Refine Your Search

Topic

Author

Affiliation

Search Results

Journal Article

An Accurate Measurement of Rotation Velocity-Eliminating Measurement Errors Caused by Gear Tooth Shape Unevenness

2011-05-17
2011-01-1651
It is very important to accurately measure rotation frequencies and fluctuations of rotating systems since they cause vibrations and noises, and since they sometimes indicate system malfunctions. Most rotating systems are equipped with electro- or magneto-conductive gears as their components, and rotation pulses are very commonly obtained by installing electromagnetic or electrostatic type sensors closely to target gears, and time dependent (instantaneous) rotation frequencies are obtained from intervals between adjacent pulses. However, since the number of pulses per revolution is relatively small, a method of obtaining instantaneous frequencies from adjacent pulse intervals is not adequate. For these kinds of pulses, instantaneous rotation frequencies are typically derived using the analytic signal (or Hilbert transform) method. In either case, there is an inherent limitation in using rotation pulses obtained from gears.
Journal Article

Measurement Dynamic Range Considerations for Sound Transmission Loss Testing

2011-05-17
2011-01-1650
Highly effective double-wall systems for automotive applications can often have over a 90 dB span in sound transmission loss values between low frequencies, where they are usually least effective and upper frequencies, where they are typically most effective. Particularly for 16-bit measurement systems, but even for 24-bit systems, this can represent a very difficult scenario for measurements in either the source and/or receiving chamber(s). A methodology to balance the observed dynamic ranges in both source and receiving chambers is presented and discussed in this paper. An improved sound transmission loss measurement system can therefore be implemented which reduces the potential of overload or noise floor contamination occurring in measurements within either chamber. Low frequency SPL requirements for the source chamber speaker system and flanking noise issues with adjacent test chambers can also be typically reduced.
Technical Paper

Acoustic Test Facility Capabilities at Gulfstream Aerospace

2011-05-17
2011-01-1647
Gulfstream Aerospace Corporation (GAC) owns and operates an Acoustic Test Facility (ATF) in Savannah, GA. The ATF consists of a Reverberation Chamber, Hemi-Anechoic Chamber, and a Control Room. Types of testing conducted in the ATF include Transmission Loss, Sound Power, and Vibration testing. In addition to accommodating typical types of acoustic testing, the ATF has some unique capabilities. The ATF can be used to conduct testing at cold temperatures representative of up to 45,000 ft flight altitude, while simultaneously taking Transmission Loss measurements of the chilled test sample. Additionally, the ATF has the capability of conducting Transmission Loss testing of a full mockup of the aircraft sidewall, including a section of fuselage, all the thermal/acoustic materials up to and including the interior decorative panel. A sound source capable of very high amplitudes at high frequencies is required to obtain good measurements from testing multiple wall systems such as this.
Technical Paper

Development of an Experimental Facility to Characterize Performance, Surge, and Acoustics in Turbochargers

2011-05-17
2011-01-1644
A cold turbocharger test facility was designed and developed at The Ohio State University to measure the performance characteristics under steady state operating conditions, investigate unsteady surge, and acquire acoustic data. A specific turbocharger is used for a thermodynamic analysis to determine the capabilities and limitations of the facility, as well as for the design and construction of the screw compressor, flow control, oil, and compression systems. Two different compression system geometries were incorporated. One system allows compressor performance measurements left of the surge line, while the other incorporates a variable-volume plenum. At the full plenum volume and a specific impeller tip speed, the temporal variation of the compressor inlet and outlet and the plenum pressures as well as the turbocharger speed is presented for stable, mild surge, and deep surge operating points.
Technical Paper

