Search Results

We developed amorphous alloy thin films having TCR(temperature coefficient of resistivity) less than ±5 ppm/°C for strain gauge applications. Thin film strain gauges are directly formed on metal substrates insulated with SiO2. These gauges have excellent aging stability at high temperature. The resistivity shows a drift in ▵R/R less than ±0.03% at 120°C in 1000 hours. We developed a pressure sensor and an acceleration sensor with high accuracy and reliability, employing these gauges.

This paper describes the investigation into the contact pressure and incidental deformation on the contact surface of the piston skirt which comes in contact with the cylinder bore in operation. Focused on the single piston static tests in the first place, relationship between the contact pressure on said skirt and the strains developed inside the skirt, and the relationship between the deformation of skirt face and the strains inside the skirt were studied. Then, the dynamic contact pressure onto the skirt in operation and the amount of deformation were calculated based on the relationships mentioned above using the factor of dynamic strains measured on an engine in operation. The deformation of skirt calculated using said dynamic strains was verified by the direct measurement of the skirt deformation. It was demonstrated that the thrust side of a piston skirt was largely deformed due to enlarged contact pressure caused by the piston slap subsequent to firing top dead center.

This paper reports the results of a study into a preview control that uses the displacement of the road surface in front of the vehicle to improve for front and rear actuator responsiveness delays, as well as delays due to calculation, communication, and the like. This study also examined the effect of a preview control using the eActive3 electric active suspension system, which is capable of controlling the roll, pitch, and warp modes of vehicle motion.

Aiming at improved reliability and cost reduction of position sensors for automobiles, we tackled with the challenge of developing long life contact type potentiometer which has a simple construction and cost advantage. We made clear the wear characteristics of the resistor materials and the mechanism how noise occurs, and developed a long life, low noise resistor material, and the double - layer resistor structure which has excellent characteristic in durability. We also clarified the ways of using brushes according to applications through the investigation of the relationship between the contact shape and the amount of wear of the resistor. Based on these investigation, we have developed a highly reliable throttle position sensor and a long life vehicle height sensor.

In this paper, we discuss vehicle directional stability and introduce advanced stability control (ASTC) to stabilize the vehicle during severe cornering. Vehicle behavior in a transient steering condition during severe cornering was analyzed by computer simulation. It was found that applying an external yaw moment makes the vehicle more stable. The effect of controlling the brake force response is also evaluated by simulation to determine the brake actuator response criteria. The actual vehicle test was performed with a pylon slalom using a hydraulic brake actuator. It is verified that the ASTC stabilizes the vehicle for transient steering maneuvers.

It is well known that the self-aligning torque decreases before lateral force is saturated. Focusing on this self-aligning torque change, an estimation method has been developed to detect the friction condition between steered wheels and road surface before the lateral force reaches the friction limit. The lateral grip margin (LGM) is defined based on the self-aligning torque change, which is obtained using the EPS torque and motor current information. The LGM is theoretically analyzed based on the tire model and experimentally verified through the full-scale vehicle test. Moreover, the estimated LGM is applied for the chassis control systems to improve the vehicle dynamics performance.

There are such outside door handles called smart handles which have a transmitting antenna, a lock/unlock sensor, and a sensor detection circuit, with which operation of door lock is possible just by "touching" the electrostatic-capacitance type sensor of the handles.As the design of the outside handles, body color painting and Cr plating are adopted. However, if plating is applied over the entire surface of a smart handle, electromagnetic waves transmitted from the antenna will be blocked since plating material is electrically conductive. In addition to this, touching a part other than the sensor may change the electrostatic-capacitance of the sensor, which results in unwanted functioning of the lock/unlock sensor. Because of this, only part of the handle, which does not hinder the transmission of electromagnetic waves and does not cause unwanted functioning, is covered by plating, that is called, "Partially plated specifications" (Figure 1).

The conventional hydraulic valve lifters, which eliminate the valve clearance adjustment, normally use the pressurized engine lubricant for the working fluid. We have developed a quite new type lifter, named “self-contained hydraulic valve lifter”, which possesses the working fluid in itself. Because the new type lifter is independent of the pressurized engine lubricant, it has some advantages, especially that it can be applied to the existing engine using the mechanical valve gear without almost any engine modifications. And we have confirmed that the self-contained hydraulic valve lifter has good characteristics and reliability and have applied it to the mass production engine (i.e. Toyota 1.3L gasoline engine) for the first time in the world. This paper describes the construction, the characteristics and the reliability of this lifter.

As a process that enables the high-speed and continuous forming of lengthy materials with a constant cross-sectional configuration, roll forming offers much higher productivity than the stamping process. However, in case a change must be made to the shape of the cross section, the material must normally be stamped or joined with a part containing a separate shape. This affects productivity, increases the number of pieces, and degrades the material's appearance. This report describes the roll-forming technology that we developed, in which the cross section of the material can be changed gradually. This method adopts a system which uses a movable and rotatable roll-stand that enables high-speed, continuous roll-forming processes.

We have developed a power sliding door (PSD) system driven by a push-pull cable. The door closure and slide are operated by different actuators to limit the force required for a compact, light-weight drive unit. This paper introduces the concept of the PSD system using a push-pull cable drive. Two new technologies to achieve the PSD system are also described. One is the door position control for increasing the push-pull cable reliability. The other is a compact position sensor to accurately detect the sliding door's position.

AISIN SEIKI CO., Ltd. Started the production of electronically controlled hydraulic automatic transmissions for medium-duty trucks and buses in 1989. The number of vehicles on the Japanese market in which this system is adopted is increasing steadily. After re-examining market needs, AISIN SEIKI CO., Ltd. has newly developed an electronically controlled hydraulic automatic transmission A580 which focuses on improved input capacity, driving performance and fuel economy for medium-duty trucks and buses and lessens learnt from experience.