Search Results

The number of control actuators available on spark-ignition engines is rapidly increasing to meet demand for improved fuel economy and reduced exhaust emissions. The added complexity greatly complicates control strategy development because there can be a wide range of potential actuator settings at each engine operating condition, and map-based actuator calibration becomes challenging as the number of control degrees of freedom expand significantly. Many engine actuators, such as variable valve actuation and flow control valves, directly influence in-cylinder combustion through changes in gas exchange, mixture preparation, and charge motion. The addition of these types of actuators makes it difficult to predict the influences of individual actuator positioning on in-cylinder combustion without substantial experimental complexity.

Two methods for analyzing and evaluating the environmental control system on an advanced aircraft as described in this paper include the conventional first law energy conservation technique and the second law entropy generation minimization technique. Simplified analytical models of the ECS are developed for each method and compared to determine the validity of using the latter to facilitate the design process in optimizing the overall system for a minimum gross takeoff weight (GTW). Preliminary results have illustrated the importance of taking into account system optimization based on system (or component) efficiency. For instance, even though different values were obtained for the rate of entropy generation, the second law analysis of a shell-in-tube heat exchanger led to an optimum tube diameter of 0.12 in (3.05 mm) when both R-12 and R-114 were used as the refrigerant in the vapor cycle.

A nonlinear eight degree of freedom vehicle model has been used to examine the effects of roll stiffness on handling and performance. In addition, various control strategies have been devised which vary the total roll couple distribution in order to improve cornering capability and stopping distance. Of all cases tested, a controller which varies the total roll stiffness based on roll angle feedback, and continuously updates the roll couple distribution as a function of steering wheel angle, braking input, and the total roll stiffness, yields the greatest improvements in collision avoidance.

Predictable handling of a racecar may be achieved by tailoring chassis stiffness so that roll stiffness between sprung and unsprung masses are due almost entirely to the suspension. In this work, the effects of overall chassis flexibility on roll stiffness and wheel camber response, will be determined using a finite element model (FEM) of a Winston Cup racecar chassis and suspension. The FEM of the chassis/suspension is built from an assembly of beam and shell elements using geometry measured from a typical Winston cup race configuration. Care has been taken to model internal constraints between degrees-of-freedom (DOF) at suspension to chassis connections, e.g. t ball and pin joints and internal releases. To validate the model, the change in wheel loads due to an applied jacking force that rolls the chassis agrees closely with measured data.

Track testing of race cars is expensive and racing series typically limit the amount of testing that can be done on circuit tracks. Because of this, we saw the need to develop a computer model that could simulate a car on a track with any specified surface roughness and with aerodynamic loading acting on the vehicle. This model allows an analysis of the effect of aerodynamic loading on the vertical dynamic response of the vehicle. Vehicle parameters specific to an IMSA GTP car including aerodynamic data from wind tunnel testing and nonlinear shock characteristics were used in this study. Simulations were run for various speeds and ride height configurations and it was found that very small changes in the static settings of the front and rear ride heights can lead to large differences in the resulting ride heights at speed. This can be attributed to the variations in the nonlinear aerodynamic loading as the ride height and speed of the vehicle change.

Rollover prevention is now part of complete vehicle stability control systems for many vehicles. Given that rollover is predominantly associated with vehicles with high centers of gravity, the targeted vehicles for rollover protection include medium and heavy duty commercial vehicles. Unfortunately, the chassis designs of these vehicles are often so compliant in torsion that the ends of the vehicles may have significantly different roll responses at any given time. The potential need to assess and correct for the roll behavior of the front and rear ends of the vehicle is the subject of this paper. Most rollover mitigation research to date has used rigid chassis assumptions in modeling the vehicle. This paper deals with the roll control of vehicles with torsionally flexible chassis based on a yaw-correction system.

In developing a nonlinear steering system model for vehicle simulation, it was determined that proper inclusion of system friction is necessary to correctly predict steering wheel torque response in on-center driving using simulation models. A method to characterize the inherent friction behavior for a given steering gear has been developed and performed on two types of power steering gears: a recirculating ball gear and a rack-and-pinion gear. During this research it was discovered that levels of static and dynamic friction can differ widely for these two types. Therefore this characterization procedure provides a method to ascertain both static and dynamic friction levels. The results from these tests show that friction levels can depend on steering gear input shaft position, steering gear input angular velocity and steering gear loading conditions.

