AS a basis for the analyses of this symposium, a hypothetical car has been used to evaluate the engine power distribution in performance. Effects of fuel,-engine accessories, and certain car accessories are evaluated. The role of the transmission in making engine power useful at normal car speeds is also discussed. Variables encountered in wind and rolling resistance determinations are reevaluated by improved test techniques. Net horsepower of the car in terms of acceleration, passing ability and grade capability are also summarized.
This study is a joint development project between Chrysler Corporation and CFD Research Corporation. The objective of this investigation was to develop a 3D computational flow and heat transfer model for a vehicle windshield de-icing process. The windshield clearing process is a 3D transient, multi-medium, multi-phase heat exchange phenomenon in connection with the air flow distribution in the passenger compartment. The transient windshield de-icing analysis employed conjugate heat transfer methodology and enthalpy method to simulate the velocity distribution near the windshield inside surface, and the time progression of ice-melting pattern on the windshield outside surface. The comparison between the computed results and measured data showed very reasonable agreement, which demonstrated that the developed analysis tool is capable of simulating the vehicle cold room de-icing tests.
The principles of combustion in a spark ignition engine are discussed. Engine processes and reactions are explained as to the manner in which they influence exhaust composition. The subject is approached by considering how chemical phenomena interact in a complex system such as a spark ignition engine. Special attention is given to the effect on exhaust composition of such factors as engine design and modifications, fuel composition, and engine maintenance.
The flow field contained within ten planes inside a cylinder of a 3.5 liter, 24-valve, V-6 engine was mapped using a three-dimensional Laser Doppler Velocimetry (3-D LDV) system. A total of 1,548 LDV measurement locations were used to construct the time history of the in-cylinder flow fields during the intake and compression strokes. The measurements began during the intake stroke at a crank angle of 60° ATDC and continued until approximately 280° ATDC. The ensemble averaged LDV measurements allowed for a quantitative analysis of the dynamic in-cylinder flow process in terms of tumble and swirl motions. Both of these quantities were calculated at every 1.8 crank degrees during the described measurement interval. Tumble calculations were performed about axes in multiple planes in both the Cartesian directions perpendicular to the plane of the piston top. Swirl calculations were also accomplished in multiple planes that lie parallel to the plane of the piston top.
This paper discusses simplified lumped parameter thermal modeling of power train components. In particular, it discusses the tradeoff between model complexity and the ability to correlate the predicted temperatures and flow rates with measured data. The benefits and problems associated with using a three lumped mass model are explained and the value of this simpler model is promoted. The process for correlation and optimization using modern software tools is explained. Examples of models for engines and transmissions are illustrated along with their predictive abilities over typical driving cycles.
There is a major problem in maintaining the records of the more than 275 million vehicles presently registered throughout the world. Monitoring the life of a given vehicle from its fabrication to its destruction can best be accomplished by the inner facing of major computer programs and a uniform system for vehicle identification. The Vehicle Identification Number (VIN) is the legal identification of the vehicle. Every manufacturer has the responsibility of assigning a unique VIN to each vehicle, in compliance with numerous procedures, standards and laws. The VIN is attached to the vehicle, stamped and embossed on components, and printed on tamper resistant labels. It is printed on hundreds of documents and maintained in numerous files.
PLYMOUTH'S new V-8 engine has a specific output of 0.65 bhp/cu in. and 145-psi bmep — obtained through a combination of high thermal, volumetric, and mechanical efficiencies. Good design, the author points out, has achieved this high output despite the dual-venturi carburetor and the 7.6/1 compression ratio, selected for satisfactory operation on regular-grade fuels. The engine has a bore and stroke of 3.563 × 3¼, weighs 568 lb without flywheel, is 29⅜ in. long, and is designed for optimum response to future compression ratio increases. (A report of oral discussion following presentation of this paper appears on p. 220, following “The New Packard V-8 Engine,” by W. E. Schwieder.)
The Chrysler wind tunnel is a closed-circuit, single-return, semiopen jet facility used for performing engine cooling, transmission cooling, engine compartment airflow, underhood component temperature, air-conditioning, and other types of tests. It operates over a 0-120 mph speed range with 400 hp rear-wheel power absorption capacity. Special provisions have been made for idle, city traffic, and tail wind tests. Facility controls provide precise set-point capability, and comprehensive instrumentation and data acquisition systems permit measurement of many parameters and real time data reduction.
A new tool for analyzing transmissions that use planetary gearsets is presented. With this tool, entire transmissions are usually represented by a single lever, and the calculation of most characteristics is as simple as summing moments of a lever. A miniature cookbook of levers, for various planetary arrangements is included which can be helpful in selecting a planetary to achieve the desired objectives of a user.
A selection of commercially available chromium and chromium-free post phosphate rinses along with a deionized water rinse were evaluated over several zinc and zinc-alloy coated sheet steels. The test specimens were pretreated and electrocoated on-line in an automotive assembly plant. The effect of the rinse treatments on the cosmetic corrosion performance of the substrates, after 5 years of exposure in an outdoor scab corrosion test was determined. After this exposure none of the rinse treatments had performed better than deionized water rinse on zinc and zinc-iron coated sheet. The zinc-nickel coating showed improved scribe creepage when treated with the Cr+6/Cr+3 rinse. Data is provided comparing the concentration of the treatments used vs scribe creepage and chipping corrosion paint loss.
