Search Results

An early development vehicle experienced an unusually high rate of windshield breakage. Most breaks were identified as due to impact, but the severity of impact was low. It was reasoned that the windshield should possess a greater level of robustness to impact. Many theories were put forth to explain the breakage data. It was universally agreed that the unusual breakage rate could be due to only one condition, but its source was indefinite. The condition present must be tensile stress. One of three situations were considered regarding its source: 1) the tensile stress was present in the glass after manufacture due to improper annealing; 2) the installation of the windshield into the vehicle body put the glass into stress; 3) some combination of the other two sources. A gray-field polariscope was used to measure the stresses of the windshield from both the manufacturing process as well as the installation in the vehicle.

The effect of hydroforming on the mechanical properties and dynamic crush behaviors of tapered aluminum 6063-T4 tubes with octagonal cross section are investigated by experiments. First, the thickness profile of the hydroformed tube is measured by non-destructive examination technique using ultrasonic thickness gauge. The effect of hydroforming on the mechanical properties of the tube is investigated by quasi-static tensile tests of specimens prepared from different regions of the tube based on the thickness profile. The effect of hydroforming on the dynamic crush behaviors of the tube is investigated by axial crush tests under dynamic loads. Specimens and tubes are tested in two different heat treatment conditions: hydroformed-T4 (as-received) and T6. The results of the quasi-static tensile tests for the specimens in hydroformed-T4 condition show different amounts of work hardening depending on the regions, which the specimens are prepared from.

Resonant frequencies of a resonant bending system with notched crankshaft sections are obtained experimentally and numerically in order to investigate the effect of notch depth on the drop of the resonant frequency of the system. Notches with the depths ranging from 1 to 5 mm, machined by an EDM (Electrical-Discharging Machining) system, were introduced in crankshaft sections at the fillet between the main crank pin and crank cheek. The resonant frequencies of the resonant bending system with the crankshaft sections with various notch depths were first obtained from the experiments. Three-dimensional finite element models of the resonant bending system with the crankshafts sections with various notch depths are then generated. The resonant frequencies based on the finite element computations are in good agreement with those based on the experimental results.

Significant efforts are underway in the automotive industry to reduce vehicle weight while maintaining performance and cost competitiveness. One such effort is the use of advanced high strength steels (AHSS) as the primary body materials method to meet weight targets using the existing automotive manufacturing infrastructure. Issues related to the stamping of AHSS are well known, and significant hurdles still exist for successful implementation. Due to material strength and mechanical behavior, springback is a major hurdle in forming AHSS. While working to form AHSS parts and reduce springback, press shops have encountered a new fracture type. The term shear fracture or local elongation has been loosely used to specify these fractures, which occur at part radii under low strains in multiphase AHSS. These fractures cause design limitations and manufacturing uncertainty.

Traditional methods used to produce a die set (from developing initial machining cutter paths through finalized die tryout to produce a part that meets design intent) begin with draw simulation and development. It is here, traditionally, that scientific evaluation of actual metal stretch and theoretical ideals end. In past programs, a designed part would be simulated for stretch and a development model created to include various die compensations (i.e. springback, overcrown, etc.) based on past experience for area and amount. At this point, the die is cut and undergoes a metamorphosis through die tryout to finally produce a quality part. This is currently an open loop system. This paper will focus on the differences in the predicted way the die should look and the actual outcome (after part buyoff).

The Auto/Steel Partnership Corrosion Project Team has completed a perforation corrosion test program consisting of on-vehicle field exposures and various accelerated tests. Steel sheet products with eight combinations of metallic and organic coatings were tested, utilizing a simple crevice coupon design. On-vehicle exposures were conducted in St. John's and Detroit for up to seven years to establish a real-world performance standard. Identical test specimens were exposed to the various accelerated tests, and the results were compared to the real-world standard. This report documents the results of these tests, and compares the accelerated test results (including SAE J2334, GM9540P, Ford APGE, CCT-I, ASTM B117, South Florida Modified Volvo, and Kure Beach (25-meter) exposures) to the on-vehicle tests. The results are compared in terms of five criteria: extent of corrosion, rank order of material performance, degree of correlation, acceleration factor, and control of test environment.

A Robust Engineering experiment was performed to determine the effects PGM loading and placement on the FTP emissions of a 4 cylinder 2.4L and two 8 cylinder 4.7L vehicles. 1.3L catalytic converters were used containing a front and rear catalyst of equal volume. The experiment is defined by a Taguchi L-8 array. Eight different combinations of catalyst PGM loadings were aged and evaluated. Results show that nmHC and NOx emissions are predominately affected by the PGM loading of the front catalyst. The rear catalyst is insensitive to either Pt or Pd which can be used at low concentrations. Results also compare the benefits of Pd and Rh to reduce emissions. Confirmation runs suggest that significant reductions in PGM cost can be achieved over baseline designs.

