Search Results

The aim of this work is to apply an innovative adaptive ℒ1 techniques to control flutter phenomena affecting highly flexible wings and to evaluate the efficiency of this control algorithm and architecture by performing the following tasks: i) adaptation and analysis of an existing simplified nonlinear plunging/pitching 2D aeroelastic model accounting for structural nonlinearities and a quasi-steady aerodynamics capable of describing flutter and post-flutter limit cycle oscillations, ii) implement the ℒ1 adaptive control on the developed aeroelastic system to perform initial control testing and evaluate the sensitivity to system parameters, and iii) perform model validation and calibration by comparing the performance of the proposed control strategy with an adaptive back-stepping algorithm. The effectiveness and robustness of the ℒ1 adaptive control in flutter and post-flutter suppression is demonstrated.

Scaled models are often used to check the aerodynamic performance of full scale aircraft and airship concepts, which have gone through a conceptual and preliminary design process. Results from these tests can be quite useful to improve the design of unconventional airships whose aerodynamics might be quite different from classical configurations. Once the airship geometry has been defined, testing is required to acquire aerodynamic data necessary to implement the mathematical model of the airship needed by the flight control system to develop full autonomous capabilities. Rapid prototyping has the great potential of playing a beneficial role in unconventional autonomous airship design similarly to the success obtained in the design process of conventional aircrafts.

Newly developed technologies are enabling the design of Unmanned Aerial Vehicles (UAVs) and Micro Air Vehicles (MAVs) with heretofore unrealized capabilities. A tube-launch MAV would allow the increased flexibility to launch an aircraft rapidly without need for a runway or complex launching system, either from a vehicle, installation, or as a man-portable device. The MAV would fill the diameter of the launch tube and deploy aerodynamic lifting and control surfaces after launch. In order to deploy the lifting surfaces the MAV must be capable of deploying control surfaces, negating any tube-imparted roll rate, and developing an optimal flight attitude automatically. An experimental method was developed to characterize the aerodynamics and stability of a blunt body spinning under conditions of roll rate decay in the Clarkson University High Speed Wind tunnel. This method is to be used to evaluate the development of an active roll rate control system for spinning projectiles.

Flow control over aerodynamic shapes in order to achieve performance enhancements has been a lively research area for last two decades. Synthetic Jet Actuators (SJAs) are devices able to interact actively with the flow around their hosting structure by providing ejection and suction of fluid from the enclosed cavity containing a piezo-electric oscillating membrane through dedicated orifices. The research presented in this paper concerns the implementation of zero-net-mass-flux SJAs airflow control system on a NACA0015, low aspect ratio wing section prototype. Two arrays with each 10 custom-made SJAs, installed at 10% and 65% of the chord length, make up the actuation system. The sensing system consists of eleven acoustic pressure transducers distributed in the wing upper surface and on the flap, an accelerometer placed in proximity of the wing c.g. and a six-axis force balance for integral load measurement.

The deployment dynamics of a tape-spring style, folding MAV wing in flight are complicated and an investigation is made using wind tunnel testing. High speed photography is used to characterize the deployment motion of the wing while a force balance records six- axis aerodynamic loading of the model. An in-flight deployment of a folding wing would be advantageous after an autonomous tube launch, however the dynamics are potentially problematic due to buckling. Steady state aerodynamics of prototype tube-launch MAVs are characterized for both rigid body and compliant, rolling wings. Aerodynamic phenomena associated with the significant relative body size are identified. Wing deployments are demonstrated at four different angles-of-attack at single velocity, while an extreme case deployment is shown at a high velocity. Two-piece cylindrical shells are used to retain the wing prior to deployment and are released by hot-wire cutting of retaining lines.

This paper describes the design and development of a virtual environment conceived to support flight operations of an Unmanned Air Vehicle (UAV) used for wind mapping in the proximity of existing or planned wind farms. The virtual environment can be used in pre-flight briefings aiming to define a trajectory from a list of waypoints, to change and eventually re-plan the mission in case of intersection with no fly zones, to simulate the mission, and to preview images/videos taken from the UAV on-board cameras. During flight, the tool can be used to compute the wind speed along the trajectory by analyzing the data streaming from the UAV. The integration of Augmented Reality (AR) techniques in the flight environment provides assistance in remotely piloted landings, and allows visualizing flight and environmental information that are critical to the mission.

Active flow control devices such as zero-net-mass-flux actuators have broad aeronautical applications. Among them, low power and lightweight Synthetic Jet Actuators can be used to improve the performance of flight vehicles, providing load alleviation capabilities, expanding their flight envelope, and preventing catastrophic failure by aeroelastic instabilities. Numerical and experimental investigations are proving that SJAs are effective in actively altering the boundary layer; the effect of the momentum exchange due to the SJAs leads to a rearrangement of streamlines, a virtual aerodynamic shaping that enable changes in the aerodynamics forces acting on the lifting surfaces. This paper discusses development aspects that the authors have been conducting on the topic with applications to load alleviation and flutter suppression for aircraft wings.

The aeroelastic design of highly flexible wings, made of extremely light structures yet still capable of carrying a considerable amount of non-structural weights, requires significant effort. The complexity involved in such design demands for simplified mathematical tools based on appropriate reduced order models capable of predicting the accurate aeroelastic behaviour. The model presented in this paper is based on a consistent nonlinear beam model, capable of simulating the unconventional aeroelastic behaviour of flexible composite wings. The partial differential equations describing the wing dynamics are reduced to a dimensionless form in terms of three ordinary differential equations using a discretization technique, along with Galerkin's method. Within this approach the nonlinear structural model an unsteady indicial based aerodynamic model with dynamic stall are coupled.