Spirit AeroSystems Acoustics Lab: Measurement and Analysis Capabilities

2011-05-17
2011-01-1643
Previously part of a larger OEM, Spirit AeroSystems became a standalone company 5 years ago and is currently a Tier One supplier of aerostructures. Products include fuselage components, wing structures, engine struts and nacelles, and at the request of various OEMs, fully stuffed fuselages and podded engines where all of the wiring, heating, duct work, etc. is installed prior to delivery. While operating as part of the Propulsion Structures and Systems Business Unit, the design, testing and analysis services provided by the acoustics lab potentially impact all programs at all stages of development because of increasing noise regulations and material certification requirements for implementation in high noise environments.
Technical Paper

Reciprocal Measurements of Transfer Functions for Auralization

2011-05-17
2011-01-1661
Many applications in acoustics, such as transfer path analysis and synthesis (the well-known tools for troubleshooting and sound design of vehicle interior or exterior noise), require the measurement of transfer functions. Several methods are available to determine the transfer functions between identified sources and selected receiver locations. For example, transfer functions can be obtained by means of direct or reciprocal measurements. Due to errors and restrictive constraints during the measurements, the results of the two methods differ. The quality of measured transfer functions must be evaluated with respect to the auralization of the synthesized receiver signals or even the auralization of individual noise shares caused by a specific source and transmitted via one or a combination of paths. This paper compares the different measurement techniques of transfer functions in theory and in practice.
Technical Paper

A Pragmatic Approach to Production NVH Test of Seat Adjusters

2011-05-17
2011-01-1659
A powered seat adjuster is a complex mass-produced assembly that is heavily optimized for low cost and light weight. The consequence is an inevitable degree of uncontrolled variation in components, subassemblies, and final product. Automakers are driving an exceptional focus on quality and the showroom experience of the car buyer is paramount. Therefore, any seat adjuster with the potential to not satisfy the customer's expectation is likely to be screened on the production line. This paper describes NVH metric design in the context of automated production line detection of seat adjuster defects. A key requirement of the production environment is that the metrics offer intuitive explanations of possible defects and are based on industry-standard formulations. The metric set is a hybrid of objective and subjective parameters with a focus on ensuring a robust sorting process that maximizes detection while minimizing the possibility of failing acceptable product.
Journal Article

Advanced Source Localization Techniques Using Microphone Arrays

2011-05-17
2011-01-1657
Microphone arrays used in vehicle acoustics are mainly designed for fast setup and basic evaluation (e.g. using delay-and-sum beamforming) resulting in a restriction to free field environments. Applications in vehicle interiors require advanced source localization techniques taking into account the reflections at the different panels appearing as mirror sources. Coherence filtering techniques allow for the detection of these mirror sources. An additional sensor is placed as a reference close to the main source. This reference signal is used to filter the array signals increasing the overall dynamic range of the acoustic source mapping. The discrimination of the original source and the reflections is obtained by manipulating the impulse responses between the reference signal and all microphone signals.
Technical Paper

Advanced Tire Noise Pass by Noise Solution Meets ISO 13325 and the Recently Updated ISO 362 Standards

2011-05-17
2011-01-1654
Pass by noise is a complex test that requires meeting several different standards with regard to the physical track layout, measurement systems, data acquisition, triggering, processing and analysis. Overview of the pertinent standards for Tire and Vehicle pass by testing is provided along with the description of development of an advanced solution to meet our specific needs. Key features of the solution are provided along with the lessons learned from our operation of the system at our facility and several other test tracks.
Journal Article

Measurement of Sound Transmission Loss Properties in Single & Multi-layered Systems - A Comparative Study between Two-room and Standing Wave Tube Techniques

2011-05-17
2011-01-1653
Several methods have been established to measure the normal incidence transmission loss of noise control materials using the standing wave tube. In the automotive NVH field, multi-layered systems are common-place, for example in the interaction between the traditional mass-decoupler dash insulator and the front dash sheet metal. Most of the sound transmission loss studies utilizing the standing wave tube have so far been focused on single layer systems with only a limited number of studies on multi-layered systems. Therefore there is only some degree of information on the correlation between this said method and the more widely accepted two-room methods of determining sound transmission properties in these systems.
Technical Paper

