Search Results

AFTERCOOLING, coupled with higher pressure turbocharging can increase vehicle engine output. The author thinks that it is possible to anticipate diesel engines being run with compressors supplying air at pressure ratios higher than 2/1. Density ratio is the most important consideration in increasing pressure ratio, since the engine's output is dependent upon weight rather than volume of air supplied. Because the density of the compressed air is dependent upon its temperature at any pressure level, cooling the air after compression results in density increases. This paper describes various methods of after-cooling which increase engine output and fuel economy.

The small wheel type loader has seen its application range extended such that it is now one of the most versatile machines in our industry. However, its effectiveness in tasks other than bucket loading is limited. In order to provide improved tool control characteristics that contribute to efficient multi-task capability, it is necessary to design these characteristics into the base vehicle. The Integrated Toolcarriers recently introduced by Caterpillar fulfill this requirement. This paper discusses the design objectives and summarizes the development program which preceded their introduction.

A new Caterpillar Wheel Loader has been developed to provide a loader in the 2 cubic meter (2.5 cubic yard) bucket capacity-category. This paper provides a review of the machine design objectives and summarizes the design features included to meet worldwide manufacturing and marketing requirements.

Fatigue failure of machine components subjected to high contact pressures is rapidly becoming recognized as a serious design limitation. Confusion has resulted from grouping three distinct types of contact fatigue failure under the term “pitting” A Geared Roller Test Machine is described that reproduced each of the three modes of failure. The stress-life relationships obtained for rollers tested under conditions of rolling plus sliding correlated well with actual gear performance. The sensitivity of the test to changes in material, micorstructure, and processing variables is demonstrated.

THIS paper presents results which will answer many of the problems facing an engine manufacturer in the selection of the most suitable types and sizes of superchargers to use with a line of engines. Although performance curves of production model diesels are available, decisions are still needed in choosing peak supercharging pressures, drive means, and size and effectiveness of intercoolers, if any. The author describes the use of a typical model to determine response to variation in intake and exhaust conditions, resulting in data which will assist in evaluating engine potentials with any system of supercharging. Thus, supercharger selection for a particular line of engines is aided by knowledge of engine characteristics as a second-stage compressor.

This Paper: 1. Shows that the present spherical rod end manufacturer's rotational tests, which are intended to select the best bearing material, do not necessarily select the best materials for the push/pull linkage requirements of earthmoving machinery. 2. Emphasizes the need to perform push/pull comparative testing as defined in SAE J1367 on spherical rod ends to determine acceptable materials for earthmoving equipment application. This test is in contrast to rotational testing presently being performed by spherical rod end manufacturers.

An eight-stage transonic axial flow compressor was scaled to three-tenths its original size. The scaled compressor was built and tested as a separate component, and as a component of a gas turbine engine. This paper summarizes the work done on this compressor, including the aerodynamic design considerations and overall performance results.

Chromatographic analysis of diesel exhaust indicates a number of low molecular weight hydrocarbons, below C6. Using reactivity index as a criterion, much of the diesel exhaust reactivity can be attributed to ethylene and propylene caused by the thermal decomposition of the fuel. Hydrocarbons in the C4-C7 range, including high relative reactivity olefins, are generally low in volume concentration and therefore contribute little to the overall exhaust reactivity. Hydrocarbons, in terms of parts per million carbon above C7 are low in present diesel engine designs, so individual volume concentrations are generally fractional parts per million. Reactivity per horsepower-hour from diesel engine exhaust is less than that from the one small industrial gasoline engine tested by the heavy-duty truck diesel engine cycle.

This paper first discusses the loads of major significance to various machines and machine parts, and second, considers available methods of measuring, analyzing, and presenting information on loads and stresses. Various engine and machine components are examined from standpoints of loading methods and which loads are likely to be critical on each component. Interrelations between components and machines are also discussed. Tools and methods available to the load and stress analyst are described, with particular emphasis on choices available in methods, instrumentation, and presentation of data. Reasons for preferences in particular situations are given.

TRACTORS operate in a wide range of conditions, from desert to swamp. At all times, the final-drive seals must keep the oil in and the dirt out. In this paper, the authors discuss the latest developments in seal design and the resulting improvements in performance. Efficient performance of a tractor final-drive seal depends upon a number of factors, including: bellows and bellows-boot operation, seal load and area, seal material, wear washer, and gasket structures.

Analytic modeling and analog computer simulation techniques are presented for determining power train transient responses excited by clutch-actuated gear shifts. A method for describing the dynamics of a transmission arrangement having several clutches and interconnected planetary gear sets is considered in detail. Simulation model testing is directed toward optimizing system design parameters and evaluating power train component capability and vehicle shift-feel. Data reduction techniques applied to model responses of torque and speed will yield appropriate spectrums representative of simulated work cycle. The spectrum data are used to predict hours of life for gears, bearings, and driveshafts, according to cumulative fatigue damage theory.