Formula One motorsport competition, ever seeking increases in powertrain responsiveness and efficiency, has utilized electronically-shifted manual transmissions for nearly a decade. With the advent of this technology for passenger car usage ( for example the Magneti Marelli “Selespeed” system), new levels of powertrain electronic control become possible. At the same time, world-wide emission and fuel economy standards have driven powertrain designers to seek transmissions that are multi-faceted; able to offer manual transmission levels of driveline efficiency while simultaneously offering the ability to be automatically controlled. This paper will document a 1995-1996 Chrysler advanced powertrain concept study that culminated in a fully driveable, fully automatic, manual 5 speed transmission Neon coupe.
THE design and construction of the PowerFlite automatic transmission are described by the authors. It is of the torque converter type, some models being water-cooled, while others are direct air cooled. Details of the hydraulic controls are explained, including the one-piece shift valve and the shuttle valve for controlling closed-throttle shifts. It is claimed that this transmission has relative simplicity, light weight, and smoothness of operation.
Most of the current fuel supply specifications, including the key parameters in the transient fuel control strategies, are experimentally determined since the complexity of multiphase fuel flow behavior inside the intake manifold is still not quantitatively understood. Optimizing these specifications, especially the parameters in transient fueling systems, is a key issue in improving fuel efficiency and reducing exhaust emissions. In this paper, a model of fuel spray, wall-film flow and wall-film vaporization has been developed to gain a better understanding of the multiphase fuel-flow behavior within the intake manifold which may help to determine the fuel supply specifications in a multi-point injection system.
A torque converter lock-up clutch was introduced by Chrysler Corporation in a majority of its passenger cars in the 1978 model year. The lock-up clutch improves fuel economy by eliminating torque converter slip in direct gear above a predetermined speed. The clutch and its controls were designed to fit within the confines of the existing transmission. The development of the clutch was primarily concerned with achieving adequate endurance life, good shift quality and isolation of torsional vibrations.
THIS paper discusses the progress of research on the automotive gas turbine and predicts its future potentialities. Comparison of gas turbines and presently used engines shows the possibilities of the gas-turbine applications. Design, construction, and testing of gas turbines are discussed, especially in the light of economy and performance.
An automotive cockpit module is a complex assembly, which consists of components and sub-systems. The critical systems in the cockpit module are the instrument panel (IP), the floor console, and door trim assemblies, which consist of many plastic trims. Stiffness is one of the most important parameters for the plastic trims' design, and it should be optimum to meet all the three functional requirements of safety, vibration and durability. This paper presents how the CAE application and various other techniques are used efficiently to predict the stiffness, and the strength of automotive cockpit systems, which will reduce the product development cycle time and cost. The implicit solver is used for the most of the stiffness analysis, and the explicit techniques are used in highly non-linear situations. This paper also shows the correlations of the CAE results and the physical test results, which will give more confidence in product design and reduce the cost of prototype testing.
Although numerical simulation techniques for sheet metal forming become increasingly maturing in recent years, prediction of springback remains a topic of current investigation. The main point of this paper is to illustrate the effectiveness of a modelling approach where static implicit schemes are used for the prediction of springback regardless whether a static implicit or dynamic explicit scheme is used in the forming simulation. The approach is demonstrated by revisiting the 2-D draw bending of NUMISHEET'93 and numerical results on two real world stampings.
The low noise and linear sound level characteristics of passenger vehicles are receiving increased scrutiny from automotive journalists. A linear noise level rise with increasing engine rpm is the first basic aspect of insuring an acceptable vehicle interior engine noise sound quality. In a typical case of structural response to engine vibration input, interior noise begins to rise with rpm, remains constant or even drops as the engine continues to accelerate, and then exhibits a noise period corresponding to the structure's natural frequency. Frequently this nonlinearity is bothersome to the customer. During the development process, Chrysler's Dodge and Plymouth Neon exhibited just such a nonlinear rise in noise level, heard within the passenger compartment, when the vehicle was accelerated through 4200 rpm.
Vacuum insulation and phase-change thermal storage have been used to enhance the heat retention of a prototype catalytic converter. Storing heat in the converter between trips allows exhaust gases to be converted more quickly, significantly reducing cold-start emissions. Using a small metal hydride, the thermal conductance of the vacuum insulation can be varied continuously between 0.49 and 27 W/m2K (R-12 to R-0.2 insulation) to prevent overheating of the catalyst. A prototype was installed in a Dodge Neon with a 2.0-liter engine. Following a standard preconditioning and a 23-hour cold soak, an FTP (Federal Test Procedure) emissions test was performed. Although exhaust temperatures during the preconditioning were not hot enough to melt the phase-change material, the vacuum insulation performed well, resulting in a converter temperature of 146°C after the 23-hour cold soak at 27°C.