Comparisons of Global Drive-By Noise Regulations and Levels for Medium and Heavy Duty Trucks

2011-05-17
2011-01-1612
As North American truck manufactures have entered the global market it has become apparent that there are widely varying drive-by noise regulations required in various areas of the world. This paper will describe differences between various test procedures, track layouts, and required levels. Data will be presented showing vehicle results from various procedures, used to quantify differences in noise levels between a range of procedures. Countries were ranked from least restrictive to most restrictive based on test procedures and legal market requirements.
Technical Paper

Drive by Noise System and Corresponding Facility Upgrades for Test Efficiency, Data Quality and Customer Satisfaction

2011-05-17
2011-01-1611
An existing pass by noise data acquisition system was upgraded to provide the sophisticated data analysis techniques and test site efficiency required to comply with the current and future drive by noise regulations. Use of six sigma tool such as voice of the customer helped in defining the customer requirements which were then translated into the desired engineering characteristics using QFD. Pugh concept matrix narrowed down the best option suitable for the test site modifications taking into account the critical constraints such as test complexity, system cost & transparency to the existing drive by noise setup. Features of the new system include data telemetry, frequency analysis, portability and efficient data management through the use of advanced data acquisition system. Wireless mode of the data transmission helped significantly avoid most of the test site modifications, which in turn helped to reduce the overall system implementation cost.
Journal Article

Development of the J2825 On-Highway Motorcycle Sound Test Procedure

2011-05-17
2011-01-1614
In response to a growing need for a practical and technically valid method for measuring exhaust sound pressure levels (SPL) of on-highway motorcycles, the SAE Motorcycle Technical Steering Committee has developed Surface Vehicle Recommended Practice J28251, “Measurement of Exhaust Sound Pressure Levels of Stationary On-Highway Motorcycles,” which includes a new stationary sound test procedure and recommendations for limit values. Key goals of the development process included: minimal equipment requirements, ease of implementation by non-technical personnel, and consistency with the federal EPA requirements; in particular, vehicles compliant with the EPA requirements should not fail when assessed using J2825. Development of the recommended practice involved a comprehensive field study of 25 motorcycles and 76 different exhaust systems, ranging from relatively quiet OEM systems to unbaffled, aftermarket exhaust systems.
Journal Article

Contributors to Lower Frequency Pass-by Noise Levels under Cruise Conditions

2011-05-17
2011-01-1613
With increasing use of the constant speed pass-by conditions to capture the noise generated by this portion of the vehicle operating cycle, knowledge of the contributing sources of noise was become increasingly important. For frequencies above 400 Hz, the noise is dominated by tire/pavement noise as can be demonstrated by comparing on-board sound intensity (OBSI) measurements to constant speed pass-by noise levels. At lower frequencies, direct on-board measurements become more difficult as the tire/pavement noise source strength decreases with decreasing frequency and microphone induced wind noise increases. To investigate the contribution of sources at these lower frequencies, cruise and coast pass-by measurements were made for a number of different pavement types and two different tire designs at test speeds of 56, 72, and 97 km/h over a frequency range from 50 to 10,000 Hz. OBSI measurements were also conducted for these same conditions.
Technical Paper

Vehicle Pass-by Noise Estimations for Component-Level Design

2011-05-17
2011-01-1608
Design parameters for automotive components can be highly affected by the requirements imposed for vehicle pass-by compliance. The key systems affecting pass-by performance generally include the engine, tires, intake system, and exhaust system. The development of these systems is often reliant on the availability of prototype hardware for physical testing on a pass-by course, which can lead to long and potentially costly development cycles. These development cycles can benefit significantly from the ability to utilize analytical data to guide development of component-level design parameters related to pass-by noise. To achieve this goal, test and analysis methods were developed to estimate the vehicle-level pass-by performance from component level data, both from physical and/or analytical sources. The result allows for the estimation of the overall vehicle-level pass-by noise along with the contributions to the total and dominant frequency content from each of the key noise sources.
Journal Article