The highly transient operational nature of passenger car engines makes cylinder pressure based feedback control of combustion phasing difficult. The problem is further complicated by cycle-to-cycle combustion variation. A method for fast and accurate differentiation of normal combustion variations and true changes in combustion phasing is addressed in this research. The proposed method combines the results of a feed forward combustion phasing prediction model and “noisy” measurements from cylinder pressure using an iterative estimation technique. A modified version of an Extended Kalman Filter (EKF) is applied to calculate optimal estimation gain according to the stochastic properties of the combustion phasing measurement at the corresponding engine operating condition. Methods to improve steady state CA50 estimation performance and adaptation to errors are further discussed in this research.

Due to titanium's excellent strength-to-weight ratio and high corrosion resistance, titanium and its alloys have great potential to reduce energy usage in vehicles through a reduction in vehicle mass. The mass of a road vehicle is directly related to its energy consumption through inertial requirements and tire rolling resistance losses. However, when considering the manufacture of titanium automotive components, the machinability is poor, thus increasing processing cost through a trade-off between extended cycle time (labor cost) or increased tool wear (tooling cost). This fact has classified titanium as a “difficult-to-machine” material and consequently, titanium has been traditionally used for application areas having a comparatively higher end product cost such as in aerospace applications, the automotive racing segment, etc., as opposed to the consumer automotive segment.

As engines are equipped with an increased number of control actuators to meet fuel economy targets, they become more difficult to control and calibrate. The additional complexity created by a larger number of control actuators motivates the use of physics-based control strategies to reduce calibration time and complexity. Combustion phasing, as one of the most important engine combustion metrics, has a significant influence on engine efficiency, emissions, vibration and durability. To realize physics-based engine combustion phasing control, an accurate prediction model is required. This research introduces physics-based control-oriented laminar flame speed and turbulence intensity models that can be used in a quasi-dimensional turbulent entrainment combustion model. The influence of laminar flame speed and turbulence intensity on predicted mass fraction burned (MFB) profile during combustion is analyzed.

Hydrostatic (hydraulic hybrid) drives have demonstrated energy efficiency and emissions reduction benefits. This paper investigates the potential of an independent hydrostatic wheel drive system for implementing a traction-based vehicle lateral stability control system. The system allows an upper level vehicle stability controller to produce a desired corrective yaw moment via a differential distribution of torque to the independent wheel motors. In cornering maneuvers that require braking on any one wheel of the vehicle, the motors can be operated as pumps for re-generating energy into an on-board accumulator. This approach avoids or reduces activation of the friction brakes, thereby reducing energy waste as heat in the brake pads and offering potential savings in brake maintenance costs. For this study, a model of a 4×4 hydrostatic independent wheel drive system is constructed in a causal and modular fashion and is coupled to a 7 DOF vehicle handling dynamics model.

Three-dimensional simulation has become an indispensable approach to develop improved understanding of ring rolling technology, with validity as the basic requirement of the ring rolling simulation. Cold ring rolling is simple conceptually, however complex to analyze as the metal forming process is subject to coupled effects with multiple influencing factors such as sizes of rolls and ring blank, form geometry, material, process parameters, and frictional effects. Investigating the coupled thermal and plastic deformation behavior (the plastic deformation state and its development) in the deformation zone during the process is significant for predicting metal flow in order to control the geometric and tensile residual stress quality of deformed rings, and to provide for cycle time optimization of the cold ring rolling process.

In this paper, in support of developing an advanced non-pneumatic lunar tire, a dynamic interaction model between non-pneumatic tire and sand is presented using the Finite Element Method (FEM). This non-pneumatic tire is composed of three major components: a critical shear beam, two inextensible circumferential membranes, and deformable spokes. The non-pneumatic tire made of segmented cylinders is described in detail. The tire is treated as an elastic deformable body with the inertia effect is included. Lebanon sand found in New Hampshire is modeled as because of the availability of a complete set of material properties in the literature. The Drucker-Prager/Cap plasticity constitutive law with hardening is employed to model the sand. Numerical results show contact pressure distribution, distributions of various stresses and strains, deformation of non-pneumatic tire, and deformation of sand.

