Search Results

Eight SUMMA passivated sampling canisters were shipped to the Russian Space Station Mir in February of 1995 to assess ambient trace contaminant concentrations. Prior to flight, the canisters were injected with isotope labeled surrogates and internal standards to measure potential negative impacts on measurement accuracy caused by the trip environmental conditions of launch and return. Three duplicate canister samples were collected in parallel with Russian sorbent samples to acquire data for comparative purposes. A total of 32 target and 13 non-target volatile compounds were detected in each of the samples analyzed. The concentrations of the compounds remained relatively consistent for the three sampling events, and all of the concentrations of detected contaminants were well below both US and Russian Spacecraft Maximum Allowable Concentrations (SMAC). Five different fluorocarbons were consistently detected at relatively high concentrations.

Titanium is a difficult material to fabricate into complex configurations. There is several elevated temperature forming processes available to produce titanium components for aerospace applications. The processes to be discussed are Superplastic Forming (SPF), hot forming and creep forming. SPF uses a tool that contains the required configuration and seals around the periphery so inert gas pressure can be used to form the material. Of the processes to be discussed, this is the one that can produce the most complex shapes containing the tightest radii. A variation of the process combines an SPF operation with diffusion bonding (SPF/DB) of two or more pieces of titanium together to produce integrally stiffened structure containing very few fasteners. Another process for shaping titanium is hot forming. In this process, matched metal tools, offset by the thickness of the starting material, are used to form the part contour at elevated temperature.

With the increasing usage of composites for aerodynamic surfaces, the use of bonded composite repair processes are becoming more common. The repair process remains a largely manual process, with repair technicians scarfing or stepping, tracing the plies, fabricating repair patches and finally bonding the patch. The patch fabrication process becomes increasingly tedious and tiring due to cutting and tracing of each individual ply twice for thermal surveying and the final repair patch. We have developed a system that can replace the tracing and cutting components of the fabrication process using low cost, commercial off the shelf (COTS) tools. We present the ply boundary extraction method used and detail the nesting algorithm used to produce the final plies. Our software is benchmarked against the manual process with a list of successfully cut materials using a low cost fabric cutter with a steel drag blade.

Engineering plastics are now available for use on lightly loaded aircraft structure. These materials have excellent cost benefits as well as producibility benefits over their hand laidup predecessors. They are especially useful in the strut and nacelle areas where many of the fairings are attached for aerodynamic purposes only and may have rather complicated contours. In addition to lower costs, the manufacturing process is consistent, unlike hand laidup parts, which often require rework. In the strut and nacelle area one of the major requirements for all parts is sonic durability. This paper is intended to explain the test setup and test procedure for sonic testing of thermoplastics and thermosets and the results of the testing up to this point. Included in this explanation will be the assumptions made, the test setup, results of the testing and conclusions drawn from the testing.

One of the most common damages occurred found on commercial airframes are dents and gouges. The usual repair for these damages includes installation of metallic doublers with rivets or with hi-loks. Sometimes these doublers are of complex design, because of multiple angles of the original damaged skin. Many times the damages are in hard to reach areas. In these cases the traditional metallic doubler repairs are not only time consuming and but also expensive. As the numerous holes are be drilled through the original structure, its fatigue life is adversely affected. For airline operators, time is valuable and they cannot afford to lose revenue by spending longer time for repairs. The use of bonded composite doublers offers the airframe manufacturers and aircraft repair facilities an alternative repair process that alleviates the abovementioned concerns.

The advantage of higher strength to weight and higher stiffness to weight ratios for composite structure compared to metallic structure is well known in the aerospace industry, especially to commercial airline world. Its increased usage in the airplane structure is a direct reflection of the benefit in reduction of operating costs by lowering the fuel usage. This factor turned out to be more important for the airlines after the September 11, 2001 incident and also due to the increase in fuel prices. Besides reduction in the operating costs, airlines are seeking ways to reduce their maintenance costs. Most of the damage to the aluminum structure airplanes is attributed to corrosion. The non-metallic composite structure has an excellent property of resistance to corrosion. The structure is more damage tolerant due to the absence of fastener holes. As a result, its increased usage serves the airlines by lowering the maintenance and inspection costs.

Boeing needed a process to replace hand drilling for floor panel holes and galley and lavatory mounting locator holes in the floor grid of the completed 737 fuselage. Electroimpact developed a process, and the 737 AFDE machine, that is a substantial improvement over existing technology. It provides full CNC control, quick reconfiguration of hole patterns, fast drilling of up to 3000 holes in one 8-hour shift, drills both titanium and aluminum and works inside the fuselage.