Revised ISO 10844 Test Surface: Technical Principles

2011-05-17
2011-01-1607
ISO has revised the 10844 International Standard for test surfaces used in measurement of exterior vehicle and tire noise emission. The revision has a goal to reduce the track to track sound level variation presently observed by 50%, without changing the mean value. ISO has incorporated improved texture measurement procedures, improved acoustic absorption measurement procedures, and has added measurement procedures for track roughness. In addition, specifications for texture, absorption, roughness, planarity, and asphalt mix were revised or added to recognize improved technical methods and to achieve the goal of variation reduction. The specification development was supported by a construction program where four candidate ISO 10844 tracks were constructed in Japan, France, and the US to verify the technical principles and to validate construction process capability. This paper will address the technical changes and reasons for these changes in the revised ISO 10844.
Technical Paper

Synthesis of Drive-by Noise Based on Numerically Evaluated Source-Receiver Transfer Functions Employing the FMBEM

2011-05-17
2011-01-1610
Prediction of the drive-by noise level in the early design stage of an automotive vehicle is feasible if the source signatures and source-receiver transfer functions may be determined from simulations based on the available CAD/CAE models. This paper reports on the performance of a drive-by noise synthesis procedure in which the transfer functions are numerically evaluated by employing the Fast Multipole Boundary Element Method (FMBEM). The proposed synthesis procedure first computes the steady-state receiver contributions of the sources as appearing from a number of vehicle positions along the drive path. In a second step, these contributions are then combined into a single transient signal from a moving vehicle for each source-receiver pair by means of a travel time correction.
Technical Paper

Time-Domain Source Contribution Analysis Method for In-Room Pass-By Noise

2011-05-17
2011-01-1609
This paper presents a new time-domain source contribution analysis method for in-room pass-by noise. The core of the method is a frequency-domain ASQ model (Airborne Source Quantification) representing each noise generating component (engine, exhaust, left and right tyres, etc.) by a number of acoustic sources. The ASQ model requires the measurement of local FRF's and acoustic noise transfer functions to identify the operational loads from nearby pressure indicator responses and propagate the loads to the various target microphones on the sides of the vehicle. Once a good ASQ model is obtained, FIR filters are constructed, allowing a time-domain synthesis of the various source contributions to each target microphone. The synthesized target response signals are finally recombined into a pass-by sound by taking into account the speed profile of the vehicle.
Technical Paper

A Computational Approach to Evaluate the Vehicle Interior Noise from Greenhouse Wind Noise Sources - Part II

2011-05-17
2011-01-1620
For most car manufacturers, aerodynamic noise is becoming the dominant high frequency noise source (≻ 500 Hz) at highway speeds. Design optimization and early detection of issues related to aeroacoustics remain mainly an experimental art implying high cost prototypes, expensive wind tunnel sessions, and potentially late design changes. To reduce the associated costs as well as development times, there is strong motivation for the development of a reliable numerical prediction capability. This paper presents a computational approach that can be used to predict the vehicle interior noise from the greenhouse wind noise sources, during the early stages of the vehicle developmental process so that design changes can be made to improve the wind noise performance of the vehicle.
Technical Paper

Application of Micro-Perforated Composite Acoustic Material to a Vehicle Dash Mat

2011-05-17
2011-01-1623
In recent years several variants of lightweight multi-layered acoustic treatments have been used successfully in vehicles to replace conventional barrier-decoupler interior dash mats. The principle involved is to utilize increased acoustic absorption to offset the decrease in insertion loss from the reduced mass such that equivalent vehicle level performance can be achieved. Typical dual density fibrous constructions consist of a relatively dense cap layer on top of a lofted layer. The density and flow resistivity of these layers are tuned to optimize a balance of insertion loss and absorption performance. Generally these have been found to be very effective with the exception of dash mats with very high insertion loss requirements. This paper describes an alternative treatment which consists of a micro-perforated film top layer and fibrous decoupler layer.
X