In this paper, the Finite Element Method (FEM) is used to model and simulate the dynamic interaction between non-pneumatic tire and sand with obstacle to investigate the influence of obstacle on performance of the non-pneumatic tire. The non-pneumatic tire consists of three major components: two inextensible circumferential membranes, a critical shear beam, and a group of deformable spokes. The non-pneumatic tire fabricated of segmented cylinders is illustrated and the FEM model for the tire is given in detail. The tire is treated as an elastic deformable body with the inertia effect included. Lebanon sand found in New Hampshire is used in this simulation because of the availability of a complete set of material properties in the literature. Modified Drucker-Prager/Cap plasticity constitutive law with hardening is utilized to model the sand. The obstacle is represented as an elastic body.

Driver modeling is essential to both vehicle design and control unit development. It can improve the understanding of human driving behavior and decrease the cost and risk of vehicle system verification and validation. In this paper, three driver models were implemented to simulate the behavior of drivers subject to a run-off-road recovery event. Target path planning, pursuit behavior, compensate behavior, physical limitations, and neuromuscular modeling were taken into consideration in the feedforward/feedback driver model. A transfer function driver model and a cost function based driver model from a popular vehicle simulation software were also simulated and a comparison of these three models was made. The feedforward/feedback driver model exhibited the best balance of performance with smallest overshoot (0.226m), medium settling time (1.20s) and recovery time (4.30s).

Recent research at Clemson University has focused on the development of an advanced non-pneumatic, non-elastomeric lunar wheel for NASA with superior traction. This paper reports on several concepts for tread materials and geometries that have been explored for tire-on-sand use. Specifically, fourteen concepts, involving the use of metal meshes, textile carpet materials, soft grousers, foams, and screens, were physically tested in an on-vehicle environment. Prototypes for each concept and formal test procedures to quantify traction were developed. This paper presents the results of the tests for several different concepts and the comparison between the concepts that were developed. Students developed their own testing environment through which these test procedures are implemented, an inclined hill 45 ft. in length and 8 ft. wide will approximately 6 inches deep filled with sand.

According to the National Highway Traffic Safety Administration (NHTSA), motor collisions account for nearly 2.4 million injuries and 37 thousand fatalities each year in the United States. A great deal of research has been done in the area of vehicular safety, but very little has been completed to ensure licensed drivers are properly trained. Given the inherent risks in driving itself, the test for licensure should be uniform and consistent. To address this issue, an inexpensive, portable data acquisition and analysis system has been developed for the evaluation of driver performance. A study was performed to evaluate the system, and each participant was given a normalized driver rating. The average driver rating was μ=55.6, with a standard deviation of σ=12.3. All but 3 drivers fell into the so-called “Target Zone”, defined by a Driver Rating of μ± 1σ.

In an effort to build a shear band of a lunar rover wheel which operates at lunar surface temperatures (40 to 400K), the design of a metallic cellular shear band is suggested. Six representative honeycombs with aluminum alloy (7075-T6) are tailored to have a shear modulus of 6.5MPa which is a shear modulus of an elastomer by changing cell wall thickness, cell angles, cell heights and cell lengths at meso-scale. The designed cellular solids are used for a ring typed shear band of a wheel structure at macro-scale. A structural performance such as contact pressure at the outer layer of the wheel is investigated with the honeycomb shear bands when a vertical force is applied at the center of the wheel. Cellular Materials Theory (CMT) is used to obtain in-plane effective properties of a honeycomb structure at meso-scale. Finite Element Analysis (FEA) with commercial software ABAQUS is employed to investigate the structural behavior of a wheel at macro-scale.

This set consists of three books, Design of Automotive Composites, CAE Design and Failure Analysis of Automotive Composites, and Biocomposites in Automotive Applications all developed by Dr. Charles Lu and Dr. Srikanth Pilla. Design of Automotive Composites reports successful designs of automotive composites occurred recently in this arena, CAE Design and Failure Analysis of Automotive Composites focuses on the latest use of CAE (Computer-Aided Engineering) methods in design and failure analysis of composite materials and structures, and Biocomposites in Automotive Applications, focuses on processing and characterization of biocomposites, their application in the automotive industry and new perspectives on automotive sustainability. Together, they are a focused collection providing the reader with must-read technical papers, hand-picked by the editors, supporting the growing importance of the use of composites in the ground vehicle industry. Dr. Charles Lu is H.E.

The newly initiated Clemson Motorsports Engineering Program, housed in the Department of Mechanical Engineering, provides unique educational opportunities to our students combining classroom engineering education, research, and race team experience. Additionally, the research and service projects conducted provide valuable information to race teams and companies in the automotive industry as well as involving students in both applied technology development and fundamental engineering activities. This paper describes the current activities and structure of the program together with our view for future development.