing Gear Test Facility’s 168i dynamometer.
Standard

Landing Gear Based Weight and Balance Systems

2019-04-18
WIP
AIR6941
This document outlines historical systems which have used the landing gear as a sensor or installation point for full aircraft weight and balance systems. A number of systems have been developed, installed, certified, and placed in service but few systems remain in regular use. The document will capture the history of these systems, reasons (where known) for their withdrawal from service, and lessons learned.
Standard

A Current Assessment of Combining Distortion Types

2019-07-22
WIP
AIR9975
This document will address techniques or methods that have been used within the industry to address the problem of engine stability margin accounting when combinations of distortion types exist in an aircraft installation. Its focus is combining temperature, planar wave, and swirl distortion with time-variant spatial total pressure distortion. Example methodologies will be presented along with example cases where co-existing distortions have been evaluated. It will also address the areas where the industries' knowledge base is lacking (experimental data or computational methods) and the future work that is needed for methodology development in these areas. This document is viewed to be updated every five years as more information (data either experimentally or analytically) becomes available.
Standard

Wheels - Radial Impact Test Procedure - Road Vehicles

2019-05-22
WIP
J3203
The SAE recommended practice provides a uniform laboratory test procedure for evaluating radial(road hazard) impact collision resistance of all wheels intended for use on passenger vehicles and light trucks.
Book

Insight: Fuel Effiency: Fuel Economy Testing (DVD)

2015-04-15
"Spotlight on Design: Insight" features an in-depth look at the latest technology breakthroughs impacting mobility. Viewers are virtually taken to labs and research centers to learn how design engineers are enhancing product performance/reliability, reducing cost, improving quality, safety or environmental impact, and achieving regulatory compliance. As global concerns about the negative consequences of greenhouse gases on the environment increase, regulatory agencies around the world are taking serious steps to address the issue of tailpipe emissions In the episode "Fuel Efficiency: Fuel Economy Testing" (12:01), engineers at the EPA’s National Vehicle and Fuel Emissions Laboratory demonstrate how different vehicles are tested for emissions, and AVL’s technical team shows how accurate tailpipe emissions can be measured and reported.
Collection

Multi-Dimensional Engine Modeling, 2017

2017-03-28
This collection covers advances in the development and application of models and tools involved in multi-dimensional engine modeling: advances in chemical kinetics, combustion and spray modeling, turbulence, heat transfer, mesh generation, and approaches targeting improved computational efficiency. Papers employing multi-dimensional modeling to gain a deeper understanding of processes related to turbulent transport, transient phenomena, and chemically reacting, two-phase flows are included in this collection.
Technical Paper

The Modeling of Mold Filling in Structural Reaction Injection Molding

1996-04-01
91A118
The main use of FRC in automobiles, with the exception of a few specialized low volume vehicles, has been until now in semistructural parts. One of the most promising process in development today, that may play major role in future structural composite fabrication, is based on SRIM technology. The rapid and extensive introduction of this process goes also through the development of deeper theoretical knowledge of the process and the development of computer simulation to aid mold design and choice of proper processing parameters. To contribute SRIM advancement, a preliminary model has been developed for viscosity changes, extent of the reaction and temperature rises, associated with the mold filling stage, as well as a simple software to evaluate the pressure drop through different combinations of reinforcements.
Technical Paper

Integration and Validation of Sheet Metal Forming Simulation Computer Programs Into the Design Process

1996-04-01
91A121
In order to improve the design of drawn parts and to reduce the number of trial and error tests, Renault has undertaken the development and the validation of various finite element procedures and codes. This paper describes the function of each software and its level of integration into the design process. One of them is already an operational tool used be planners whilst the others are still in the validation phase. Selected examples show typical applications of the computer programs on automotive parts.
Technical Paper

Critical Compression Loads on Aluminum Honeycomb Panels

1996-04-01
91A131
The purely theoretical evaluation of critical compression loads seems complex and not very reliable in the case of honeycomb panels, on account of the numerous parameters in play and their complex interrelationships. This report provides the designer with a fast tool for preliminary calculations, consisting of a finite-element mathematical model with elastic-linear code (which can be processed using a PC), which makes it possible to obtain information very closely resembling the real situation.
Technical Paper

Finite Modeling of Sheet Stamping Operations

1996-04-01
91A089
A wide variety of choices confront the potential user of finite element modeling (FEM) for sheet forming analysis. In the first part of this paper, a brief summary of the basic formulations available and sample references to them are provided. Several kinds of finite element models have been developed for analyzing sheet forming operations at OSU and in the Center for Net Shape Manufacturing. These variations began with in-plane FEM and grew into 3-D versions. In the second part of this paper, some key conclusions from these developments will be summarized. More recently, a section analysis program (SHEET-S) has been prepared and transferred to industry. The capabilities and limitations of SHEET-S will be presented in greater detail, including comparisons with experiments and industrial trials.
Technical Paper

A Driving Simulator Using Microprocessors

1988-03-01
871156
An inexpensive driving simulation system with sufficient fidelity has been developed. The system produces motion cues of four degrees of freedom, visual and auditory cues, and control feel on the steering wheel. This paper describes the features of this newly developed system and gives examples that demonstrate its effectiveness. The motion cues provided in this system are yaw, heave, and lateral and fore/aft accelerations. The lateral and fore/aft accelerations are simulated by tilting the simulator compartment. A computer-processed road image is given through a CRT monitor. The restoring torque of the steering wheel is produced by an electrical servosystem via a coil spring. Cruising sound is given in order to improve speed perception. Since the system uses digital computers, the vehicle characteristics are altered easily by merely rewriting the software. This enables us to simulate special vehicle dynamics such as front & rear wheel steering.
Technical Paper