The automotive industry is pursuing significant cost competitive efforts to reduce vehicle weight while maintaining or improving durability and impact performance. One such effort for the body shell structure is the utilization of advanced and ultra high strength steels (AHSS and UHSS) using the existing automotive manufacturing infrastructure. Common AHSS and UHSS steels include Dual Phase (DP), Transformation Induced Plasticity (TRIP), Partial Martensitic (PM) and others. The use of these multiphase high strength steels for impact dependent components has resulted in the need for further material characterization in order to better predict impact performance and guide new material development. This paper addresses the material properties and microstructural influences on impact behavior of advanced and ultra high strength steels through the use of laboratory tests and component level testing.

Modern vehicles contain a multitude of networked electronics. This feature causes distributed functions in distributed electronics. Malfunctions occurring during EMC testing cannot be allocated precisely without detailed knowledge of the data streams. The electromagnetic environment during EMC-testing limits the possibilities of using standard solutions to detect these malfunctions. The paper will present a new tool, which is able to track the data streams in a CAN-Bus system during EMC-testing. By integrating EMC related parameters in the existing data stream of the vehicle's data bus, it is possible to keep a record of malfunctions as they occur.

A new family of automotive three-way conversion (TWC) catalyst technologies has been developed using a Precision Metal Addition (PMA) process. Precious metal (PGM) fixation onto the support occurs during the PMA step when the PGM is added to the slurry immediately prior to application to the monolith substrate. PMA slurries can be prepared with high precision and the slurry manufacturing process is greatly simplified. Further, it has been found that with the use of new generation washcoat (WC) materials, the same WC composition can be used for all three PGMs - Pt, Pd & Rh. Negative interactions between Pd and Rh in the same WC layer do not occur, providing advantages over older technologies. Thus, new WC compositions coupled with the PMA process offers precious metal flexibility. This FlexMetal family of catalyst technologies includes single layer Pd-only, Pd/Rh and Pt/Rh and dual layer bi-metal Pd/Rh and Pt/Rh and tri-metal Pt/Pd/Rh.

The vibration-generating mechanisms inside an engine are highly non-linear (combustion, valve operation, hydraulic bearing behavior, etc.). However, the engine structure, under the influence of these vibration-generating mechanisms, responds in a highly linear way. For the development and optimization of the engine structure for noise and vibration it is beneficial to use fast and ‘simple’ linear models, like linear FE-models, measured modal models or measured FRF-models. All these models allow a qualitative assessment of variants without excitation information. But, for true optimization, internal excitation spectra are needed in order to avoid that effort is spent to optimize non-critical system properties. Unfortunately, these internal excitation spectra are difficult to measure. Direct measurement of combustion pressure is still feasible, but crank-bearing forces, piston guidance forces etc. can only be identified indirectly.

In this paper, the effects of roller geometry on contact pressure and residual stress in crankshaft fillet rolling are investigated by a two-dimensional finite element analysis. The fillet rolling process is first introduced to review some characteristics of the rolling tools. A two-dimensional plane strain finite element analysis is then employed to qualitatively investigate the influence of the roller geometry. Computations have been conducted for eight different contact geometries between the primary roller and the secondary roller to investigate the geometry effect on the contact pressure distribution on the edge of the primary roller. Fatigue parameters of the primary rollers are also estimated based on the Findley fatigue theory. Then, computations have been conducted for three different contact geometries between the primary roller and the crankshaft fillet to investigate the geometry effect on the residual stress distribution near the crankshaft fillet.

More than 200 tensile-shear resistance spot welded specimens were produced and tested to analyze the effect of spot weld spacing, weld size, sheet thickness, and adhesive on the ultimate strength of joints made from a mild hot dip galvannealed steel and an unexposed quality hot dip galvannealed 590 MPa minimum tensile strength dual phase steel (DP590). The geometric layout parameters were analyzed by a design of experiment (DOE) approach. The analysis showed that weld size is a primary factor affecting the strength of the joints for a given material. It was also determined that structural adhesive created a large relative strengthening for joints made from the mild steel. Interactions of the geometrical factors are also presented.

Deposits on engine parts, and in particular in combustion chambers of modern engines are causing increasing concern in the automobile industry. Highly sophisticated engine management systems make effects on emissions or performance obvious as outgassing of unburned hydrocarbons or variation of spark advance. Reduced mean heat flux away from the cylinder influences engine thermodynamics. Extreme deposits may cause noise increase by carbon rap. A special form of combustion chamber deposits, well known under the synonym spark plug fouling, is a carbon needle on spark plugs, which can cause the total damage of the catalysts (Japanese Industrial Standard D 1606: Adaptability Test Code of Spark Plug for Automobiles) The Co-ordinating European Council for the development of performance tests for transportation fuels, lubricants, and other fluids (CEC) started the development of a new performance test in 1994.