Two new Caterpillar Wheel Loaders have been developed in the 1.2 cubic meter (1.5 cubic yd.) and 1.5 cubic meter (2.0 cubic yd.) bucket capacity categories. This paper provides a review of the design objectives and summarizes the design features included to meet worldwide manufacturing and marketing requirements.

A single-shaft, simple-cycle gas turbine engine has been developed to power 200 kw alternators for standby power and for applications where heat is needed. The engine was designed to be sold and serviced by distributors of earthmoving and industrial machinery. Where feasible, design practices of industrial piston engine powered generator sets were incorporated to facilitate installations of combinations of engine types, and to limit novel and unfamiliar features of the basic turbine engine to those that were considered essential. Individual components and complete engines, initially developed by a research group, have been subjected to a wide variety of laboratory tests to measure performance and develop reliability.

This paper discusses: the needs and benefits of a parts reusability program; the elements required for establishing a parts reusability program; how to determine the reusability limits of a part; the implementation of a parts reusability program; and how to evaluate a parts reusability program. This paper is written and intended for market analysts and engineers working in service organizations worldwide.

For some time, Caterpillar Tractor Co. has been marketing a new transmission control system for wheel-tractor scrapers and off-highway trucks. The new system is composed of an electronic microprocessor control box coupled with an individual clutch modulation hydraulic control. This system has resulted in increased vehicle productivity, improved reliability and serviceability, decreased complexity, and increased commonality of parts. This paper describes the concept, design, and test and evaluation process used to develop the new controls before production.

This paper demonstrates a way of applying an iterative computing technique to a typical engineering design problem, in such a way as to maximize a mathematical expression of the design criteria. Ways of writing this mathematical expression to express design criteria are explained through several illustrative examples. This technique of computer-aided design should allow the engineer to arrive at more than satisfactory designs in a minimum of engineering time.

TVA is an interactive computer program which performs a Torsional Vibration Analysis on lumped mass systems which contain torsional degrees of freedom. This program has two fundamental analyses. The first is Normal Modes which analyzes the natural unforced undamped behavior of the system to give natural frequencies and mode shapes. The second analysis is Frequency Response which analyzes the forced response of a damped system to give response results. TVA is used to analyze engine-auxilary equipment systems as well as vehicle drivetrain systems.

THE HYDRAULIC SYSTEMS for the Caterpillar “G” Series Motor Graders were designed to provide for maximum operator comfort, ease of operation, and optimum control of the vehicle and implements. The use of high pressure closed center systems on these machines produces rapid system response and high hydraulic horsepower to the implement cylinders and motors, and operates with minimum size control components. Components were designed to meet specific system requirements for functional performance, reliability of operation, size and placement on the machine. System goals were met through the use of a variable displacement pressure compensated pump, controlled flow four-way implement valves, and a hydrostatic steering system.

THE CATERPILLAR FOLDED CORE RADIATOR IS A NEW RADIATOR FOR VEHICLES AND STATIONARY ENGINE APPLICATIONS. THE MAJOR OBJECTIVES OF THIS DESIGN ARE TO GIVE THE USER AN INCREASED VALUE COOLING SYSTEM BY REDUCING RADIATOR REPAIR COSTS AND IMPROVING AIR-SIDE PLUGGING RESISTANCE. AS WELL AS PROVIDE THE VEHICLE DESIGNER WITH INCREASED APPLICATION DESIGN FLEXIBILITY. THIS IS TO BE ACCOMPLISHED WHILE MAINTAINING PERFORMANCE AND LIFE GOALS ASSOCIATED WITH THE CONVENTIONAL RADIATOR. THE FOLDED CORE IS A MODULAR DESIGN HAVING THE MODULES INSTALLED AT AN ANGLE TO THE FAN AIR STREAM RESULTING IN THE FOLDED APPEARANCE. COMMON MODULE SIZES ARE USED ACROSS THE MANY RADIATOR APPLICATIONS REDUCING INVENTORY REQUIREMENTS AT THE ASSEMBLY PLANT AND PARTS DEPOTS AND INCREASING INDIVIDUAL MODULE PRODUCTION VOLUME. THIS RADIATOR DESIGN IS REVIEWED FROM CONCEPT TO PRODUCTION.

A new two-speed converter drive, six-speed mechanical drive transmission was designed for a 14 cu yd tractor scraper to provide an efficient and easily controlled power train. Included with a description of the system is a review of the development history, along with a summary of some new features utilized in this design.