A Study on the Performance of Guideway Bus Steering Control System

1988-03-01
871231
In this paper a computer simulation study on the effects of steering parameters on lateral dynamics of the guideway bus to contribute to a development practice of designing optimum steering control system are dealt with. A stability limit of vehicle lateral motion is analyzed and an emphasis is laid on the effects of moment of inertia of a conventional steering wheel and lateral elasticity of the guide rail which have proven to reduce the critical vehicle speed. It is pointed out conclusively that a normal bus equipped with additional simple guidance equipments can be guided smoothly on a simple guideway at adequately high vehicle speed.
Technical Paper

A Numerical Simulation of the Unsteady Laminar Flame Propagation in a Closed Cylindrical Combustion Bomb

1988-03-01
871174
Unsteady laminar flame propagation confined in a closed cylindrical combustion bomb is studied by numerical computation for an axisymmetric two-dimensional laminar flame. Computation includes complete two-dimensional unsteady Navier-Stokes equations of change for a chemically reacting propane-air mixture. Implicit Continuous fluid Eulerian, Arbitrary Lagrangian Eulerian finite difference technique, simplified reaction kinetics models, and artificial flame stretching transformation and inverse transformation were adopted in the calculation. Physically realistic flame behavior can be demonstrated even with rather coarse computing cell size, simplified reaction kinetics models, and personal computer level low power computing machines.
Technical Paper

Guidelines on the Use of Experimental Sea for Modeling and Understanding Road Noise in Cars

1999-05-17
1999-01-1704
Over the last years, SEA has been recognized as a useful tool to model and analyze the high-frequency vibro-acoustic behavior of fully assembled complex structures. This paper discusses the experimental derivation of the loss factor model of a passenger car. The paper outlines the different steps which need to be taken to obtained a fully validated experimental SEA model. This includes the subdivision into subsystems, the PIM measurement campaign, the derivation of the loss factors and their associated confidence levels and the model validation. The paper further details how the experimental SEA model was used to quantify and investigate the airborne and structure-borne contributions to the interior noise level for a road noise test condition. The operational power inputs to the vehicle were indirectly determined from operational response measurements. A contribution analysis showed that airborne noise sources dominated structure-borne noise sources above 500Hz.
Technical Paper

Calculating Partial Contribution Using Component Sensitivity Values: A Different Approach to Transfer Path Analysis

1999-05-17
1999-01-1693
Transfer Path Analysis (TPA) is a widely used methodology in Noise, Vibration and Harshness (NVH) analysis of motor vehicles. Either it is used to design a vehicle from scratch or it is applied to root cause an existing NVH problem, TPA can be a useful tool. TPA analysis is closely related to the concept of partial contribution. The very basic assumption in TPA is that the summation of all partial contributions from different paths constitutes the total response (which could be either tactile or acoustic). Another popular concept in NVH analysis of vehicles is the component sensitivity. Component sensitivity is a measure of how much the response changes due to a change in one of the components of the system, i.e., the thickness of a panel or elastic rate of an engine mount. Sensitivity rates are more popular among CAE/Simulation community, simply because they are reasonably easy to calculate using mathematical models.
Technical Paper

Process to Achieve NVH Goals: Subsystem Targets via “Digital Prototype” Simulations

1999-05-17
1999-01-1692
A process to achieve vehicle system level NVH objectives using CAE simulation tools is discussed. Issues of modeling methodology, already covered adequately in the literature, are less emphasized so that the paper can focus on the application of a process that encompasses objective setting, design synthesis, and performance achievement using simulation predictions. A reference simulation model establishes correlation levels and modeling methods that are applied to future predictions. The new model, called a “Digital Mule”, is an early new product “design intent” simulation used to arrive at subsystem goals to meet the vehicle level NVH objectives. Subsystem goals are established at discrete noise paths where structure borne noise enters the body subsystem. The process also includes setting limits on the excitation sources, such as suspension and powertrain.
Technical Paper

Modeling and Measurement of Occupied Car Seats

1999-05-17
1999-01-1690
An overview of model development for seated occupants is presented. Two approaches have been investigated for modeling the vertical response of a seated dummy: finite element and simplified mass-spring-damper methods. The construction and implementation of these models are described, and the various successes and drawbacks of each modeling approach are discussed. To evaluate the performance of the models, emphasis was also placed on producing accurate, repeatable measurements of the static and dynamic characteristics of a seated dummy.
Technical Paper

Representation of Constrained/Unconstrained Layer Damping Treatments in FEA/SEA Vehicle System Models: A Simplified Approach

1999-05-17
1999-01-1680
In this study, a simplified approach to modeling the dynamics of damping treatments in FEA (Finite Element)/ SEA (Statistical Energy) models is presented. The basic idea is to represent multi-layered composite structures with an equivalent layer. The properties of the equivalent layer are obtained by using the RKU (Ross, Kerwin and Ungar) method. The procedure presented here does not require any special pre-processing of the finite element input file and it does not increase the number of active degrees of freedom in the model, thereby making it possible to include the effect of these treatments in large system/subsystem level models. The equivalent properties obtained from RKU analysis can also be used in the SEA system models. In this study, both unconstrained and constrained layer damping treatments applied to simple structures (e.g., flat panels) as well as production vehicle components are examined.
X